Qiangqiang Sun
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Qiangqiang Sun has a total of 32 co-authors. Here are the top co-authors by number of shared publications:
- Xuerui Mao
Beijing Institute of Technology
5 shared publications - Kwing-So Choi
Faculty of Engineering, University of Nottingham, Nottingham, UK
3 shared publications Alexander Büscher
Airbus Operations GmbH
2 shared publicationsBruno Stefes
Airbus Operations GmbH
2 shared publications- Dandan Xiao
Beijing Institute of Technology
2 shared publications Faycal Bahri
University of Nottingham
2 shared publications
Latest Publications
- 8 June 2026
- Published by American Institute of Aeronautics and Astronautics (AIAA) in AIAA Journal
- Vol. 64 (8) , 1-17
Duty-Cycle-Dependent Vortex Dynamics in Pulsed Jet Flow Control on Swept Wings
Active flow control of high-lift multielement swept wings remains a critical yet underexplored field in aerodynamics. This study investigates the effects of the duty cycle (DC) and the jet-to-freestream velocity ratio (VR) on pulsed jet flow control (PJFC) actuators near the leading edge of a multielement swept wing with three major innovations. First, a threshold effect is identified at [ ]. Below this threshold, a low DC actuation achieves comparable or superior maximum lift enhancement relative to a high DC operation. Second, mechanistic analysis reveals that at a high DC, the initial jet-induced vortex fails to merge with the dominant shear-layer vortex, leading to the emergence of an additional high-frequency shedding mode. In contrast, a low DC actuation increases the maximum lift coefficient by expanding the favorable suction pressure region, particularly at a lower VR. Third, PJFC delays the stall angle by approximately 4–6 degrees and achieves significant drag reduction at moderate angles of attack. These findings provide novel insights into the underlying mechanisms and enable a physics-informed selection of the VR and DC in effective active flow control on swept high-lift wings.
- 8 June 2026
- Published by American Institute of Aeronautics and Astronautics (AIAA) in AIAA Journal
- Vol. 64 (8) , 1-17
Duty-Cycle-Dependent Vortex Dynamics in Pulsed Jet Flow Control on Swept Wings
Active flow control of high-lift multielement swept wings remains a critical yet underexplored field in aerodynamics. This study investigates the effects of the duty cycle (DC) and the jet-to-freestream velocity ratio (VR) on pulsed jet flow control (PJFC) actuators near the leading edge of a multielement swept wing with three major innovations. First, a threshold effect is identified at [ ]. Below this threshold, a low DC actuation achieves comparable or superior maximum lift enhancement relative to a high DC operation. Second, mechanistic analysis reveals that at a high DC, the initial jet-induced vortex fails to merge with the dominant shear-layer vortex, leading to the emergence of an additional high-frequency shedding mode. In contrast, a low DC actuation increases the maximum lift coefficient by expanding the favorable suction pressure region, particularly at a lower VR. Third, PJFC delays the stall angle by approximately 4–6 degrees and achieves significant drag reduction at moderate angles of attack. These findings provide novel insights into the underlying mechanisms and enable a physics-informed selection of the VR and DC in effective active flow control on swept high-lift wings.
- 1 February 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (2)
Joint control of icing and flow separation using co-flow jet
During climbing and descending, an aircraft operates at high angles of attack, where the boundary layer is prone to separation, resulting in increased drag and reduced lift. Additionally, these scenarios involve a high risk of ice accretion. These challenges highlight the need for an integrated control strategy capable of simultaneously addressing aerodynamic performance degradation and anti-icing requirements, both of which depend on modulating surface flow conditions. In this work, a Co-Flow Jet (CFJ) technique is proposed as a novel strategy for concurrently suppressing flow separation and mitigating ice accretion. Simulations demonstrate that the CFJ effectively introduces suction forces near the upper trailing edge, eliminating separation in this region. Meanwhile, the two-slot leading-edge blowing produces turbulent jets, generating a bubble and virtual surfaces for anti-icing around the lower leading edge and three-dimensional vortical structures around the upper leading edge. These structures reduce the pressure on the upper leading edge, enhancing lift and reducing drag, while also altering water droplet trajectories and impingement dynamics, thereby limiting ice accumulation on the upper surface. Overall, the findings indicate that the CFJ concept offers a promising pathway toward integrating aerodynamic performance enhancement with robust anti-icing capability under high-angle-of-attack conditions.
