Yunchao Huang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Yunchao Huang has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Changhui Zhang
School of Water Conservancy, North China University of Water Resources and Electric Power, Zhengzhou 450046, China
1 shared publication - Danying Gao
School of Civil Engineering, Zhengzhou University, Zhengzhou 450001, China
1 shared publication - Hu Huang
School of Water Conservancy, North China University of Water Resources and Electric Power, Zhengzhou 450046, China
1 shared publication - Huanhuan Yan
School of Water Conservancy, North China University of Water Resources and Electric Power, Zhengzhou 450046, China
1 shared publication - Jiachen Sun
School of Water Conservancy, North China University of Water Resources and Electric Power, Zhengzhou 450046, China
1 shared publication Jianliang Hu
Datang Qiubei New Energy Corp Ltd, Wenshan 663203, Peoples R China
1 shared publication
Latest Publications
- Open Access
Probability Distribution and Recommended Value for the Crack Spacing Reduction Coefficient of Steel Fiber in SFRC Beams
The effect of steel fiber on the maximum crack width of steel fiber reinforced concrete (SFRC) members under normal service conditions was studied through tests on a series of 19 flexural beams, and the applicability of the crack spacing reduction coefficient of steel fiber in SFRC beams from Modified Rilem model that using for calculating maximum crack width was discussed, of which the reduction coefficient value was used to determine the influence of steel fibers on the crack width. Results show that the maximum crack width of the RC beam under bending conditions clearly decreased with the addition of fibers, and the reduction coefficient value of the crack width of the SFRC beam is greater when compared with that specified in the Modified Rilem model. The effect of steel fiber on reducing crack width was overrated, while the reduction coefficient proposed in the Modified Rilem model was used to calculate the maximum crack width. The probability of the reduction coefficient was analyzed based on experimental data collected from the relevant literature, and the reduction coefficients for different steel fiber types with various guarantee rates were obtained. Finally, the suggestion for the value of the reduction coefficient in the Modified Rilem model was proposed to be 1.19, which could be referred to for the code revision.
Open AccessProbability Distribution and Recommended Value for the Crack Spacing Reduction Coefficient of Steel Fiber in SFRC Beams
The effect of steel fiber on the maximum crack width of steel fiber reinforced concrete (SFRC) members under normal service conditions was studied through tests on a series of 19 flexural beams, and the applicability of the crack spacing reduction coefficient of steel fiber in SFRC beams from Modified Rilem model that using for calculating maximum crack width was discussed, of which the reduction coefficient value was used to determine the influence of steel fibers on the crack width. Results show that the maximum crack width of the RC beam under bending conditions clearly decreased with the addition of fibers, and the reduction coefficient value of the crack width of the SFRC beam is greater when compared with that specified in the Modified Rilem model. The effect of steel fiber on reducing crack width was overrated, while the reduction coefficient proposed in the Modified Rilem model was used to calculate the maximum crack width. The probability of the reduction coefficient was analyzed based on experimental data collected from the relevant literature, and the reduction coefficients for different steel fiber types with various guarantee rates were obtained. Finally, the suggestion for the value of the reduction coefficient in the Modified Rilem model was proposed to be 1.19, which could be referred to for the code revision.
- Open Access
- 22 June 2025
- Published by MDPI AG in Fractal and Fractional
- Vol. 9 (7) , 401
Evaluation of Mechanical Properties and Micro-Mechanism of Alkali-Activated Material with CG Under Ultrasonic Treatment from a Fractal Perspective
To mitigate the adverse effects of particle agglomeration in alkali-activated coal gangue-based cementitious (AAM–CG) materials, ultrasonic treatment and fractal theory, combined with microscopic analysis techniques were employed to investigate the physical activity of coal gangue (CG) and the microscopic mechanisms of AAM–CG materials. The results indicate that ultrasonic treatment effectively enhances the mechanical properties of AAM–CG materials. With increasing ultrasonic duration, the compressive strength initially rises and then declines, whereas it shows a continuous upward trend with increasing ultrasonic power. The optimal dispersion of CG particles in AAM–CG materials was achieved under ultrasonic treatment at 840 W for 4 min, resulting in a peak compressive strength of 106 MPa. This represents a 28.8% enhancement compared to non-sonicated controls. Ultrasonic treatment effectively disperses agglomerated particles, fully activates CG reactivity, promotes the formation of cementitious phases, improves pore-filling effects, and optimizes the internal pore structure of the material. Compared to untreated samples, the fractal dimension of the pore structure increased after ultrasonic treatment, harmful pores decreased, and porosity was reduced by 32%. This study expands the application of ultrasonic technology in the preparation of alkali-activated geopolymers and provides an efficient activation method for the resource utilization of CG.
