Albert Cerrone
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Albert Cerrone has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Jacob Hochhalter
Department of Mechanical Engineering University of Utah
2 shared publications A. R. Ingraffea
School of Civil & Environmental Engineering Cornell University Ithaca NY USA
1 shared publicationAnthony Ingraffea
School of Civil and Environmental Engineering, Cornell University, 643 Rhodes Hall, Ithaca, NY 14853, USA
1 shared publication- Ashley D. Spear
University of Utah
1 shared publication - Gerd Heber
HDF Group, Champaign, IL, USA
1 shared publication J. F. Lind
Lawrence Livermore National Laboratory Livermore CA USA
1 shared publication
Latest Publications
- 27 April 2016
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 39 (6) , 737-751
A method to generate conformal finite‐element meshes from 3D measurements of microstructurally small fatigue‐crack propagation
In an effort to reproduce computationally the observed evolution of microstructurally small fatigue cracks (MSFCs), a method is presented for generating conformal, finite‐element (FE), volume meshes from 3D measurements of MSFC propagation. The resulting volume meshes contain traction‐free surfaces that conform to incrementally measured 3D crack shapes. Grain morphologies measured using near‐field high‐energy X‐ray diffraction microscopy are also represented within the FE volume meshes. Proof‐of‐concept simulations are performed to demonstrate the utility of the mesh‐generation method. The proof‐of‐concept simulations employ a crystal‐plasticity constitutive model and are performed using the conformal FE meshes corresponding to successive crack‐growth increments. Although the simulations for each crack increment are currently independent of one another, they need not be, and transfer of material‐state information among successive crack‐increment meshes is discussed. The mesh‐generation method was developed using post‐mortem measurements, yet it is general enough that it can be applied to in‐situ measurements of 3D MSFC propagation.
- 27 April 2016
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 39 (6) , 737-751
A method to generate conformal finite‐element meshes from 3D measurements of microstructurally small fatigue‐crack propagation
In an effort to reproduce computationally the observed evolution of microstructurally small fatigue cracks (MSFCs), a method is presented for generating conformal, finite‐element (FE), volume meshes from 3D measurements of MSFC propagation. The resulting volume meshes contain traction‐free surfaces that conform to incrementally measured 3D crack shapes. Grain morphologies measured using near‐field high‐energy X‐ray diffraction microscopy are also represented within the FE volume meshes. Proof‐of‐concept simulations are performed to demonstrate the utility of the mesh‐generation method. The proof‐of‐concept simulations employ a crystal‐plasticity constitutive model and are performed using the conformal FE meshes corresponding to successive crack‐growth increments. Although the simulations for each crack increment are currently independent of one another, they need not be, and transfer of material‐state information among successive crack‐increment meshes is discussed. The mesh‐generation method was developed using post‐mortem measurements, yet it is general enough that it can be applied to in‐situ measurements of 3D MSFC propagation.
- Open Access
- 27 August 2014
- Published by Wiley in International Journal of Aerospace Engineering
- Vol. 2014, 1-10
On the Effects of Modeling As-Manufactured Geometry: Toward Digital Twin
A simple, nonstandardized material test specimen, which fails along one of two different likely crack paths, is considered herein. The result of deviations in geometry on the order of tenths of a millimeter, this ambiguity in crack path motivates the consideration of as-manufactured component geometry in the design, assessment, and certification of structural systems. Herein, finite element models of as-manufactured specimens are generated and subsequently analyzed to resolve the crack-path ambiguity. The consequence and benefit of such a “personalized” methodology is the prediction of a crack path for each specimen based on its as-manufactured geometry, rather than a distribution of possible specimen geometries or nominal geometry. The consideration of as-manufactured characteristics is central to the Digital Twin concept. Therefore, this work is also intended to motivate its development.
- 27 August 2014
- Published by Wiley in International Journal of Aerospace Engineering
- Vol. 2014, 1-10
Open AccessOn the Effects of Modeling As-Manufactured Geometry: Toward Digital Twin
A simple, nonstandardized material test specimen, which fails along one of two different likely crack paths, is considered herein. The result of deviations in geometry on the order of tenths of a millimeter, this ambiguity in crack path motivates the consideration of as-manufactured component geometry in the design, assessment, and certification of structural systems. Herein, finite element models of as-manufactured specimens are generated and subsequently analyzed to resolve the crack-path ambiguity. The consequence and benefit of such a “personalized” methodology is the prediction of a crack path for each specimen based on its as-manufactured geometry, rather than a distribution of possible specimen geometries or nominal geometry. The consideration of as-manufactured characteristics is central to the Digital Twin concept. Therefore, this work is also intended to motivate its development.