BCBaiyang Chen

Baiyang Chen

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Baiyang Chen has a total of 42 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • EBSD Analysis of AA7075-T6 Thin Sheets Butt Joints Obtained by Impulse Friction Stir Welding

    by Keqi Wang, Anton Naumov, Qibao Li, Baiyang Chen, Peihu Gao

  • Open Access

    The Effect of Heat Treatment on the Microstructure and Mechanical Properties of Plasma-Cladded CoCrFeNiMn Coatings on Compacted Graphite Iron

    by Bo Zhang, Ruitao Fu, Peihu Gao, Baiyang Chen, Anton Naumov, Fei Li, Daming Zhao, Zhong Yang, Yongchun Guo, Jianping Li, et al.

    CoCrFeNiMn high-entropy alloy coatings were deposited on compacted graphite iron (CGI) by plasma transfer arc cladding to strengthen and improve the wear resistance (performance) of the surface. The effects of different heat treatment processes on the microstructure and mechanical properties of the CoCrFeNiMn coatings were investigated. Compared with the deposited coating, the single FCC phase in the heat-treated coatings was retained, the grain size of the columnar dendrites decreased, the spacing between the dendrites increased, and the Cr-rich precipitated phase in the grain boundary increased. The heat treatment process had a positive influence on the microhardness and wear resistance of the coatings. The microhardness of the coatings increased after heat treatment. After heat treatment at 660 °C for 90 min, the coating had the highest microhardness of 563 ± 6.9 HV0.2, and it had the best wear resistance.


  • Open Access

    Effect of Heat Treatment on the Microstructure and Mechanical Properties of Plasma Cladded CoCrFeNiMn Coatings on Compacted Graphite Iron

    by Bo Zhang, Rui-Tao Fu, Pei-Hu Gao, Bai-Yang Chen, Anton Naumov, Fei Li, Da-Ming Zhao, Zhong Yang, Yong-Chun Guo, Jian-Ping Li, et al.

    CoCrFeNiMn high-entropy alloy coatings were prepared on compacted graphite iron(CGI) through plasma cladding to strength the CGI substrate. The effects of heat treatment temperatures and times on the microstructure and mechanical properties of the CoCrFeNiMn coatings were investigated. After heat treatment, a single FCC phase was remained in the coating as compared to the deposited one, with smaller dendrites, larger dendritic spacing and more Cr-rich compounds precipitated between dendrites. The coatings’ microhardness was increased after heat treatment. After heat treated at 660°C for 90 minutes, the coating had the highest microhardness of 563±6.9 HV0.2, the lowest frictional coefficient of 0.71 and the smallest wear mass loss of 1.12 mg, and it had the best wear resistance.

  • Open Access

    Microstructure and Properties of FeAlC-x(WC-Co) Composite Coating Prepared through Plasma Transfer Arc Cladding

    by Baiyang Chen, Bo Zhang, Daming Zhao, Peihu Gao, Anton Naumov, Qibao Li, Fei Li, Zhong Yang, Yongchun Guo, Jianping Li, et al.

    Tungsten carbide (WC) is widely used in wear-resistant parts due to its excellent wear resistance. Iron-based alloys are used in the repair and remanufacturing of engine components due to their good compatibility with iron-based workpieces. In order to enhance the wear resistance of engine components in service under abrasive conditions, composite coatings have been prepared for cast iron engine components by adding WC-Co to iron-based powders. This study investigates the microstructure and wear properties of composite coatings of iron-based alloys reinforced with different contents of WC particles. The composite coatings mainly contained γ-Fe, α-Fe, WC and Fe3W3C. With the addition of the WC-Co strengthening phase, the average hardness of the FeAlC-x(WC-Co) composite coatings increases from 524 HV0.2 to 814 HV0.2. Wear test results showed that when the WC addition was 20%, it had the lowest frictional coefficient of 0.5 and the lowest wear mass loss of 1.3 mg. Compared to the original Fe-based alloy coatings, the WC particle-reinforced FeAlC composite coatings display improved wear resistance on a reduced friction basis, mainly benefiting from the high wear resistance of the graphite solid lubrication phase and carbides in the cladding.


