Celso Eduardo Cruz-González
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Celso Eduardo Cruz-González has a total of 80 co-authors. Here are the top co-authors by number of shared publications:
- Isidro Guzmán-Flores
Facultad de Sistemas, Universidad Autónoma de Coahuila, Saltillo, México
10 shared publications - Benjamín Vargas-Arista
Tecnologico Nacional de Mexico, Instituto Tecnologico de Tlalnepantla
9 shared publications - Everardo Efrén Granda Gutiérrez
Universidad Autónoma del Estado de México
4 shared publications Christian Félix-Martínez
3 shared publications- Dora Irma Martínez-Delgado
Universidad Autonóma de Nuevo León
3 shared publications Juan Manuel Salgado-López
3 shared publications
Latest Publications
- 29 October 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
Analysis of mechanical strength and corrosion resistance in AA6061-T6 aluminum alloy through optimized heat treatment
This work examines how heat-treatment parameters affect the mechanical properties, corrosion resistance, and fracture behavior of commercial AA6061 aluminum alloy. We used a Taguchi L 9 (3 4 ) orthogonal experimental design to evaluate the effects of solutionizing temperature (520–540 °C), solutionizing duration (3–5 h), aging temperature (150–170 °C), and aging duration (12–24 h). This research challenges the conventional assumption that maximizing strength in AA6061 inherently degrades electrochemical stability. By modifying thermal parameters that influence the alloy's microstructure, tensile properties, and fracture mechanisms, we determined that the optimal combination of process parameters was solutionizing at 540 °C for 3 h followed by aging at 170 °C for 18 h, which produced the highest ultimate tensile strength of 293 MPa and a hardness of 91 HV due to a refined precipitate distribution. Microstructural evaluation confirmed Mg 2 Si (β) precipitates and Al-Fe-Si intermetallics. Electrochemical tests in 3.5 wt.% NaCl showed a corrosion rate of 0.0092 mm/year, better than the as-received alloy's rate of 0.0639 mm/year. Fractographic analysis confirmed ductile failure via microvoid coalescence with finer dimples, indicating uniform deformation. Our results show that thermal processing can improve the mechanical properties of AA6061 while preserving its corrosion resistance.
- 29 October 2026
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part L: Journal of Materials: Design and Applications
Analysis of mechanical strength and corrosion resistance in AA6061-T6 aluminum alloy through optimized heat treatment
This work examines how heat-treatment parameters affect the mechanical properties, corrosion resistance, and fracture behavior of commercial AA6061 aluminum alloy. We used a Taguchi L 9 (3 4 ) orthogonal experimental design to evaluate the effects of solutionizing temperature (520–540 °C), solutionizing duration (3–5 h), aging temperature (150–170 °C), and aging duration (12–24 h). This research challenges the conventional assumption that maximizing strength in AA6061 inherently degrades electrochemical stability. By modifying thermal parameters that influence the alloy's microstructure, tensile properties, and fracture mechanisms, we determined that the optimal combination of process parameters was solutionizing at 540 °C for 3 h followed by aging at 170 °C for 18 h, which produced the highest ultimate tensile strength of 293 MPa and a hardness of 91 HV due to a refined precipitate distribution. Microstructural evaluation confirmed Mg 2 Si (β) precipitates and Al-Fe-Si intermetallics. Electrochemical tests in 3.5 wt.% NaCl showed a corrosion rate of 0.0092 mm/year, better than the as-received alloy's rate of 0.0639 mm/year. Fractographic analysis confirmed ductile failure via microvoid coalescence with finer dimples, indicating uniform deformation. Our results show that thermal processing can improve the mechanical properties of AA6061 while preserving its corrosion resistance.
- 12 August 2026
- Published by SAGE Publications in Journal of Composite Materials
Eco-friendly smart strain sensors: Influence of Cu-nanoparticles on electrical and piezo-resistive performance of sustainable sisal fiber-reinforced thermoplastic elastomers
The development of sustainable self-sensing composites remains limited by the lack of recyclable polymer matrices reinforced with natural fibers that can simultaneously deliver adequate mechanical performance and reliable electrical functionality. Currently, a significant understanding of the mechanical behavior of fiber-reinforced composite structures, but an important gap in knowledge remains in the way Cu nanoparticles influence the electromechanical performance of thermoplastic elastomer/sisal composites. Consequently, this work aims to bridge the gap in understanding the effect of Cu nanoparticles on the electrical conductivity and piezo-resistive behavior of these composite materials. Sandwich laminates were manufactured using thermoplastic elastomer as matrix and sisal fibers coated with copper nanoparticles whose molar concentrations ranged from 0.2 to 0.8 M. The test specimens were tested via FTIR, scanning electron microscopy, and electromechanical tensile tests to evaluate piezo-resistive behavior. The microscopic observations showed that the 0.8 M test sample had an even nanoparticle distribution as well as better interlocking. The Young’s modulus reached 0.59 GPa, while 9.64 MPa for tensile strength. Also, electrical conductivity increased proportionally with molarity reching its higher value at 0.8 M (5.30 × 10 −1 S.m −1 ). These findings demonstrate that combining Cu nanoparticle-functionalized sisal fibers with a recyclable thermoplastic elastomer matrix constitutes a promising strategy for developing eco-friendly multifunctional composites for smart sensing applications within a circular economy framework.
