Enrico Munari
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Enrico Munari has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Klaus Brun
Southwest Research Institute, San Antonio, TX 78238
2 shared publications - Michele Pinelli
Department of Engineering, University of Ferrara, 44122 Ferrara, Italy
2 shared publications - Mirko Morini
Interdepartmental Research Center on Food Safety, Technology and Innovation (SITEIA.PARMA), University of Parma, Tecnopolo Padiglione 33, Campus Universitario, 43124 Parma, Italy
2 shared publications - Rainer Kurz
Solar Turbines Incorporated, San Diego, CA 92123
2 shared publications - Sarah Simons
Southwest Research Institute, San Antonio, TX 78238
2 shared publications
Latest Publications
- 19 September 2017
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 140 (1) , 012602
Measurement and Prediction of Centrifugal Compressor Axial Forces During Surge—Part II: Dynamic Surge Model
The force acting on centrifugal compressors is an important parameter to be considered throughout the operating life of these turbomachines. When the compressor is operating in surge conditions, these forces can become highly dangerous for the mechanical and aerodynamic structures. This instability is usually avoided in industrial applications, but the antisurge system may not react in time when emergency shutdowns or power failures take place. During these rapid transients, surge can develop, generating unsteady forces which can harm the close clearance components of the compressor. Therefore, the capability to predict the characteristics and the dynamics of these surge forces would allow the estimation of the off-design fatigue cycles produced on these components by surge. Currently, no validated method exists to predict the frequency and amplitude of the surge forces and determine the potential damage of these components. In this paper, a lumped parameter model, developed by using the bond graph approach to predict the dynamic surge fluid-dynamic oscillations, is presented. The model requires the geometry and the steady-state performance maps of the compressor as inputs, together with the piping system configuration characteristics. The simulator is provided with a supplementary tool to estimate the axial force frequency and amplitude, taking into consideration all the contributions to the axial fluid-dynamic thrust, the stiffness-damping of the thrust bearing, and the mass of the rotor. The model was tuned and validated using the test case axial force data from the Southwest Research Institute (SWRI) facility. The model has shown good agreement with the experimental results which implies that it can offer significant information about the severity of a surge event and the quantification of the machine performance losses together with possible damage to the close clearance components. This study is a first important step that can lead to schedule optimization for maintenance and repair activities.
- 19 September 2017
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 140 (1) , 012602
Measurement and Prediction of Centrifugal Compressor Axial Forces During Surge—Part II: Dynamic Surge Model
The force acting on centrifugal compressors is an important parameter to be considered throughout the operating life of these turbomachines. When the compressor is operating in surge conditions, these forces can become highly dangerous for the mechanical and aerodynamic structures. This instability is usually avoided in industrial applications, but the antisurge system may not react in time when emergency shutdowns or power failures take place. During these rapid transients, surge can develop, generating unsteady forces which can harm the close clearance components of the compressor. Therefore, the capability to predict the characteristics and the dynamics of these surge forces would allow the estimation of the off-design fatigue cycles produced on these components by surge. Currently, no validated method exists to predict the frequency and amplitude of the surge forces and determine the potential damage of these components. In this paper, a lumped parameter model, developed by using the bond graph approach to predict the dynamic surge fluid-dynamic oscillations, is presented. The model requires the geometry and the steady-state performance maps of the compressor as inputs, together with the piping system configuration characteristics. The simulator is provided with a supplementary tool to estimate the axial force frequency and amplitude, taking into consideration all the contributions to the axial fluid-dynamic thrust, the stiffness-damping of the thrust bearing, and the mass of the rotor. The model was tuned and validated using the test case axial force data from the Southwest Research Institute (SWRI) facility. The model has shown good agreement with the experimental results which implies that it can offer significant information about the severity of a surge event and the quantification of the machine performance losses together with possible damage to the close clearance components. This study is a first important step that can lead to schedule optimization for maintenance and repair activities.
- 19 September 2017
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 140 (1) , 012601
Measurement and Prediction of Centrifugal Compressor Axial Forces During Surge—Part I: Surge Force Measurements
Centrifugal compressor impellers and shafts are subject to severe fluctuating axial and radial forces when operating in surge. These forces can cause severe damage to the close clearance components of a centrifugal compressor such as the thrust and radial bearings, interstage and dry gas seals, and balance piston. Being able to accurately quantify the cyclic surge forces on the close clearance components of the compressor allows the user to determine whether an accidental surge event, or emergency shutdown (ESD) transient, has caused damage requiring inspection, repair, or part replacement. For the test, a 700 hp (∼520 kW) industrial air centrifugal compressor was operated in surge at speeds ranging from 7000 to 13,000 rpm and pressure ratios from 1.2 to 1.8. The axial surge forces were directly measured using axial load cells on the thrust bearings. Suction and discharge pressures, proximity probe axial shaft position, flows, and temperatures were also measured. Time domain and frequency plots of axial vibration and dynamic pulsations showed the impact of the operating conditions on surge force amplitudes and frequencies. A surge severity coefficient was also derived as a simple screening tool to evaluate the magnitude of potential damage to a compressor during surge.
- 19 September 2017
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 140 (1) , 012601
Measurement and Prediction of Centrifugal Compressor Axial Forces During Surge—Part I: Surge Force Measurements
Centrifugal compressor impellers and shafts are subject to severe fluctuating axial and radial forces when operating in surge. These forces can cause severe damage to the close clearance components of a centrifugal compressor such as the thrust and radial bearings, interstage and dry gas seals, and balance piston. Being able to accurately quantify the cyclic surge forces on the close clearance components of the compressor allows the user to determine whether an accidental surge event, or emergency shutdown (ESD) transient, has caused damage requiring inspection, repair, or part replacement. For the test, a 700 hp (∼520 kW) industrial air centrifugal compressor was operated in surge at speeds ranging from 7000 to 13,000 rpm and pressure ratios from 1.2 to 1.8. The axial surge forces were directly measured using axial load cells on the thrust bearings. Suction and discharge pressures, proximity probe axial shaft position, flows, and temperatures were also measured. Time domain and frequency plots of axial vibration and dynamic pulsations showed the impact of the operating conditions on surge force amplitudes and frequencies. A surge severity coefficient was also derived as a simple screening tool to evaluate the magnitude of potential damage to a compressor during surge.