Ezgi Ceren Boz Noyan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Ezgi Ceren Boz Noyan has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
Antal Boldizar
Department of Industrial and Materials Science Chalmers University of Technology Gothenburg Sweden
4 shared publications- Emel Onder
Faculty of Textile Technologies and Design, Istanbul Technical University, Gumussuyu, Istanbul 34437, Türkiye
3 shared publications - Antal Boldizar
Department of Industrial and Materials Science Chalmers University of Technology Gothenburg Sweden
2 shared publications - Nihal Sarier
Faculty of Engineering, Istanbul Kültür University, Atakoy Campus, Bakirkoy, Istanbul 34156, Türkiye
2 shared publications - Refik Arat
Faculty of Science, Chemistry Department, Istanbul University, Istanbul, Türkiye
2 shared publications Abhijit Venkatesh
Department of Industrial and Materials Science, Chalmers University of Technology, Gothenburg 41296, Sweden
1 shared publication
Latest Publications
- Open Access
- 13 September 2024
- Published by Wiley in Polymer Engineering & Science
- Vol. 64 (12) , 5968-5983
Blow molding of mechanically recycled post‐consumer rigid polyethylene packaging waste
Recycled post‐consumer rigid polyethylene (PE) packaging waste was washed and compounded on a pilot scale using different processing conditions and the processability of recycled materials with blow molding was assessed. Compared to virgin grade high‐density PE, the recycled materials showed a lower crystallinity, a lower thermo‐oxidative stability, a higher ash content, a lower viscosity and melt elasticity, and a lower melt strength and drawability. The thermo‐oxidative stability varied due to the different washing media. Rheological characterization by frequency‐sweep measurements indicated that the virgin grade PE had as expected more linear‐polymer‐like characteristics whereas the recycled materials showed chain branching or crosslinking related to the processing condition during compounding. The recycled materials were successfully blow molded into 4 L‐containers where they showed less resistance to flow than the virgin grade PE. The recycled materials differed in color when different washing media were used. There were no significant differences in the mechanical properties of the 4 L‐containers made of virgin grade and recycled PE.Highlights: Washing, compounding, and blow molding of rigid polyethylene packaging waste were studied. The degradation varied depending on the washing and compounding conditions. Rheological results indicated chain branching or crosslinking due to degradation.
- 13 September 2024
- Published by Wiley in Polymer Engineering & Science
- Vol. 64 (12) , 5968-5983
Open AccessBlow molding of mechanically recycled post‐consumer rigid polyethylene packaging waste
Recycled post‐consumer rigid polyethylene (PE) packaging waste was washed and compounded on a pilot scale using different processing conditions and the processability of recycled materials with blow molding was assessed. Compared to virgin grade high‐density PE, the recycled materials showed a lower crystallinity, a lower thermo‐oxidative stability, a higher ash content, a lower viscosity and melt elasticity, and a lower melt strength and drawability. The thermo‐oxidative stability varied due to the different washing media. Rheological characterization by frequency‐sweep measurements indicated that the virgin grade PE had as expected more linear‐polymer‐like characteristics whereas the recycled materials showed chain branching or crosslinking related to the processing condition during compounding. The recycled materials were successfully blow molded into 4 L‐containers where they showed less resistance to flow than the virgin grade PE. The recycled materials differed in color when different washing media were used. There were no significant differences in the mechanical properties of the 4 L‐containers made of virgin grade and recycled PE.Highlights: Washing, compounding, and blow molding of rigid polyethylene packaging waste were studied. The degradation varied depending on the washing and compounding conditions. Rheological results indicated chain branching or crosslinking due to degradation.
- Open Access
Rheological and Functional Properties of Mechanically Recycled Post-Consumer Rigid Polyethylene Packaging Waste
The properties of recycled post-consumer rigid polyethylene packaging waste were studied, using sorted waste washed in the laboratory with water alone and with added detergent, and compared with large-scale high-intensity washed flakes. The washed flakes were compounded using three different temperature profiles in a twin-screw extruder and then injection molded. A higher compounding temperature reduced the thermo-oxidative stability, the average molecular mass, and the viscosity of the samples. Rheological measurements suggested that changes in chain branching occurred at different compounding temperatures. The strength and the elongation at break were also influenced by the compounding temperature in both the molten and solid states. Detergent washing maintained the thermo-oxidative stability in contrast to washing with water. The large-scale washed samples had a relatively high thermo-oxidative stability, a higher melt elasticity, and a lower elongation at break in both the molten and solid states than the laboratory-scale washed samples. The thermal properties, melt elasticity, Young’s modulus, yield stress, and yield strain of the samples were not, however, significantly affected by either the compounding temperature or the washing medium and intensity. The results indicated that recycled post-consumer rigid polyethylene packaging waste has properties that can support further applications in new products.
