Xiang Qingpei
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Xiang Qingpei has a total of 68 co-authors. Here are the top co-authors by number of shared publications:
- Zhang Yingzeng
China Acad Engn Phys, Inst Nucl Phys & Chem, Mianyang 621900, Peoples R China
10 shared publications - Jing Li
Institute of Nuclear Physics and Chemistry, China Academy of Engineering Physics, Mianyang 621900, China
6 shared publications Chen Haodong
5 shared publicationsHao Fanhua
Institute of Nuclear Physics and Chemistry, China Academy of Engineering Physics, Mianyang, 621900, China
5 shared publicationsFanhua Hao
4 shared publicationsGuo Xiaofeng
Institute of Nuclear Physics and Chemistry, China Academy of Engineering Physics, Mianyang, 621900, China
4 shared publications
Latest Publications
- Open Access
- 20 September 2026
- Published by Elsevier in SSRN Electronic Journal
Performance assessment and millisecond-scale calculation method of the next-generation radioisotope thermoelectric generator and its extended configurations
The next-generation radioisotope thermoelectric generator (NG-RTG) is a high-power RTG under development within the US Radioisotope Power Systems (RPS) Program. The detailed thermoelectric performance of this generator and its extended configurations remains unclear. Using NG-RTG Mod-1 as the baseline, one-eighth symmetry COMSOL models of the standard design and two extended configurations containing 8 and 18 general-purpose heat source (GPHS) modules were developed. To address the long solution times and convergence difficulties caused by the complex RTG structure, a millisecond-scale calculation method was also developed. It combined a one-dimensional thermal-resistance network, a Kirchhoff transformation for non-linear heat conduction problem, and an equivalent representation of the segmented unicouple to calculate load performance from open-circuit temperatures. Each calculation required approximately 20 ms, compared with tens of minutes for the corresponding finite-element model. NG-RTG (Standard) produced 251.5 We power at 28 V, consistent with the latest range reported by NASA. Despite its fewer heat source, the NG-RTG (8 GPHS) maintained a maximum specific power of 4.35 We/kg, whereas NG-RTG (18 GPHS) increased maximum specific power by 8.8%. The maximum relative error in open-circuit temperature was below 1.5%, and the output power error under load was generally within 5%; the maximum power error for NG-RTG (Standard) was only 4 We. The method also remained applicable after fuel decay, with output power errors within 1.8%. These models and the calculation method can support configuration extension, operating-parameter assessment, and rapid engineering iteration for high-power, axially stacked RTGs such as the NG-RTG.
- 20 September 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessPerformance assessment and millisecond-scale calculation method of the next-generation radioisotope thermoelectric generator and its extended configurations
The next-generation radioisotope thermoelectric generator (NG-RTG) is a high-power RTG under development within the US Radioisotope Power Systems (RPS) Program. The detailed thermoelectric performance of this generator and its extended configurations remains unclear. Using NG-RTG Mod-1 as the baseline, one-eighth symmetry COMSOL models of the standard design and two extended configurations containing 8 and 18 general-purpose heat source (GPHS) modules were developed. To address the long solution times and convergence difficulties caused by the complex RTG structure, a millisecond-scale calculation method was also developed. It combined a one-dimensional thermal-resistance network, a Kirchhoff transformation for non-linear heat conduction problem, and an equivalent representation of the segmented unicouple to calculate load performance from open-circuit temperatures. Each calculation required approximately 20 ms, compared with tens of minutes for the corresponding finite-element model. NG-RTG (Standard) produced 251.5 We power at 28 V, consistent with the latest range reported by NASA. Despite its fewer heat source, the NG-RTG (8 GPHS) maintained a maximum specific power of 4.35 We/kg, whereas NG-RTG (18 GPHS) increased maximum specific power by 8.8%. The maximum relative error in open-circuit temperature was below 1.5%, and the output power error under load was generally within 5%; the maximum power error for NG-RTG (Standard) was only 4 We. The method also remained applicable after fuel decay, with output power errors within 1.8%. These models and the calculation method can support configuration extension, operating-parameter assessment, and rapid engineering iteration for high-power, axially stacked RTGs such as the NG-RTG.