- 1 February 2026
- Published by AIP Publishing in Physics of Fluids
- Vol. 38 (2)
Joint control of icing and flow separation using co-flow jet
During climbing and descending, an aircraft operates at high angles of attack, where the boundary layer is prone to separation, resulting in increased drag and reduced lift. Additionally, these scenarios involve a high risk of ice accretion. These challenges highlight the need for an integrated control strategy capable of simultaneously addressing aerodynamic performance degradation and anti-icing requirements, both of which depend on modulating surface flow conditions. In this work, a Co-Flow Jet (CFJ) technique is proposed as a novel strategy for concurrently suppressing flow separation and mitigating ice accretion. Simulations demonstrate that the CFJ effectively introduces suction forces near the upper trailing edge, eliminating separation in this region. Meanwhile, the two-slot leading-edge blowing produces turbulent jets, generating a bubble and virtual surfaces for anti-icing around the lower leading edge and three-dimensional vortical structures around the upper leading edge. These structures reduce the pressure on the upper leading edge, enhancing lift and reducing drag, while also altering water droplet trajectories and impingement dynamics, thereby limiting ice accumulation on the upper surface. Overall, the findings indicate that the CFJ concept offers a promising pathway toward integrating aerodynamic performance enhancement with robust anti-icing capability under high-angle-of-attack conditions.
- 26 November 2025
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 256
Dynamic behaviors of ice melting on the vibrating nanosurface via acoustothermal effect
- 26 November 2025
- Published by Elsevier in International Journal of Heat and Mass Transfer
- Vol. 256
Dynamic behaviors of ice melting on the vibrating nanosurface via acoustothermal effect
- 1 October 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (10)
Start-up process of the ground vortex ahead of the engine intake with crosswind
The ground vortex formed within the crosswind degrades the power output of the aero-engine and threatens the flight takeoff safety. Considerable amounts of experiments have been conducted to investigate the flow mechanism for the formation of the ground vortex. However, the detailed transient start-up process of the ground vortex is still unclear due to the limitations of the measurement techniques. In this work, high-fidelity delayed detached eddy simulations are performed to investigate the underlying mechanism of the ground vortex formation ahead of the intake with the occurrence of crosswind. A thorough validation is conducted first to compare the simulation against the experimental data. By gradually increasing the mass flow into the intake, a near-ground shear vortex formed around the intake due to its blockage to the crosswind is enhanced by the suction of the intake and gradually approaches the highlight plane. Multiple ground vortex filaments are generated from the shear vortex at the boundary between the crosswind and the suction flow. The vortex filaments merge into one single ground vortex, and it moves upwind along the intake lip together with the lower trailing vortex. It takes 0.9–1.0 s for the ground vortex to be formed with a velocity ratio of 4.7–5.0. The formation process found in this study is different from previous research in which the ground vortex is evolved from the trailing vortex or the ambient vorticity.
- 1 October 2025
- Published by AIP Publishing in Physics of Fluids
- Vol. 37 (10)
Start-up process of the ground vortex ahead of the engine intake with crosswind
The ground vortex formed within the crosswind degrades the power output of the aero-engine and threatens the flight takeoff safety. Considerable amounts of experiments have been conducted to investigate the flow mechanism for the formation of the ground vortex. However, the detailed transient start-up process of the ground vortex is still unclear due to the limitations of the measurement techniques. In this work, high-fidelity delayed detached eddy simulations are performed to investigate the underlying mechanism of the ground vortex formation ahead of the intake with the occurrence of crosswind. A thorough validation is conducted first to compare the simulation against the experimental data. By gradually increasing the mass flow into the intake, a near-ground shear vortex formed around the intake due to its blockage to the crosswind is enhanced by the suction of the intake and gradually approaches the highlight plane. Multiple ground vortex filaments are generated from the shear vortex at the boundary between the crosswind and the suction flow. The vortex filaments merge into one single ground vortex, and it moves upwind along the intake lip together with the lower trailing vortex. It takes 0.9–1.0 s for the ground vortex to be formed with a velocity ratio of 4.7–5.0. The formation process found in this study is different from previous research in which the ground vortex is evolved from the trailing vortex or the ambient vorticity.