- 12 August 2026
- Published by SAGE Publications in Journal of Composite Materials
Eco-friendly smart strain sensors: Influence of Cu-nanoparticles on electrical and piezo-resistive performance of sustainable sisal fiber-reinforced thermoplastic elastomers
The development of sustainable self-sensing composites remains limited by the lack of recyclable polymer matrices reinforced with natural fibers that can simultaneously deliver adequate mechanical performance and reliable electrical functionality. Currently, a significant understanding of the mechanical behavior of fiber-reinforced composite structures, but an important gap in knowledge remains in the way Cu nanoparticles influence the electromechanical performance of thermoplastic elastomer/sisal composites. Consequently, this work aims to bridge the gap in understanding the effect of Cu nanoparticles on the electrical conductivity and piezo-resistive behavior of these composite materials. Sandwich laminates were manufactured using thermoplastic elastomer as matrix and sisal fibers coated with copper nanoparticles whose molar concentrations ranged from 0.2 to 0.8 M. The test specimens were tested via FTIR, scanning electron microscopy, and electromechanical tensile tests to evaluate piezo-resistive behavior. The microscopic observations showed that the 0.8 M test sample had an even nanoparticle distribution as well as better interlocking. The Young’s modulus reached 0.59 GPa, while 9.64 MPa for tensile strength. Also, electrical conductivity increased proportionally with molarity reching its higher value at 0.8 M (5.30 × 10 −1 S.m −1 ). These findings demonstrate that combining Cu nanoparticle-functionalized sisal fibers with a recyclable thermoplastic elastomer matrix constitutes a promising strategy for developing eco-friendly multifunctional composites for smart sensing applications within a circular economy framework.
- Open Access
- 23 April 2026
- Published by Elsevier in SSRN Electronic Journal
Influence of the Cu nanoparticles upon the electrical conductivity and piezo-resistive performance of natural fiber-reinforced thermoplastic elastomers
The need of the developing of bio-based composites with improved functionalities, is growing because the support that governments are giving to circular economy. In this work, the influence of the addition of copper nanoparticles upon electrical conductivity and piezo-resistive behavior of thermoplastic elastomers reinforced with sisal natural fibers. Thus, sandwich laminates were manufactured using thermoplastic elastomer as matrix and sisal fibers coated with copper nanoparticles which molar concentrations ranged from 0.2~0.8M. The test specimens, were tested by FTIR, scanning electron microscopy and electromechanical tensile tests to evaluate piezo-resistive behavior. The microscopic observations, showed that the 0.8M test sample had an even nano-particle distribution as well as better interlocking. Also, the Young´s modulus’s and tensile strength yielded values of 0.59GPa and 9.64MPa respectively. It worth mention that the electric conductivity increased proportionally with molarity, reaching it maximum at 0.8M (5.30 x 10−5 S/m). Finally, the piezo-resistive curve revealed that the composite tracked the stress-strain path, thus suggesting its potential integration as smart sensor.
- 23 April 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessInfluence of the Cu nanoparticles upon the electrical conductivity and piezo-resistive performance of natural fiber-reinforced thermoplastic elastomers
The need of the developing of bio-based composites with improved functionalities, is growing because the support that governments are giving to circular economy. In this work, the influence of the addition of copper nanoparticles upon electrical conductivity and piezo-resistive behavior of thermoplastic elastomers reinforced with sisal natural fibers. Thus, sandwich laminates were manufactured using thermoplastic elastomer as matrix and sisal fibers coated with copper nanoparticles which molar concentrations ranged from 0.2~0.8M. The test specimens, were tested by FTIR, scanning electron microscopy and electromechanical tensile tests to evaluate piezo-resistive behavior. The microscopic observations, showed that the 0.8M test sample had an even nano-particle distribution as well as better interlocking. Also, the Young´s modulus’s and tensile strength yielded values of 0.59GPa and 9.64MPa respectively. It worth mention that the electric conductivity increased proportionally with molarity, reaching it maximum at 0.8M (5.30 x 10−5 S/m). Finally, the piezo-resistive curve revealed that the composite tracked the stress-strain path, thus suggesting its potential integration as smart sensor.