Open AccessRheological and Functional Properties of Mechanically Recycled Post-Consumer Rigid Polyethylene Packaging Waste
The properties of recycled post-consumer rigid polyethylene packaging waste were studied, using sorted waste washed in the laboratory with water alone and with added detergent, and compared with large-scale high-intensity washed flakes. The washed flakes were compounded using three different temperature profiles in a twin-screw extruder and then injection molded. A higher compounding temperature reduced the thermo-oxidative stability, the average molecular mass, and the viscosity of the samples. Rheological measurements suggested that changes in chain branching occurred at different compounding temperatures. The strength and the elongation at break were also influenced by the compounding temperature in both the molten and solid states. Detergent washing maintained the thermo-oxidative stability in contrast to washing with water. The large-scale washed samples had a relatively high thermo-oxidative stability, a higher melt elasticity, and a lower elongation at break in both the molten and solid states than the laboratory-scale washed samples. The thermal properties, melt elasticity, Young’s modulus, yield stress, and yield strain of the samples were not, however, significantly affected by either the compounding temperature or the washing medium and intensity. The results indicated that recycled post-consumer rigid polyethylene packaging waste has properties that can support further applications in new products.
- Open Access
- 20 February 2024
- Published by Wiley in Polymer Engineering & Science
- Vol. 64 (4) , 1877-1886
A comparison between laboratory‐scale and large‐scale high‐intensity washing of flexible polyethylene packaging waste
Sorted flexible polyethylene packaging waste was washed on a laboratory scale at both 25 and 40°C with water alone, with water and added NaOH, and with water and added detergent. The washed materials were then compounded using a twin‐screw extruder and injection molded. The results were compared with those for an unwashed and a large‐scale high‐intensity sample washed with NaOH at 70–80°C. An intensive washing combined with high temperature gave a lower extensibility both in the molten and solid states presumably because of a greater degradation of the recycled material. Washing with NaOH resulted in the lowest strain‐at‐break in both the melt and solid states, whereas washing with water alone or with a detergent gave similar strain‐at‐break levels. The melt strength, the stiffness and tensile strengths at room temperature, and the thermal properties were less affected by the washing procedure. Although the final properties seem to be useful in general there were still some trade‐offs between the washing condition and the degradation. While these results were expected, the influence of washing parameters on final product, for example, injection molded sample, has to our knowledge not been shown before especially regarding the mechanical properties. Highlights: Post‐consumer flexible polyethylene packaging waste was studied with a focus on washing conditions. The influence of washing conditions on thermal, rheological, and mechanical properties of recycled samples was investigated. High‐intensity washing at high temperature caused significant degradation of the material, this was to our understanding shown for the first time.
- 20 February 2024
- Published by Wiley in Polymer Engineering & Science
- Vol. 64 (4) , 1877-1886
Open AccessA comparison between laboratory‐scale and large‐scale high‐intensity washing of flexible polyethylene packaging waste
Sorted flexible polyethylene packaging waste was washed on a laboratory scale at both 25 and 40°C with water alone, with water and added NaOH, and with water and added detergent. The washed materials were then compounded using a twin‐screw extruder and injection molded. The results were compared with those for an unwashed and a large‐scale high‐intensity sample washed with NaOH at 70–80°C. An intensive washing combined with high temperature gave a lower extensibility both in the molten and solid states presumably because of a greater degradation of the recycled material. Washing with NaOH resulted in the lowest strain‐at‐break in both the melt and solid states, whereas washing with water alone or with a detergent gave similar strain‐at‐break levels. The melt strength, the stiffness and tensile strengths at room temperature, and the thermal properties were less affected by the washing procedure. Although the final properties seem to be useful in general there were still some trade‐offs between the washing condition and the degradation. While these results were expected, the influence of washing parameters on final product, for example, injection molded sample, has to our knowledge not been shown before especially regarding the mechanical properties. Highlights: Post‐consumer flexible polyethylene packaging waste was studied with a focus on washing conditions. The influence of washing conditions on thermal, rheological, and mechanical properties of recycled samples was investigated. High‐intensity washing at high temperature caused significant degradation of the material, this was to our understanding shown for the first time.
- Open Access
Washing Post-Consumer Flexible Polyethylene Packaging Waste
The mechanical and thermal properties of injection-molded recycled polyethylene were studied, specifically with respect to the influence of large-scale washing and melt-compounding of polyethylene from post-consumer packaging waste. Three types of materials were studied: those taken after sorting, after sorting and washing, and after sorting, washing, and melt-compounding, including melt-filtration, all from a large-scale material flow. The materials were further processed on a laboratory scale and compared. The results showed that large-scale washing significantly reduced thermo-oxidative stability, as well as molar mass and melt viscosity. The degradation during large-scale washing made the material susceptible to further degradation in the subsequent extrusion compounding, as shown by the differences in compounding at 240 and 200 °C using a high-shear screw configuration. The compounding parameters, screw configuration, and compounding temperature did not influence the stiffness and strength of the unwashed and large-scale-washed materials, but the elongation-at-break varied, specifically, with the increased temperature. Washing had an influence on the mechanical properties as well, and the unwashed material provided molded samples with stiffness measurements of approximately 550 MPa, whereas the large-scale-washed material provided stiffness of approximately 400 MPa. The strength measurements were approximately 15 MPa for samples made of both unwashed and large-scale-washed material, and the elongation-at-break measurements were between 50 and 150%. The large-scale-washed and compounded materials had very different mechanical properties, with stiffness measurements of approximately 320 MPa, strength of approximately 20 MPA, and elongation-at-break of approximately 350%. The significantly different mechanical properties of the large-scale-washed and compounded materials were likely due to the melt-filtration included in the compounding through the removal of metal and rubber particles, and they may also have been due to the compatibilizing and stabilizing additive used in the compounding.