- Open Access
- 10 September 2026
- Published by Elsevier in SSRN Electronic Journal
Performance assessment and millisecond-scale calculation method of the next-generation radioisotope thermoelectric generator and its extended configurations
The next-generation radioisotope thermoelectric generator (NG-RTG) is a high-power RTG under development within the US Radioisotope Power Systems (RPS) Program. The detailed thermoelectric performance of this generator and its extended configurations remains unclear. Using NG-RTG Mod-1 as the baseline, one-eighth symmetry COMSOL models of the standard design and two extended configurations containing 8 and 18 general-purpose heat source (GPHS) modules were developed. To address the long solution times and convergence difficulties caused by the complex RTG structure, a millisecond-scale calculation method was also developed. It combined a one-dimensional thermal-resistance network, a Kirchhoff transformation for non-linear heat conduction problem, and an equivalent representation of the segmented unicouple to calculate load performance from open-circuit temperatures. Each calculation required approximately 20 ms, compared with tens of minutes for the corresponding finite-element model. NG-RTG (Standard) produced 251.5 We power at 28 V, consistent with the latest range reported by NASA. Despite its fewer heat source, the NG-RTG (8 GPHS) maintained a maximum specific power of 4.35 We/kg, whereas NG-RTG (18 GPHS) increased maximum specific power by 8.8%. The maximum relative error in open-circuit temperature was below 1.5%, and the output power error under load was generally within 5%; the maximum power error for NG-RTG (Standard) was only 4 We. The method also remained applicable after fuel decay, with output power errors within 1.8%. These models and the calculation method can support configuration extension, operating-parameter assessment, and rapid engineering iteration for high-power, axially stacked RTGs such as the NG-RTG.
- 10 September 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessPerformance assessment and millisecond-scale calculation method of the next-generation radioisotope thermoelectric generator and its extended configurations
The next-generation radioisotope thermoelectric generator (NG-RTG) is a high-power RTG under development within the US Radioisotope Power Systems (RPS) Program. The detailed thermoelectric performance of this generator and its extended configurations remains unclear. Using NG-RTG Mod-1 as the baseline, one-eighth symmetry COMSOL models of the standard design and two extended configurations containing 8 and 18 general-purpose heat source (GPHS) modules were developed. To address the long solution times and convergence difficulties caused by the complex RTG structure, a millisecond-scale calculation method was also developed. It combined a one-dimensional thermal-resistance network, a Kirchhoff transformation for non-linear heat conduction problem, and an equivalent representation of the segmented unicouple to calculate load performance from open-circuit temperatures. Each calculation required approximately 20 ms, compared with tens of minutes for the corresponding finite-element model. NG-RTG (Standard) produced 251.5 We power at 28 V, consistent with the latest range reported by NASA. Despite its fewer heat source, the NG-RTG (8 GPHS) maintained a maximum specific power of 4.35 We/kg, whereas NG-RTG (18 GPHS) increased maximum specific power by 8.8%. The maximum relative error in open-circuit temperature was below 1.5%, and the output power error under load was generally within 5%; the maximum power error for NG-RTG (Standard) was only 4 We. The method also remained applicable after fuel decay, with output power errors within 1.8%. These models and the calculation method can support configuration extension, operating-parameter assessment, and rapid engineering iteration for high-power, axially stacked RTGs such as the NG-RTG.
- Open Access
- 12 August 2026
- Published by Elsevier in SSRN Electronic Journal
Coupled Thermal-Electrical Modeling and Parametric Sensitivity Analysis of ESA 241Am-Fuled Radioisotope Thermoelectric Generator
Radioisotope Thermoelectric Generators (RTGs) fueled by ²³⁸Pu have found extensive applications in scenarios where the use of solar or other alternative energy sources is challenging, such as deep-space exploration missions. RTGs usually use 238Pu as fuel, however, due to the shortage of 238Pu in recent years, which can no longer fully meet the demands of space missions, it is necessary to seek corresponding alternative fuels. ²⁴¹Am, characterized by its long half-life and low neutron emission rate, presents a viable alternative despite its lower thermal power density. In this study, a comprehensive thermoelectric model of the ESA’s 2nd generation ²⁴¹Am fueled RTG is developed by using COMSOL Multiphysics software. Simulation results show good agreement with experimental data, with the maximum deviation of less than 3%. The simulation results detailed internal temperature and voltage distributions, revealing the working mechanisms of heat transfer and thermoelectric conversion within the RTG. Furthermore, the parametric analysis evaluates the influence of input conditions, operating environments, thermoelectric properties, and dimensional parameters on output performance, and proposes various schemes of performance enhancement, which proposes possibilities for optimizing RTG output performance and its future applications in deep space exploration.