- Open Access
- 19 December 2025
- Published by Elsevier in Engineering Failure Analysis
- Vol. 186
Predicting stress–strain curves using a new deep learning model based on fractography
- 19 December 2025
- Published by Elsevier in Engineering Failure Analysis
- Vol. 186
Open AccessPredicting stress–strain curves using a new deep learning model based on fractography
- Open Access
- 28 June 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (13) , 5679
Development of an Image Processing Application for Element Detection in a Printed Circuit Board Manufacturing Cell
Industrial automation in the manufacturing environment has revolutionized production and manufacturing in many industries, generating significant improvements in efficiency, quality, and process effectiveness. However, it has also posed challenges related to feedback in manufacturing environment monitoring systems, and increasing the effectiveness, productivity, and quality in industrial production. Feedback systems in the manufacturing environment are fundamental to industrial automation, which is why an application has been developed for the detection of elements in a printed circuit board manufacturing cell. The solution presented in this article proposes implementing a continuous feedback system with the ability to provide real-time information to identify the location of elements in a manufacturing cell and potentially detect anomalies, with the goal of improving the manufacturing process appropriately.
- 28 June 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (13) , 5679
Open AccessDevelopment of an Image Processing Application for Element Detection in a Printed Circuit Board Manufacturing Cell
Industrial automation in the manufacturing environment has revolutionized production and manufacturing in many industries, generating significant improvements in efficiency, quality, and process effectiveness. However, it has also posed challenges related to feedback in manufacturing environment monitoring systems, and increasing the effectiveness, productivity, and quality in industrial production. Feedback systems in the manufacturing environment are fundamental to industrial automation, which is why an application has been developed for the detection of elements in a printed circuit board manufacturing cell. The solution presented in this article proposes implementing a continuous feedback system with the ability to provide real-time information to identify the location of elements in a manufacturing cell and potentially detect anomalies, with the goal of improving the manufacturing process appropriately.
- Open Access
- 21 June 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (13) , 5407
Enhancing the Mechanical Properties of a 6061 Aluminum Alloy by Heat Treatment from the Perspective of Taguchi Design-of-Experiments
This research investigates the heat treatment parameters of 6061-aluminum alloy to enhance its mechanical properties. The Taguchi design-of-experiments (DOE) method was employed to systematically examine the effects of solutionizing temperature, solutionizing time, aging temperature, and aging time on the tensile strength of the alloy. Mechanical testing suggested a major influence of solutionizing and aging temperatures on the ultimate tensile strength of the alloy. The samples subjected to a solutionizing temperature of 540 °C for 3 h, followed by aging at 170 °C for 18 h, exhibited the highest ultimate tensile strength (293.7 MPa). Conversely, the samples processed at the lowest levels of these parameters displayed the lowest ultimate tensile strength (193.7 MPa). Microstructural analysis confirmed the formation of equiaxed grains, strengthening precipitates, precipitate clusters, and β (Mg2Si) precipitates alongside Fe-Al-Si dispersoids. Energy-dispersive X-ray spectroscopy (EDS) analysis detected the presence of elemental precursors of β phase (Al-Mg-Si) and dispersoid-forming elements (Al-Fe-Si). X-ray diffraction spectroscopy (XRD) analysis revealed the persistence of the β phase in the alloy, indicating its contribution to the improved mechanical properties, which are mainly obtained by aging precipitation phases. Fracture analysis showed a ductile fracture mechanism, and examining fractured samples supported the findings of enhanced tensile properties resulting from the adequate selection of heat treatment parameters. We employed ANOVA (analysis of variance) to analyze the DOE results, using a multiple regression model to express the ultimate tensile strength of the alloy in terms of the variables used in the design. This yielded an adjusted coefficient of determination of 89.75%, indicating a high level of explained variability in the test data for evaluating the model’s predictive capacity.