- 22 June 2025
- Published by MDPI AG in Fractal and Fractional
- Vol. 9 (7) , 401
Open AccessEvaluation of Mechanical Properties and Micro-Mechanism of Alkali-Activated Material with CG Under Ultrasonic Treatment from a Fractal Perspective
To mitigate the adverse effects of particle agglomeration in alkali-activated coal gangue-based cementitious (AAM–CG) materials, ultrasonic treatment and fractal theory, combined with microscopic analysis techniques were employed to investigate the physical activity of coal gangue (CG) and the microscopic mechanisms of AAM–CG materials. The results indicate that ultrasonic treatment effectively enhances the mechanical properties of AAM–CG materials. With increasing ultrasonic duration, the compressive strength initially rises and then declines, whereas it shows a continuous upward trend with increasing ultrasonic power. The optimal dispersion of CG particles in AAM–CG materials was achieved under ultrasonic treatment at 840 W for 4 min, resulting in a peak compressive strength of 106 MPa. This represents a 28.8% enhancement compared to non-sonicated controls. Ultrasonic treatment effectively disperses agglomerated particles, fully activates CG reactivity, promotes the formation of cementitious phases, improves pore-filling effects, and optimizes the internal pore structure of the material. Compared to untreated samples, the fractal dimension of the pore structure increased after ultrasonic treatment, harmful pores decreased, and porosity was reduced by 32%. This study expands the application of ultrasonic technology in the preparation of alkali-activated geopolymers and provides an efficient activation method for the resource utilization of CG.
- Open Access
- 1 February 2025
- Published by IOP Publishing in Materials Research Express
- Vol. 12 (2) , 025501
Interfacial bond properties between polypropylene fiber mortar and rock with different roughness
Effective reinforcement measures for the surrounding rock of the tunnel are crucial to ensure the safety of tunnel engineering. Fibers are very effective in improving the quality of the interface; however, to promote the application of fiber mortar (FM) in tunnel lining reinforcement, it is necessary to study the bonding performance between FM and rock. The mechanical properties of ordinary mortar (OM) and FM were investigated, and bonding performance tests were conducted. The effect of polypropylene (PP) fibers on the mechanical properties and the influence of PP fibers and surface with different roughness on the bond properties were analyzed in detail. A 3D printer was used to print various structural boards to characterize different roughness levels, and the shape of the printed model was effectively controlled, thereby ensuring the consistency and repeatability of the structural board. The test results indicated that the splitting tensile strength and volumetric strain of the mortar were improved significantly with the addition of PP fibers, in which the splitting tensile strength increased by 38%, the elastic modulus and Poisson’s ratio increased, and the deformation and energy absorption capacity were enhanced; however, there was little effect on its compressive strength. The bonding performance between mortar and rock surface were enhanced with the increase in roughness, and the direct shear strength recorded the highest value while the bond specimens with a surface roughness of joint roughness coefficient 18–20, also the PP fibers improved the bond properties. This study will be helpful for promoting the application of FM in tunnel surface lining engineering.
- 1 February 2025
- Published by IOP Publishing in Materials Research Express
- Vol. 12 (2) , 025501
Open AccessInterfacial bond properties between polypropylene fiber mortar and rock with different roughness
Effective reinforcement measures for the surrounding rock of the tunnel are crucial to ensure the safety of tunnel engineering. Fibers are very effective in improving the quality of the interface; however, to promote the application of fiber mortar (FM) in tunnel lining reinforcement, it is necessary to study the bonding performance between FM and rock. The mechanical properties of ordinary mortar (OM) and FM were investigated, and bonding performance tests were conducted. The effect of polypropylene (PP) fibers on the mechanical properties and the influence of PP fibers and surface with different roughness on the bond properties were analyzed in detail. A 3D printer was used to print various structural boards to characterize different roughness levels, and the shape of the printed model was effectively controlled, thereby ensuring the consistency and repeatability of the structural board. The test results indicated that the splitting tensile strength and volumetric strain of the mortar were improved significantly with the addition of PP fibers, in which the splitting tensile strength increased by 38%, the elastic modulus and Poisson’s ratio increased, and the deformation and energy absorption capacity were enhanced; however, there was little effect on its compressive strength. The bonding performance between mortar and rock surface were enhanced with the increase in roughness, and the direct shear strength recorded the highest value while the bond specimens with a surface roughness of joint roughness coefficient 18–20, also the PP fibers improved the bond properties. This study will be helpful for promoting the application of FM in tunnel surface lining engineering.