  • Open Access

    Investigation of Impact of C/Si Ratio on the Friction and Wear Behavior of Si/SiC Coatings Prepared on C/C-SiC Composites by Slurry Reaction Sintering and Chemical Vapor Infiltration

    by Daming Zhao, Kaifeng Cheng, Baiyang Chen, Peihu Gao, Qiaoqin Guo, Hao Cheng, Anton Naumov, Qiao Li, Wenjie Kang

    Carbon/carbon (C/C)-SiC composite materials have a series of outstanding advantages, such as a light weight, resistance to thermal degradation, excellent friction performance, and good stability in complex environments. In order to improve the wear resistance of the C/C-SiC composite matrix, Si/SiC coatings were prepared by a combination of chemical vapor infiltration and reactive sintering. The wear performance of Si/SiC coatings with different amounts of silicon carbide was investigated. When the carbon silicon ratio in the slurry was 1:3, the SiC particle content in the coating was 93.0 wt.%; the prepared Si/SiC coating exhibited the lowest wear rate of 3.2 × 10−3 mg·N−1·m−1 among the four coatings; and its frictional coefficient was 0.95, which was higher than that of the substrate. As the residual Si content in the coating decreased, the continuity between SiC particles in the coating was improved. Both the high hardness of SiC and the dense coating contributed significantly to enhancing the coating’s wear resistance.


  • Open Access

    Microstructure and Properties of FeAlC-x(WC-Co) Composite Coating Prepared through Plasma Transfer Arc Cladding

    by Bai-Yang Chen, Bo Zhang, Daming Zhao, Peihu Gao, Anton Naumov, Qi-Bao Li, Fei Li, Zhong Yang, Yongchun Guo, Jian-Ping Li, et al.

    Tungsten carbide (WC) was well known as a wear-resistant material. Iron-based pow-der was suitable for remanufacturing of cast iron engine parts. To improve the wear resistance of the remanufactured iron-based cast iron engine parts, WC-Co was intro-duced into iron-based powders to prepare composite coatings for cast iron engine components. In this work, FeAlC-x(WC-Co) composite coatings were prepared by plasma transfer arc on compacted graphite cast iron. The influences of WC-Co con-tents in the Fe-AlC-x(WC-Co) composite coatings on the microstructure and properties of the composite coatings were investigated. The composite coatings contained γ-Fe, α-Fe, WC and Fe3W3C mainly. The microhardness of FeAlC-x(WC-Co) composite coatings had the highest hardness of 814 HV0.2, the-lowest coefficient of 0.5 and the lest wear mass loss of 1.3mg when the weight content of WC-Co in the composite coating was 20wt%. As compared with the FeAlC coating, FeAlC-x(WC-Co) composite coating achieved the effect of reducing friction and wear resistance simultaneously, which resulted from the self-lubricating effect of graphite and high wear-resistance of carbides in the claddings.

  • Open Access

    Microstructure and Properties of Densified Gd2O3 Bulk

    by Pei-Hu Gao, Can Jin, Sheng-Cong Zeng, Rui-Guang Xie, Bo Zhang, Bai-Yang Chen, Zhong Yang, Yong-Chun Guo, Min-Xian Liang, Jian-Ping Li, et al.

    In this work, Gd2O3 bulks were sintered at temperatures ranging from 1400 °C to 1600 °C for times from 6 h to 24 h, and their microstructure and properties were studied for a wider application of materials in thermal barrier coatings. The densification of the Gd2O3 bulk reached 96.16% when it was sintered at 1600 °C for 24 h. The elastic modulus, hardness, fracture toughness and thermal conductivity of the bulks all increased with the rise in sintering temperature and extension of sintering time, while the coefficient of thermal expansion decreased. When the Gd2O3 bulk was sintered at 1600 °C for 24 h, it had the greatest elastic modulus, hardness, fracture toughness and thermal conductivity of 201.15 GPa, 9.13 GPa, 15.03 MPa·m0.5 and 2.75 W/(m·k) (at 1100 °C), respectively, as well as the smallest thermal expansion coefficients of 6.69 × 10−6/°C (at 1100 °C).


  • Open Access

    Influence of Plasma Arc Current on the Friction and Wear Properties of CoCrFeNiMn High Entropy Alloy Coatings Prepared on CGI through Plasma Transfer Arc Cladding

    by Peihu Gao, Ruitao Fu, Jilin Liu, Baiyang Chen, Bo Zhang, Daming Zhao, Zhong Yang, Yongchun Guo, Minxian Liang, Jianping Li, et al.