- 1 April 2025
- Published by American Institute of Aeronautics and Astronautics (AIAA) in AIAA Journal
- Vol. 63 (4) , 1502-1511
Joint Effects of Virtual Surfaces on Anti-Icing and Drag Reduction
The operation of the anti-icing system of an airplane can modulate its aerodynamics, whilst an aerodynamic control can alter the icing condition. Therefore, one well-designed control strategy can be expected to yield two benefits, which, however, has not been actively investigated. In this work, the constant leading-edge blowing technique is deployed to achieve joint effects on anti-icing and drag reduction, first on an airfoil and then on a half-airplane model. The results indicate that dual virtual surfaces (an inner one and an outer one) wrapping the leading edge are generated by the blowing control. The inner one prevents water droplets from impacting and accumulating on the airfoil by changing their trajectories. The outer one redirects the shear generated by the blowing and promotes its rolling up and vortex shedding, generating low-pressure zones around the upper leading edge and subsequently reducing drag significantly.
- 1 April 2025
- Published by American Institute of Aeronautics and Astronautics (AIAA) in AIAA Journal
- Vol. 63 (4) , 1502-1511
Joint Effects of Virtual Surfaces on Anti-Icing and Drag Reduction
The operation of the anti-icing system of an airplane can modulate its aerodynamics, whilst an aerodynamic control can alter the icing condition. Therefore, one well-designed control strategy can be expected to yield two benefits, which, however, has not been actively investigated. In this work, the constant leading-edge blowing technique is deployed to achieve joint effects on anti-icing and drag reduction, first on an airfoil and then on a half-airplane model. The results indicate that dual virtual surfaces (an inner one and an outer one) wrapping the leading edge are generated by the blowing control. The inner one prevents water droplets from impacting and accumulating on the airfoil by changing their trajectories. The outer one redirects the shear generated by the blowing and promotes its rolling up and vortex shedding, generating low-pressure zones around the upper leading edge and subsequently reducing drag significantly.
- Open Access
- 5 February 2025
- Published by Elsevier in Aerospace Science and Technology
- Vol. 159
Suppression of flow separation of a high-lift wing with active flow control
- 5 February 2025
- Published by Elsevier in Aerospace Science and Technology
- Vol. 159
Open AccessSuppression of flow separation of a high-lift wing with active flow control
- Open Access
- 2 July 2024
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 40 (28) , 14214-14223
Investigating Shear Stress of Ice Accumulated on Surfaces with Various Roughnesses: Effects of a Quasi-Water Layer
The investigation of the anti-icing/deicing is essential because the icing phenomenon deteriorates the natural environment and various projects. By conducting molecular dynamics simulation, this work analyzes the effect of the quasi-water layer on the ice shear stress over smooth and rough surfaces, along with the underlying physics of the quasi-water layer. The results indicate that the thickness of the quasi-water layer monotonically increases with temperature, resulting in a monotonic decrease in the ice shear stress on the smooth surface. Due to the joint effects of the smooth surface wettability and the quasi-water layer, the ice shear stress increases and then decreases to almost a constant value when the surface changes from a hydrophobic to a hydrophilic one. For rough surfaces with stripe nanostructures, when the width of the bump for one case equals the depression for the other case, the variations of shear stress with height for these two cases are almost the same. The rough surface is effective in reducing the ice shear stress compared to the smooth surface due to the thickening of the quasi-water layer. Each molecule in the quasi-water layer and its four nearest neighboring molecules gradually form a tetrahedral ice-like structure along the direction away from the surface. The radial distribution function also shows that the quasi-water layer resembles the liquid water rather than the ice structure. These findings shed light on developing anti-icing and deicing techniques.
- 2 July 2024
- Published by American Chemical Society (ACS) in Langmuir
- Vol. 40 (28) , 14214-14223
Open AccessInvestigating Shear Stress of Ice Accumulated on Surfaces with Various Roughnesses: Effects of a Quasi-Water Layer
The investigation of the anti-icing/deicing is essential because the icing phenomenon deteriorates the natural environment and various projects. By conducting molecular dynamics simulation, this work analyzes the effect of the quasi-water layer on the ice shear stress over smooth and rough surfaces, along with the underlying physics of the quasi-water layer. The results indicate that the thickness of the quasi-water layer monotonically increases with temperature, resulting in a monotonic decrease in the ice shear stress on the smooth surface. Due to the joint effects of the smooth surface wettability and the quasi-water layer, the ice shear stress increases and then decreases to almost a constant value when the surface changes from a hydrophobic to a hydrophilic one. For rough surfaces with stripe nanostructures, when the width of the bump for one case equals the depression for the other case, the variations of shear stress with height for these two cases are almost the same. The rough surface is effective in reducing the ice shear stress compared to the smooth surface due to the thickening of the quasi-water layer. Each molecule in the quasi-water layer and its four nearest neighboring molecules gradually form a tetrahedral ice-like structure along the direction away from the surface. The radial distribution function also shows that the quasi-water layer resembles the liquid water rather than the ice structure. These findings shed light on developing anti-icing and deicing techniques.
