Haifei Deng
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Haifei Deng has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Jinhong Yang
Institutes of Physical Science and Information Technology, Anhui University, Hefei, China
2 shared publications - Delin Chu
Anhui Univ, Sch Mat Sci & Engn, Hefei 230601, Peoples R China
1 shared publication - Desheng Cheng
Foundation Department, PLA Army Academy of Artillery and Air Defense, Hefei 230031, China
1 shared publication - Haiyan Jiang
School of Electronic Science and Applied Physics, Hefei University of Technology, Hefei 230031, China
1 shared publication - Junli Qi
College of Science, National University of Defense Technology, Changsha 410073, China
1 shared publication - Shenghong Huang
CAS Key Laboratory of Mechanical Behavior and Design of Materials, Department of Modern Mechanics, University of Science and Technology of China, Hefei 230027, China
1 shared publication
Latest Publications
- 24 April 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 46 (6) , 2191-2197
Design and Analysis of “Filling-Evacuating” High-Pressure Helium-Cooled Loop
The breeder blanket and divertor are crucial plasma facing components in a fusion reactor. The helium cooled blanket and divertor concepts have exhibited the best potential to come up to the highest safety requirements and therefore been chosen for the development object. As a result of high heat flux radiated from the plasma in the fusion reactor and high power density nuclear heat deposited by high-energy neutrons, the cooling of the first wall (FW) and the discharge of nuclear heat have become one of the major technical challenges. To demonstrate and verify the helium-cooled technology and tools of China test blanket module, and explore the feasibility and key technology of thermal hydraulics process of helium-cooled divertor, we have creatively adopted the ``filling-evacuating'' approach to design and fabricate the high-pressure helium-cooled loop (HPHCL), in which a mock-up of reduced-scale helium-cooled blanket module is designed and manufactured as a test section. Based on different experimental cases, the operating pressures of helium at mock-up range from 3 to 10 MPa and the maximum mass flow rate can reach up to 0.21 kg/s. In this paper, the design scheme of the HPHCL is presented, and the key issues of engineering manufacture and the test cases are calculated and analyzed. The helium gas flow and the heat transfer are calculated according to the test working conditions of the referenced International Thermonuclear Experimental Reactor TBM's FW surface heat flux, using ANSYS fluid dynamics software FLUENT. The results will provide support for the follow-up fabrication of test system and implementation of the tests.
- 24 April 2018
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 46 (6) , 2191-2197
Design and Analysis of “Filling-Evacuating” High-Pressure Helium-Cooled Loop
The breeder blanket and divertor are crucial plasma facing components in a fusion reactor. The helium cooled blanket and divertor concepts have exhibited the best potential to come up to the highest safety requirements and therefore been chosen for the development object. As a result of high heat flux radiated from the plasma in the fusion reactor and high power density nuclear heat deposited by high-energy neutrons, the cooling of the first wall (FW) and the discharge of nuclear heat have become one of the major technical challenges. To demonstrate and verify the helium-cooled technology and tools of China test blanket module, and explore the feasibility and key technology of thermal hydraulics process of helium-cooled divertor, we have creatively adopted the ``filling-evacuating'' approach to design and fabricate the high-pressure helium-cooled loop (HPHCL), in which a mock-up of reduced-scale helium-cooled blanket module is designed and manufactured as a test section. Based on different experimental cases, the operating pressures of helium at mock-up range from 3 to 10 MPa and the maximum mass flow rate can reach up to 0.21 kg/s. In this paper, the design scheme of the HPHCL is presented, and the key issues of engineering manufacture and the test cases are calculated and analyzed. The helium gas flow and the heat transfer are calculated according to the test working conditions of the referenced International Thermonuclear Experimental Reactor TBM's FW surface heat flux, using ANSYS fluid dynamics software FLUENT. The results will provide support for the follow-up fabrication of test system and implementation of the tests.
- 9 November 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 46 (5) , 1372-1376
Preliminary Experimental Study on Hypervapotron Heat Transfer for High Heat Flux Components
A hypervapotron (HV) loop test facility was built to conduct some experiments of heat transfer. Phenomena of HV were observed using the techniques of planar laser-induced fluorescence, high-speed photography, and particle image velocimetry. According to the design of the ITER cooling water system, the fluid flow and condition parameters were utilized: 1) CuCrZr alloy material; 2) triangular and rectangular fin structures; 3) inlet subcooling temperature of 298 K; and 4) rhodamine B solution flow velocity of 0.3-0.5 m/s. It was found that the heat transfer coefficient of the rectangular fin was 1.3-1.5 times higher than that of the triangular fin under the same test conditions. Furthermore, the preliminary mechanism of the heat transfer was explained by the coupling effect of the vortex flow with vapor bubble in the fin pitch, and the heat transfer efficiency was extraordinarily dependent on maintaining the time of vortex formation between the fins.
- 9 November 2017
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 46 (5) , 1372-1376
Preliminary Experimental Study on Hypervapotron Heat Transfer for High Heat Flux Components
A hypervapotron (HV) loop test facility was built to conduct some experiments of heat transfer. Phenomena of HV were observed using the techniques of planar laser-induced fluorescence, high-speed photography, and particle image velocimetry. According to the design of the ITER cooling water system, the fluid flow and condition parameters were utilized: 1) CuCrZr alloy material; 2) triangular and rectangular fin structures; 3) inlet subcooling temperature of 298 K; and 4) rhodamine B solution flow velocity of 0.3-0.5 m/s. It was found that the heat transfer coefficient of the rectangular fin was 1.3-1.5 times higher than that of the triangular fin under the same test conditions. Furthermore, the preliminary mechanism of the heat transfer was explained by the coupling effect of the vortex flow with vapor bubble in the fin pitch, and the heat transfer efficiency was extraordinarily dependent on maintaining the time of vortex formation between the fins.