    High-entropy alloys receive more attention for high strength, good ductility as well as good wear resistance. In this work, CoCrFeNiMn high-entropy alloy (HEA) coatings were deposited on compacted graphite iron through plasma transfer arc at different currents. The microstructure and wear properties of the CoCrFeNiMn HEA coatings were investigated. The coatings are composed of single phase with FCC structure. The CoCrFeNiMn HEA coating had the highest microhardness of 394 ± 21.6 HV0.2 and the lowest wear mass loss when the plasma current was 65 A. All of the HEA coatings had higher friction coefficients than that of the substrate. There were adhesive, abrasive and oxidation wear forms in the HEA coatings with the wear couple of N80 alloy. The HEA coating presented higher friction coefficient and better wear resistance than compacted graphite iron.


  • Open Access

    Wear Properties of Iron-Based Alloy Coatings Prepared by Plasma Transfer Arc Cladding

    by Baiyang Chen, Peihu Gao, Bo Zhang, Daming Zhao, Wei Wang, Can Jin, Zhong Yang, Yongchun Guo, Minxian Liang, Jianping Li, et al.

    Plasma transfer arc cladding technology has been widely utilized in surface engineering, repairing and remanufacturing. In the present work, multiple cladded thick claddings were prepared on compacted graphite cast iron (CGI) substrates with iron-based powders through plasma transfer arc cladding technology using different plasma arc currents to improve the surface wear resistance. The coatings’ phase and microstructure were analysed through XRD, SEM and EDS. The coatings’ microhardness and wear resistance were characterized. There were pearlite, graphite, austenite and secondary carbides in the iron-based alloy coatings. Due to the heat influence during the multiple cladding process, a spheroidal graphite transition zone appeared between the substrate and the coating. The microhardness of the claddings varied from 363 to 402 HV as the plasma arc current was changed from 45 to 60 A. With the increase of plasma arc current, the cladding’s microhardness increased. The iron-based coating’s minimum friction coefficient and wear mass loss were about 0.48 and 4.2 mg, respectively, when the plasma arc current was 60 A, which are lower values than those of the compacted graphite iron substrate with the friction coefficient and wear mass loss of 0.55 and 8.2 mg. Compared with the substrate, the iron-based alloy claddings achieved the effect of reducing friction and wear resistance simultaneously, which resulted from the self-lubricating effect of graphite and high wear-resistance of carbides in the claddings. The iron-based coatings had a similar abrasive wear mechanism to the CGI, which should be helpful to repair or remanufacture CGI workpieces.


  • Open Access

    Mechanical Properties of Multi-Sized Porous Thermal Barrier Coatings at Micro and Nano Scales after Long-Term Service at High Temperature

    by Peihu Gao, Shengcong Zeng, Can Jin, Bo Zhang, Baiyang Chen, Zhong Yang, Yongchun Guo, Minxian Liang, Jianping Li, Wei Wang, et al.

    Atmospheric plasma-sprayed multi-sized porous structures in thermal barrier coatings (TBCs) were constructed with hollow spherical (HOSP) 8YSZ powders and polypropylene pore formers. The mechanical properties of the multi-sized TBCs were investigated through the nanoindentation method as comparations of the as-sprayed coating and those serving at 1100 °C for a long-term. The results showed that the introduction of the multi-sized pores into TBCs could lead to the decrease of the hardness and modulus as well as the increase of fracture toughness. The hardness and modulus of the coating increased, and the fracture toughness of the coating decreased with the prolongation of the serving times at high temperatures. The mechanical properties of the coating became stable after 60 days’ serving at 1100 °C. The hardness, elastic modulus and fracture toughness of the TBCs increased to 6.51, 7.79, 10.04 GPa and 126.36, 135.13, 145.22 GPa as well as 1.049, 1.157, 1.255 MPa·m0.5, respectively, corresponding to the multi-sized porous TBCs with 0%, 10% and 15% PP powders. The nano-size pores disappeared gradually in the multi-sized TBCs during serving at 1100 °C. The macropores deposited between the ceramic particles penetrated with little diffusion and were not easy to disappear. The introduction of a multi-scale pore structure into the TBCs could improve the stress-strain tolerance of the TBCs.