- 21 June 2024
- Published by MDPI AG in Applied Sciences
- Vol. 14 (13) , 5407
Open AccessEnhancing the Mechanical Properties of a 6061 Aluminum Alloy by Heat Treatment from the Perspective of Taguchi Design-of-Experiments
This research investigates the heat treatment parameters of 6061-aluminum alloy to enhance its mechanical properties. The Taguchi design-of-experiments (DOE) method was employed to systematically examine the effects of solutionizing temperature, solutionizing time, aging temperature, and aging time on the tensile strength of the alloy. Mechanical testing suggested a major influence of solutionizing and aging temperatures on the ultimate tensile strength of the alloy. The samples subjected to a solutionizing temperature of 540 °C for 3 h, followed by aging at 170 °C for 18 h, exhibited the highest ultimate tensile strength (293.7 MPa). Conversely, the samples processed at the lowest levels of these parameters displayed the lowest ultimate tensile strength (193.7 MPa). Microstructural analysis confirmed the formation of equiaxed grains, strengthening precipitates, precipitate clusters, and β (Mg2Si) precipitates alongside Fe-Al-Si dispersoids. Energy-dispersive X-ray spectroscopy (EDS) analysis detected the presence of elemental precursors of β phase (Al-Mg-Si) and dispersoid-forming elements (Al-Fe-Si). X-ray diffraction spectroscopy (XRD) analysis revealed the persistence of the β phase in the alloy, indicating its contribution to the improved mechanical properties, which are mainly obtained by aging precipitation phases. Fracture analysis showed a ductile fracture mechanism, and examining fractured samples supported the findings of enhanced tensile properties resulting from the adequate selection of heat treatment parameters. We employed ANOVA (analysis of variance) to analyze the DOE results, using a multiple regression model to express the ultimate tensile strength of the alloy in terms of the variables used in the design. This yielded an adjusted coefficient of determination of 89.75%, indicating a high level of explained variability in the test data for evaluating the model’s predictive capacity.
- 1 June 2024
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 133 (3-4) , 1519-1530
High and low cycle fatigue characterization for 1.2709 maraging steel at different additively manufacturing conditions
- 1 June 2024
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 133 (3-4) , 1519-1530
High and low cycle fatigue characterization for 1.2709 maraging steel at different additively manufacturing conditions
- 2 January 2024
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 130 (7-8) , 3355-3371
Microstructure, hardness, and wear resistance at room and high temperature of Stellite-6/WC-6Co coatings deposited by laser cladding process
- 2 January 2024
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 130 (7-8) , 3355-3371
Microstructure, hardness, and wear resistance at room and high temperature of Stellite-6/WC-6Co coatings deposited by laser cladding process
- Open Access
Tailored Time–Temperature Transformation Diagram for IN718 Alloy Obtained via Powder Bed Fusion Additive Manufacturing: Phase Behavior and Precipitation Dynamic
Experimental and computational approaches were used to study the microstructure of IN718 produced via powder bed fusion additive manufacturing (PBF-AM). The presence, chemical composition, and distribution of stable and metastable phases (γ′′, δ, MC, and Laves) were also analyzed. The information obtained from the microstructural study was used to construct a tailored time–temperature transformation (TTT) diagram customized for additive manufacturing of IN718. Experimental techniques, including differential scanning calorimetry (DSC), scanning electron microscopy, energy dispersive X-ray spectroscopy, and electron backscatter diffraction (EBSD), were employed to establish the morphological, chemical, and structural characteristics of the microstructure. The Thermo-Calc software and a Scheil–Gulliver model were used to analyze the presence and behavior of phase transformations during heating and cooling processes under non-thermodynamic equilibrium conditions, typical of AM processes. Unlike conventional TTT diagrams of this alloy, the diagram presented here reveals that the precipitation of γ′′ and δ phases occurs at lower temperatures and shorter times in AM-manufactured parts. Significantly, the superposition of γ′′ and δ phase curves in the proposed diagram underscores the interdependence between these phases. This TTT diagram is a valuable insight that can help in the development of heat treatment processes and quality control for IN718 produced via PBF-AM.
Open AccessTailored Time–Temperature Transformation Diagram for IN718 Alloy Obtained via Powder Bed Fusion Additive Manufacturing: Phase Behavior and Precipitation Dynamic
Experimental and computational approaches were used to study the microstructure of IN718 produced via powder bed fusion additive manufacturing (PBF-AM). The presence, chemical composition, and distribution of stable and metastable phases (γ′′, δ, MC, and Laves) were also analyzed. The information obtained from the microstructural study was used to construct a tailored time–temperature transformation (TTT) diagram customized for additive manufacturing of IN718. Experimental techniques, including differential scanning calorimetry (DSC), scanning electron microscopy, energy dispersive X-ray spectroscopy, and electron backscatter diffraction (EBSD), were employed to establish the morphological, chemical, and structural characteristics of the microstructure. The Thermo-Calc software and a Scheil–Gulliver model were used to analyze the presence and behavior of phase transformations during heating and cooling processes under non-thermodynamic equilibrium conditions, typical of AM processes. Unlike conventional TTT diagrams of this alloy, the diagram presented here reveals that the precipitation of γ′′ and δ phases occurs at lower temperatures and shorter times in AM-manufactured parts. Significantly, the superposition of γ′′ and δ phase curves in the proposed diagram underscores the interdependence between these phases. This TTT diagram is a valuable insight that can help in the development of heat treatment processes and quality control for IN718 produced via PBF-AM.