- 12 August 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessCoupled Thermal-Electrical Modeling and Parametric Sensitivity Analysis of ESA 241Am-Fuled Radioisotope Thermoelectric Generator
Radioisotope Thermoelectric Generators (RTGs) fueled by ²³⁸Pu have found extensive applications in scenarios where the use of solar or other alternative energy sources is challenging, such as deep-space exploration missions. RTGs usually use 238Pu as fuel, however, due to the shortage of 238Pu in recent years, which can no longer fully meet the demands of space missions, it is necessary to seek corresponding alternative fuels. ²⁴¹Am, characterized by its long half-life and low neutron emission rate, presents a viable alternative despite its lower thermal power density. In this study, a comprehensive thermoelectric model of the ESA’s 2nd generation ²⁴¹Am fueled RTG is developed by using COMSOL Multiphysics software. Simulation results show good agreement with experimental data, with the maximum deviation of less than 3%. The simulation results detailed internal temperature and voltage distributions, revealing the working mechanisms of heat transfer and thermoelectric conversion within the RTG. Furthermore, the parametric analysis evaluates the influence of input conditions, operating environments, thermoelectric properties, and dimensional parameters on output performance, and proposes various schemes of performance enhancement, which proposes possibilities for optimizing RTG output performance and its future applications in deep space exploration.
- Open Access
- 8 May 2026
- Published by Elsevier in SSRN Electronic Journal
Influence of Bi2Te3 Substrates with Different Microstructures on the Thermal Stability and Kinetics of Ni/Bi2Te3 Joints
Thermoelectric technology enables direct conversion between thermal and electrical energy, and the long-term reliability of its devices depends on the stability of the interface between the thermoelectric legs and the metal electrodes. Bi2Te3-based alloys are thermoelectric materials for near-room-temperature applications, and Ni is often used as a diffusion barrier to prevent reactions between the alloy and electrodes and solder. This study systematically investigated the effect of Bi2Te3 substrates with different microstructures on the thermal stability of the Ni/Bi2Te3 interface. The study selected four Bi2Te3 thermoelectric materials: n-type zone-melted, n-type hot-extruded, p-type hot-pressed, and p-type hot-extruded. Samples were prepared by electroplating a Ni barrier layer and welding it to a Cu electrode. The samples were heat-treated at different temperatures, and the evolution of the interfacial microstructure, diffusion kinetics, and electrical performance degradation was analyzed. The results indicate that, for both n-type and p-type materials, those prepared by the hot extrusion process exhibit superior interfacial thermal stability. Microstructural analysis reveals that the interfacial reactions in n-type materials are predominantly governed by grain-boundary diffusion. In the hot-extruded n-type samples, the refined grain structure and the Bi/Se grain-boundary segregation developed during heat treatment effectively suppress the rapid grain-boundary diffusion of Ni atoms. In contrast, the interfacial reactions in p-type materials are mainly controlled by bulk diffusion. For the hot-extruded p-type samples, Bi enrichment in the region adjacent to the interfacial reaction layer increases the kinetic barrier for Ni diffusion, thereby significantly inhibiting the growth of the interfacial reaction layer.
