Bryan E. Nelson
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Bryan E. Nelson has a total of 4 co-authors. Here are the top co-authors by number of shared publications:
- Jeff L. Kuehn
Caterpillar Inc., Peoria, IL 61656
2 shared publications - Kevin J. Graf
Caterpillar Inc., Peoria, IL 61656
2 shared publications - Noah D. Manring
Mechanical and Aerospace Engineering, University of Missouri-Columbia, Columbia, MO 65211
2 shared publications - Viral S. Mehta
Caterpillar, Inc., Peoria, IL 61656
2 shared publications
Latest Publications
- 29 January 2014
- Published by ASME International in Journal of Dynamic Systems, Measurement, and Control
- Vol. 136 (3) , 031004
Scaling the Speed Limitations for Axial-Piston Swash-Plate Type Hydrostatic Machines
This paper proposes a scaling law for estimating the speed limitations for a family of axial-piston swash-plate type hydrostatic machines. The speed limitations for this machine are considered from three mechanical perspectives: (1) cylinder-block tipping, (2) cylinder-block filling, and (3) slipper-tipping. As shown in the results of this research, each speed limitation is scaled by the inverse of the cube root of the volumetric displacement for the new machine. In other words, small machines are shown to have a higher speed capacity than larger machines. By scaling a baseline machine using the scale laws that are presented here, a new machine may be produced that obeys a simple rule related only to the volumetric displacement of the new machine. Serendipitously, and perhaps most usefully, all three speed limitations obey the same rule! The speed limitations that are derived in this research are compared to existing industry data of currently scaled products and it is shown that the proposed scale laws correspond well with this data.
- 29 January 2014
- Published by ASME International in Journal of Dynamic Systems, Measurement, and Control
- Vol. 136 (3) , 031004
Scaling the Speed Limitations for Axial-Piston Swash-Plate Type Hydrostatic Machines
This paper proposes a scaling law for estimating the speed limitations for a family of axial-piston swash-plate type hydrostatic machines. The speed limitations for this machine are considered from three mechanical perspectives: (1) cylinder-block tipping, (2) cylinder-block filling, and (3) slipper-tipping. As shown in the results of this research, each speed limitation is scaled by the inverse of the cube root of the volumetric displacement for the new machine. In other words, small machines are shown to have a higher speed capacity than larger machines. By scaling a baseline machine using the scale laws that are presented here, a new machine may be produced that obeys a simple rule related only to the volumetric displacement of the new machine. Serendipitously, and perhaps most usefully, all three speed limitations obey the same rule! The speed limitations that are derived in this research are compared to existing industry data of currently scaled products and it is shown that the proposed scale laws correspond well with this data.
- 10 May 2013
- Published by Wiley in Journal of Mechanical Design
- Vol. 135 (7) , 071002
Increasing the Power Density for Axial-Piston Swash-Plate Type Hydrostatic Machines
Power density is an assumed attribute of an axial-piston swash-plate type hydrostatic machine. As such, very little research has been conducted to examine the nature and limit of this machine's power density and the literature is all but void of this important topic. This paper is being written to fill this void, and to provide a thorough analysis of the machine's power density. This paper is also aimed at identifying the most significant parameters that may be adjusted to increase the power density for a typical machine. As shown in this research, the power density of an axial-piston machine depends upon four dimensionless quantities that are characteristic of the machine's rotating group. As it turns out, the allowable stress for the cylinder block is the most sensitive parameter that may be adjusted for increasing the power density of this machine. It is further shown that increasing the machine's swash-plate angle, and reducing the minimum overhang length for the pistons, will have a significant impact on the power density as well. It is significant to note that altering the number of pistons in the design has essentially no impact on the power density of the machine and therefore the selection of this design parameter must be based upon other design objectives. In conclusion, it is shown in this paper that the power density of a typical machine may be increased by as much as 64% by altering a few of these parameters within a realistic realm of constraint.
- 10 May 2013
- Published by Wiley in Journal of Mechanical Design
- Vol. 135 (7) , 071002
Increasing the Power Density for Axial-Piston Swash-Plate Type Hydrostatic Machines
Power density is an assumed attribute of an axial-piston swash-plate type hydrostatic machine. As such, very little research has been conducted to examine the nature and limit of this machine's power density and the literature is all but void of this important topic. This paper is being written to fill this void, and to provide a thorough analysis of the machine's power density. This paper is also aimed at identifying the most significant parameters that may be adjusted to increase the power density for a typical machine. As shown in this research, the power density of an axial-piston machine depends upon four dimensionless quantities that are characteristic of the machine's rotating group. As it turns out, the allowable stress for the cylinder block is the most sensitive parameter that may be adjusted for increasing the power density of this machine. It is further shown that increasing the machine's swash-plate angle, and reducing the minimum overhang length for the pistons, will have a significant impact on the power density as well. It is significant to note that altering the number of pistons in the design has essentially no impact on the power density of the machine and therefore the selection of this design parameter must be based upon other design objectives. In conclusion, it is shown in this paper that the power density of a typical machine may be increased by as much as 64% by altering a few of these parameters within a realistic realm of constraint.