- Open Access
- 1 May 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (5)
Compressed neural networks for reduced order modeling
Reduced order modeling (ROM) techniques, such as proper orthogonal decomposition (POD) and dynamic mode decomposition (DMD), have been widely used to analyze stationary flows. Neural networks such as autoencoders are effective to reduce the dimension of non-stationary flow, but their larger storage requirements compared to POD and DMD compromise the expectations on ROM. The present work aims at compressing the autoencoder model via two distinctively different approaches, i.e., pruning and singular value decomposition (SVD). The developed algorithm is then applied to reconstruct the flow fields of typical stationary (i.e., a laminar cylinder flow and two turbulent channel flows) and non-stationary (i.e., a laminar co-rotating vortex pair) examples. It is shown that pruning and SVD reduce the size of the autoencoder network to 6% and 3% for the two simple laminar cases (or 18% and 13%, 20%, and 10% for the two complex turbulent channel flow cases), respectively, with approximately the same order of accuracy. Therefore, the proposed autoencoders optimized by the network pruning and SVD lead to effective ROM of both stationary and non-stationary flows although they require more iterations to converge than conventional methods.
- 1 May 2024
- Published by AIP Publishing in Physics of Fluids
- Vol. 36 (5)
Open AccessCompressed neural networks for reduced order modeling
Reduced order modeling (ROM) techniques, such as proper orthogonal decomposition (POD) and dynamic mode decomposition (DMD), have been widely used to analyze stationary flows. Neural networks such as autoencoders are effective to reduce the dimension of non-stationary flow, but their larger storage requirements compared to POD and DMD compromise the expectations on ROM. The present work aims at compressing the autoencoder model via two distinctively different approaches, i.e., pruning and singular value decomposition (SVD). The developed algorithm is then applied to reconstruct the flow fields of typical stationary (i.e., a laminar cylinder flow and two turbulent channel flows) and non-stationary (i.e., a laminar co-rotating vortex pair) examples. It is shown that pruning and SVD reduce the size of the autoencoder network to 6% and 3% for the two simple laminar cases (or 18% and 13%, 20%, and 10% for the two complex turbulent channel flow cases), respectively, with approximately the same order of accuracy. Therefore, the proposed autoencoders optimized by the network pruning and SVD lead to effective ROM of both stationary and non-stationary flows although they require more iterations to converge than conventional methods.
- 1 September 2022
- Published by Royal Society of Chemistry (RSC) in Nanoscale
- Vol. 14 (36) , 13324-13333
Quasi-water layer sandwiched between hexagonal ice and wall and its influences on the ice tensile stress
The presence of a quasi-water/premelting layer at the interface between wall and ice when the temperature (T) is below the melting point was extensively observed in experiments. In this work, molecular dynamics simulations are performed to analyze the underlying physics of the quasi-water layer and the effects of the layer on the ice tensile stress. The results indicate that each molecule and its four nearest neighbours in the quasi-water layer representing an equilibrium structure gradually form a tetrahedral ice-like arrangement from an unstructured liquid-like structure along the direction away from the wall. The average density of the quasi-water layer is equal to or higher than the bulk density of water at T ≥ 240 K or T ≤ 240 K respectively, and reaches 1.155 g cm−3 at T = 210 K, suggesting a structural correlation with the high-density liquid phase of water. Depending on the temperature and wall wettability, the thickness of the quasi-water layer (Hq) ranges from ∼2 Å to ∼25 Å. For prescribed hydrophilic walls, Hq increases monotonically with temperature, and is almost proportional to(Tm − T)−1/3, where Tm is the melting temperature of ice. Hq keeps an almost constant value (2 Å) as the temperature increases and rises sharply after passing a threshold temperature of T ≈ 250 K. In the joint effects of the wall wettability and quasi-water layer's thickness, the ice tensile stress decreasing monotonically at a larger temperature shows an upward trend and then reduces to almost a constant value as the wall changes from a hydrophobic to a hydrophilic one. The results reveal the potential development of anti-icing/de-icing techniques by heating the wall or modifying its surface to increase Hq.
