Gilles Dessein
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Gilles Dessein has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Jordi Llumà
Material Science and Metallurgical Engineering Department, Universitat Politècnica de Catalunya, Barcelona, Spain
2 shared publications - Jose Antonio Travieso-Rodriguez
Mechanical Engineering Department, Universitat Politècnica de Catalunya, Barcelona, Spain
2 shared publications - Ramón Jerez-Mesa
Mechanical Engineering Department, Universitat Politècnica de Catalunya, Barcelona, Spain
2 shared publications - Vincent Wagner
Laboratoire Génie de Production, INP/ENI Tarbes, Tarbes, France
2 shared publications - El Bechir Msaddek
Laboratory of Applied Fluid Mechanics, Process Engineering and Environment, ENIS, University of Sfax, Sfax, Tunisia
1 shared publication - Eric Velázquez-Corral
Mechanical Engineering Department, Universitat Politècnica de Catalunya, Barcelona, Spain
1 shared publication
Latest Publications
- Open Access
Analysis of Ultrasonic Vibration-Assisted Ball Burnishing Process on the Tribological Behavior of AISI 316L Cylindrical Specimens
In this study, we analyzed the effects of vibration assistance, combined with a ball burnishing process, in terms of topology, residual stresses, and tribological properties on 316L shafts. The burnishing variables consisted of the variation of the input force, the number of passes, and the activation of the vibration assistance, which is based on a 40 kHz frequency and 8 μm of vibration amplitude, derived in a screening design of three factors. The results show that the medium–high level of burnishing force, high level of the number of passes, and the activation of the vibration assistance are the best options in order to improve the average roughness, the microstructure, the increase in the compressive residual stresses, and the wear enhancement, besides all variables being significant in the p-value analysis through ANOVA. Statistically, the vibration-assisted ball burnishing improved the average roughness by 2.9%, enlarged the von Mises stress on the surface by 11.5% and enhanced the wear resistance of a 316L shaft and WC-Co ball contact up to 7.3%.
Open AccessAnalysis of Ultrasonic Vibration-Assisted Ball Burnishing Process on the Tribological Behavior of AISI 316L Cylindrical Specimens
In this study, we analyzed the effects of vibration assistance, combined with a ball burnishing process, in terms of topology, residual stresses, and tribological properties on 316L shafts. The burnishing variables consisted of the variation of the input force, the number of passes, and the activation of the vibration assistance, which is based on a 40 kHz frequency and 8 μm of vibration amplitude, derived in a screening design of three factors. The results show that the medium–high level of burnishing force, high level of the number of passes, and the activation of the vibration assistance are the best options in order to improve the average roughness, the microstructure, the increase in the compressive residual stresses, and the wear enhancement, besides all variables being significant in the p-value analysis through ANOVA. Statistically, the vibration-assisted ball burnishing improved the average roughness by 2.9%, enlarged the von Mises stress on the surface by 11.5% and enhanced the wear resistance of a 316L shaft and WC-Co ball contact up to 7.3%.
- Open Access
- 1 February 2023
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 131 (2) , 551-562
Wear resistance and friction analysis of Ti6Al4V cylindrical ball-burnished specimens with and without vibration assistance
The objective of the research is to analyze the impact of the ultrasonic vibration assistance on the wear resistance due to the topography enhancement caused on Ti6Al4V cylindrical samples after surface modification through a ball burnishing process. The process parameters considered for this study are the burnishing force, the number of passes, and the addition of a 40 kHz ultrasonic assistance, which are thought to enhance the surface topography and increase the hardener effect in terms of depth. A complete screening design of 3 factors was performed, revealing that the number of passes and the vibration assistance are the most important parameters for minimizing the wear volume loss, being 170 N of burnishing force, 3 passes, and the addition of the vibration assistance as the best combination found. However, no significant difference in the friction force was observed. The topography results show that there is a decrease in the average roughness from 1.50 to 0.45 μm with optimal burnishing conditions. It was also analyzed the microstructure originated after the turning, the conventional ball burnishing, and the vibration-assisted ball burnishing, being the last optimal in terms of depth affectation to the microstructure. Therefore, these results confirm an improvement in terms of wear enhancement, friction reduction, and topography results when vibration assistance is added to a conventional ball burnishing process.
- 1 February 2023
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 131 (2) , 551-562
Open AccessWear resistance and friction analysis of Ti6Al4V cylindrical ball-burnished specimens with and without vibration assistance
The objective of the research is to analyze the impact of the ultrasonic vibration assistance on the wear resistance due to the topography enhancement caused on Ti6Al4V cylindrical samples after surface modification through a ball burnishing process. The process parameters considered for this study are the burnishing force, the number of passes, and the addition of a 40 kHz ultrasonic assistance, which are thought to enhance the surface topography and increase the hardener effect in terms of depth. A complete screening design of 3 factors was performed, revealing that the number of passes and the vibration assistance are the most important parameters for minimizing the wear volume loss, being 170 N of burnishing force, 3 passes, and the addition of the vibration assistance as the best combination found. However, no significant difference in the friction force was observed. The topography results show that there is a decrease in the average roughness from 1.50 to 0.45 μm with optimal burnishing conditions. It was also analyzed the microstructure originated after the turning, the conventional ball burnishing, and the vibration-assisted ball burnishing, being the last optimal in terms of depth affectation to the microstructure. Therefore, these results confirm an improvement in terms of wear enhancement, friction reduction, and topography results when vibration assistance is added to a conventional ball burnishing process.
- 14 February 2018
- Published by Taylor & Francis in Machining Science and Technology
- Vol. 22 (4) , 621-637
Low-frequency chatter genesis during inclined surface copy-milling with ball-end mill: Experimental study
In this study low-frequency chatter during machining of inclined surfaces with ball-end mills is experimentally investigated. An explanation of genesis of low-frequency vibrations have been proposed for various conditions: cutting direction, lead angle values, spindle speed, depth of cut. As a result, it has been proven that low-frequency chatter has more significant effect on machined surface than usual chatter. Low-frequency chatter occurs during downward milling, rather than upward milling, especially when lead angle increases. Furthermore, low-frequency chatter takes place in the beginning of cutting process, thereafter develops into steady state of usual chatter, which has no such significant effect on machined surface, as it has been shown. The results are in line with the supposition that low frequency vibrations are caused by sudden and irregular nature of shearing process, when magnitude is small.
- 14 February 2018
- Published by Taylor & Francis in Machining Science and Technology
- Vol. 22 (4) , 621-637
Low-frequency chatter genesis during inclined surface copy-milling with ball-end mill: Experimental study
In this study low-frequency chatter during machining of inclined surfaces with ball-end mills is experimentally investigated. An explanation of genesis of low-frequency vibrations have been proposed for various conditions: cutting direction, lead angle values, spindle speed, depth of cut. As a result, it has been proven that low-frequency chatter has more significant effect on machined surface than usual chatter. Low-frequency chatter occurs during downward milling, rather than upward milling, especially when lead angle increases. Furthermore, low-frequency chatter takes place in the beginning of cutting process, thereafter develops into steady state of usual chatter, which has no such significant effect on machined surface, as it has been shown. The results are in line with the supposition that low frequency vibrations are caused by sudden and irregular nature of shearing process, when magnitude is small.
- Open Access
- 8 December 2011
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 62 (1-4) , 69-81
Optimization of pocket machining strategy in HSM
- 8 December 2011
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 62 (1-4) , 69-81
Open AccessOptimization of pocket machining strategy in HSM