Open AccessWashing Post-Consumer Flexible Polyethylene Packaging Waste
The mechanical and thermal properties of injection-molded recycled polyethylene were studied, specifically with respect to the influence of large-scale washing and melt-compounding of polyethylene from post-consumer packaging waste. Three types of materials were studied: those taken after sorting, after sorting and washing, and after sorting, washing, and melt-compounding, including melt-filtration, all from a large-scale material flow. The materials were further processed on a laboratory scale and compared. The results showed that large-scale washing significantly reduced thermo-oxidative stability, as well as molar mass and melt viscosity. The degradation during large-scale washing made the material susceptible to further degradation in the subsequent extrusion compounding, as shown by the differences in compounding at 240 and 200 °C using a high-shear screw configuration. The compounding parameters, screw configuration, and compounding temperature did not influence the stiffness and strength of the unwashed and large-scale-washed materials, but the elongation-at-break varied, specifically, with the increased temperature. Washing had an influence on the mechanical properties as well, and the unwashed material provided molded samples with stiffness measurements of approximately 550 MPa, whereas the large-scale-washed material provided stiffness of approximately 400 MPa. The strength measurements were approximately 15 MPa for samples made of both unwashed and large-scale-washed material, and the elongation-at-break measurements were between 50 and 150%. The large-scale-washed and compounded materials had very different mechanical properties, with stiffness measurements of approximately 320 MPa, strength of approximately 20 MPA, and elongation-at-break of approximately 350%. The significantly different mechanical properties of the large-scale-washed and compounded materials were likely due to the melt-filtration included in the compounding through the removal of metal and rubber particles, and they may also have been due to the compatibilizing and stabilizing additive used in the compounding.
- Open Access
- 1 December 2022
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 7 (49) , 45181-45188
Mechanical and Thermal Properties of Mixed PE Fractions from Post-Consumer Plastic Packaging Waste
The functional properties of recycled post-consumer flexible polyethylene packaging waste have been studied using materials collected and sorted at a large-scale facility in Sweden. The studied fraction was used both as received and after simple laboratory washing in water with added sodium hydroxide at 40 °C. The materials were melt-compounded with a twin-screw extruder using two different temperature profiles and two screw configurations and injection-molded into slabs, whose thermal and mechanical properties were assessed. The results showed that the mechanical properties of injection-molded samples were not changed significantly either by the washing or by the temperature or screw configuration used in the compounding. Washing reduced the viscosity and molecular mass to a minor extent. As expected, the ash content of the compounded pellets was reduced by washing. The thermo-oxidative stability decreased with increasing compounding temperature and with washing.
- 1 December 2022
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 7 (49) , 45181-45188
Open AccessMechanical and Thermal Properties of Mixed PE Fractions from Post-Consumer Plastic Packaging Waste
The functional properties of recycled post-consumer flexible polyethylene packaging waste have been studied using materials collected and sorted at a large-scale facility in Sweden. The studied fraction was used both as received and after simple laboratory washing in water with added sodium hydroxide at 40 °C. The materials were melt-compounded with a twin-screw extruder using two different temperature profiles and two screw configurations and injection-molded into slabs, whose thermal and mechanical properties were assessed. The results showed that the mechanical properties of injection-molded samples were not changed significantly either by the washing or by the temperature or screw configuration used in the compounding. Washing reduced the viscosity and molecular mass to a minor extent. As expected, the ash content of the compounded pellets was reduced by washing. The thermo-oxidative stability decreased with increasing compounding temperature and with washing.
- Open Access
- 1 November 2020
- Published by Elsevier in Polymer Degradation and Stability
- Vol. 181
The thermo-oxidative durability of polyethylene reinforced with wood-based fibres
- 1 November 2020
- Published by Elsevier in Polymer Degradation and Stability
- Vol. 181
Open AccessThe thermo-oxidative durability of polyethylene reinforced with wood-based fibres
- 1 April 2018
- Published by Elsevier in Thermochimica Acta
- Vol. 662, 135-148
Development of heat storing poly(acrylonitrile) nanofibers by coaxial electrospinning
- 1 April 2018
- Published by Elsevier in Thermochimica Acta
- Vol. 662, 135-148
Development of heat storing poly(acrylonitrile) nanofibers by coaxial electrospinning
- 9 November 2017
- Published by Springer Nature
- p. 221-235
Smart Protective Clothing for Aircraft Crew
- 1 November 2016
- Published by Elsevier in Thermochimica Acta
- Vol. 643, 83-93
Production of PEG grafted PAN copolymers and their electrospun nanowebs as novel thermal energy storage materials
- 1 November 2016
- Published by Elsevier in Thermochimica Acta
- Vol. 643, 83-93
Production of PEG grafted PAN copolymers and their electrospun nanowebs as novel thermal energy storage materials