- 1 September 2022
- Published by Royal Society of Chemistry (RSC) in Nanoscale
- Vol. 14 (36) , 13324-13333
Quasi-water layer sandwiched between hexagonal ice and wall and its influences on the ice tensile stress
The presence of a quasi-water/premelting layer at the interface between wall and ice when the temperature (T) is below the melting point was extensively observed in experiments. In this work, molecular dynamics simulations are performed to analyze the underlying physics of the quasi-water layer and the effects of the layer on the ice tensile stress. The results indicate that each molecule and its four nearest neighbours in the quasi-water layer representing an equilibrium structure gradually form a tetrahedral ice-like arrangement from an unstructured liquid-like structure along the direction away from the wall. The average density of the quasi-water layer is equal to or higher than the bulk density of water at T ≥ 240 K or T ≤ 240 K respectively, and reaches 1.155 g cm−3 at T = 210 K, suggesting a structural correlation with the high-density liquid phase of water. Depending on the temperature and wall wettability, the thickness of the quasi-water layer (Hq) ranges from ∼2 Å to ∼25 Å. For prescribed hydrophilic walls, Hq increases monotonically with temperature, and is almost proportional to(Tm − T)−1/3, where Tm is the melting temperature of ice. Hq keeps an almost constant value (2 Å) as the temperature increases and rises sharply after passing a threshold temperature of T ≈ 250 K. In the joint effects of the wall wettability and quasi-water layer's thickness, the ice tensile stress decreasing monotonically at a larger temperature shows an upward trend and then reduces to almost a constant value as the wall changes from a hydrophobic to a hydrophilic one. The results reveal the potential development of anti-icing/de-icing techniques by heating the wall or modifying its surface to increase Hq.
- Open Access
- 1 May 2022
- Published by AIP Publishing in Physics of Fluids
- Vol. 34 (5) , 054101
Linear and weakly nonlinear dominant dynamics in a boundary layer flow
The aim of this paper is to investigate the linear and weakly nonlinear dynamics in flow over a flat-plate with leading edge. Linear optimal and suboptimal inflow perturbations are obtained using a Lagrangian multiplier technique. In particular, the suboptimal inflow conditions and the corresponding downstream responses are investigated in detail for the first time. Unlike the suboptimal dynamics reported in other canonical cases such as the backward-facing step flow, the growth rate of the suboptimal perturbation is in the same order as the optimal one, and both of them depend on the lift-up mechanism even though they are orthogonal. The suboptimal mode has an additional layer of vorticity that penetrates into the boundary layer farther downstream, generating a second patch of high- and low-speed streaks. The farther suboptimal ones spread to the free-stream without entering the boundary layer. The weakly nonlinear dynamics are examined by decomposing the flow field into multiple orders of perturbations using the Volterra series. Small structures in the higher order perturbations mainly concentrate in the region farther away from wall, suggesting a mechanism of outward perturbation developments, which is opposite with the well reported inward development of perturbations, i.e., from free-stream to boundary layer. The significance of these modes is then demonstrated through a prediction of flow field from the inflow condition by exploiting the orthogonality of the modes.
- 1 May 2022
- Published by AIP Publishing in Physics of Fluids
- Vol. 34 (5) , 054101
Open AccessLinear and weakly nonlinear dominant dynamics in a boundary layer flow
The aim of this paper is to investigate the linear and weakly nonlinear dynamics in flow over a flat-plate with leading edge. Linear optimal and suboptimal inflow perturbations are obtained using a Lagrangian multiplier technique. In particular, the suboptimal inflow conditions and the corresponding downstream responses are investigated in detail for the first time. Unlike the suboptimal dynamics reported in other canonical cases such as the backward-facing step flow, the growth rate of the suboptimal perturbation is in the same order as the optimal one, and both of them depend on the lift-up mechanism even though they are orthogonal. The suboptimal mode has an additional layer of vorticity that penetrates into the boundary layer farther downstream, generating a second patch of high- and low-speed streaks. The farther suboptimal ones spread to the free-stream without entering the boundary layer. The weakly nonlinear dynamics are examined by decomposing the flow field into multiple orders of perturbations using the Volterra series. Small structures in the higher order perturbations mainly concentrate in the region farther away from wall, suggesting a mechanism of outward perturbation developments, which is opposite with the well reported inward development of perturbations, i.e., from free-stream to boundary layer. The significance of these modes is then demonstrated through a prediction of flow field from the inflow condition by exploiting the orthogonality of the modes.