- 8 May 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessInfluence of Bi2Te3 Substrates with Different Microstructures on the Thermal Stability and Kinetics of Ni/Bi2Te3 Joints
Thermoelectric technology enables direct conversion between thermal and electrical energy, and the long-term reliability of its devices depends on the stability of the interface between the thermoelectric legs and the metal electrodes. Bi2Te3-based alloys are thermoelectric materials for near-room-temperature applications, and Ni is often used as a diffusion barrier to prevent reactions between the alloy and electrodes and solder. This study systematically investigated the effect of Bi2Te3 substrates with different microstructures on the thermal stability of the Ni/Bi2Te3 interface. The study selected four Bi2Te3 thermoelectric materials: n-type zone-melted, n-type hot-extruded, p-type hot-pressed, and p-type hot-extruded. Samples were prepared by electroplating a Ni barrier layer and welding it to a Cu electrode. The samples were heat-treated at different temperatures, and the evolution of the interfacial microstructure, diffusion kinetics, and electrical performance degradation was analyzed. The results indicate that, for both n-type and p-type materials, those prepared by the hot extrusion process exhibit superior interfacial thermal stability. Microstructural analysis reveals that the interfacial reactions in n-type materials are predominantly governed by grain-boundary diffusion. In the hot-extruded n-type samples, the refined grain structure and the Bi/Se grain-boundary segregation developed during heat treatment effectively suppress the rapid grain-boundary diffusion of Ni atoms. In contrast, the interfacial reactions in p-type materials are mainly controlled by bulk diffusion. For the hot-extruded p-type samples, Bi enrichment in the region adjacent to the interfacial reaction layer increases the kinetic barrier for Ni diffusion, thereby significantly inhibiting the growth of the interfacial reaction layer.
- Open Access
- 1 March 2026
- Published by KEAI Publishing in Nuclear Analysis
- Vol. 5 (1)
Quantitative analysis of MMRTG power decay due to thermal inventory loss
- 1 March 2026
- Published by KEAI Publishing in Nuclear Analysis
- Vol. 5 (1)
Open AccessQuantitative analysis of MMRTG power decay due to thermal inventory loss
- Open Access
- 5 January 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (1) , 545
Influence of Structural Parameters on Thermal Stress and Performance of High-Temperature SiGe Thermoelectric Modules
Mechanical and thermoelectric performance of a SiGe thermoelectric module were investigated through finite element analysis. N-type and P-type SiGe thermoelectric materials were synthesized, and their mechanical and thermoelectric properties were experimentally measured. Thermal stress distributions within the SiGe module and the integrated “heat collector–module–heat sink” assembly are simulated, and the results were compared with the measured mechanical strength of the SiGe materials. The simulations show that among the three electrode structures evaluated—C/W/C sandwich, 0.5 mm W/C, and 0.1 mm W/C—the C/W/C sandwich configuration yields the lowest thermal stress. An inter-leg spacing of 0.5 mm also leads to reduced stress compared to a 0.1 mm gap. However, fully constraining the cold end or directly integrating the module with heat collection and dissipation components significantly increases thermal stress. The use of copper cooling plates induces higher stress than C-C plates, exceeding the tolerable strength of the materials. Simulation of a module with 28 SiGe legs (each 10 mm × 10 mm × 1.5 mm) predicts an output power of 7.42 W and a conversion efficiency of 7.11% at a hot-side temperature of 967 °C and a cold-side temperature of 412 °C.
- 5 January 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (1) , 545
Open AccessInfluence of Structural Parameters on Thermal Stress and Performance of High-Temperature SiGe Thermoelectric Modules
Mechanical and thermoelectric performance of a SiGe thermoelectric module were investigated through finite element analysis. N-type and P-type SiGe thermoelectric materials were synthesized, and their mechanical and thermoelectric properties were experimentally measured. Thermal stress distributions within the SiGe module and the integrated “heat collector–module–heat sink” assembly are simulated, and the results were compared with the measured mechanical strength of the SiGe materials. The simulations show that among the three electrode structures evaluated—C/W/C sandwich, 0.5 mm W/C, and 0.1 mm W/C—the C/W/C sandwich configuration yields the lowest thermal stress. An inter-leg spacing of 0.5 mm also leads to reduced stress compared to a 0.1 mm gap. However, fully constraining the cold end or directly integrating the module with heat collection and dissipation components significantly increases thermal stress. The use of copper cooling plates induces higher stress than C-C plates, exceeding the tolerable strength of the materials. Simulation of a module with 28 SiGe legs (each 10 mm × 10 mm × 1.5 mm) predicts an output power of 7.42 W and a conversion efficiency of 7.11% at a hot-side temperature of 967 °C and a cold-side temperature of 412 °C.
- Open Access
Dramatically Enhanced Mechanical Properties of Nano-TiN-Dispersed n-Type Bismuth Telluride by Multi-Effect Modulation
Bismuth telluride (Bi2Te3)-based alloys have been extensively employed in energy harvesting and refrigeration applications for decades. However, commercially produced Bi2Te3-based alloys using the zone-melting (ZM) technique often encounter challenges such as insufficient mechanical properties and susceptibility to cracking, particularly in n-type Bi2Te3-based alloys, which severely limit the application scenarios for bismuth telluride devices. In this work, we seek to enhance the mechanical properties of n-type Bi2Te2.7Se0.3 alloys while preserving their thermoelectrical performance by a mixed mechanism of grain refinement and the TiN composite phase-introduced pinning effect. These nanoscale processes, coupled with the addition of TiN, result in a reduction in grain size. The pinning effects of nano-TiN contribute to increased resistance to crack propagation. Finally, the TiN-dispersed Bi2Te2.7Se0.3 samples demonstrate increased hardness, bending strength and compressive strength, reaching 0.98 GPa, 36.3 MPa and 74 MPa. When compared to the ZM ingots, those represent increments of 181%, 60% and 67%, respectively. Moreover, the thermoelectric performance of the TiN-dispersed Bi2Te2.7Se0.3 samples is identical to the ZM ingots. The samples exhibit a peak dimensionless figure of merit (ZT) value of 0.957 at 375 K, with an average ZT value of 0.89 within the 325–450 K temperature range. This work has significantly enhanced mechanical properties, increasing the adaptability and reliability of bismuth telluride devices for various applications, and the multi-effect modulation of mechanical properties demonstrated in this study can be applied to other thermoelectric material systems.
Open AccessDramatically Enhanced Mechanical Properties of Nano-TiN-Dispersed n-Type Bismuth Telluride by Multi-Effect Modulation
Bismuth telluride (Bi2Te3)-based alloys have been extensively employed in energy harvesting and refrigeration applications for decades. However, commercially produced Bi2Te3-based alloys using the zone-melting (ZM) technique often encounter challenges such as insufficient mechanical properties and susceptibility to cracking, particularly in n-type Bi2Te3-based alloys, which severely limit the application scenarios for bismuth telluride devices. In this work, we seek to enhance the mechanical properties of n-type Bi2Te2.7Se0.3 alloys while preserving their thermoelectrical performance by a mixed mechanism of grain refinement and the TiN composite phase-introduced pinning effect. These nanoscale processes, coupled with the addition of TiN, result in a reduction in grain size. The pinning effects of nano-TiN contribute to increased resistance to crack propagation. Finally, the TiN-dispersed Bi2Te2.7Se0.3 samples demonstrate increased hardness, bending strength and compressive strength, reaching 0.98 GPa, 36.3 MPa and 74 MPa. When compared to the ZM ingots, those represent increments of 181%, 60% and 67%, respectively. Moreover, the thermoelectric performance of the TiN-dispersed Bi2Te2.7Se0.3 samples is identical to the ZM ingots. The samples exhibit a peak dimensionless figure of merit (ZT) value of 0.957 at 375 K, with an average ZT value of 0.89 within the 325–450 K temperature range. This work has significantly enhanced mechanical properties, increasing the adaptability and reliability of bismuth telluride devices for various applications, and the multi-effect modulation of mechanical properties demonstrated in this study can be applied to other thermoelectric material systems.
- 5 April 2023
- Published by Elsevier in Thermal Science and Engineering Progress
- Vol. 41
Modeling and thermal analysis of Step 2 GPHS for a larger safe operating temperature range
- 5 April 2023
- Published by Elsevier in Thermal Science and Engineering Progress
- Vol. 41
Modeling and thermal analysis of Step 2 GPHS for a larger safe operating temperature range