Eslam Abubakr
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Eslam Abubakr has a total of 43 co-authors. Here are the top co-authors by number of shared publications:
- Abdelrahman Zkria
Department of Applied Science for Electronics and Materials, Kyushu University
9 shared publications Tsuyoshi Yoshitake
8 shared publications- Tetsuo Kan
Department of Mechanical and Intelligent Systems Engineering, Graduate School of Informatics and Engineering, The University of Electro-Communications, 1-5-1 Chofugaoka, Chofu, Tokyo 182-8585, Japan
6 shared publications Hiroshi Ikenoue
Graduate School of Information Science and Electrical Engineering, Kyushu University, Fukuoka, Japan
4 shared publicationsShiro Saito
IMRA Japan Co., Ltd., Kariya, Japan
4 shared publications- Ariful Haque
Texas State University
3 shared publications
Latest Publications
- Open Access
- 17 November 2026
- Published by MDPI AG in Biosensors
- Vol. 16 (11) , 658
Filter-Array-Free Broadband NIR Reconstructive Spectroscopy via a Titanium-Engineered Self-Powered Plasmonic Photodetector
Conventional gas sensors suffer from poor selectivity, high operating temperatures, or reliance on bulky spectrometers and cooled infrared detectors, limiting compact, real-time analysis. Plasmon-induced hot-electron injection across a metal/semiconductor junction offers a route to sub-bandgap photodetection without an external bias. Here, we demonstrate an angle-resolved, filter-array-free near-infrared (NIR) reconstructive spectroscopy approach based on a single embedded-grating plasmonic photodetector. Gold supports the grating-coupled surface plasmon resonance, while a thin Ti interlayer improves the interface and yields an effective Schottky barrier height of 0.506 eV, enabling internal photoemission below the silicon bandgap. An embedded grating, formed by directly grooving the silicon surface, increases the metal/semiconductor interfacial area available for hot-electron injection. Zero-bias responsivities of 4 mA/W at 1200 nm and 0.62 mA/W at 1600 nm were measured, and resonant photoresponse was additionally observed up to 2.4 µm with high spectral selectivity. Using a measured angle–wavelength responsivity matrix, high-fidelity spectral reconstruction comparable to that of commercial Fourier-transform infrared spectrometers was demonstrated at room temperature. In the present demonstration, the detector chip requires no filter array, with high potential for compact NIR spectroscopic sensors and gas monitoring applications.
- 17 November 2026
- Published by MDPI AG in Biosensors
- Vol. 16 (11) , 658
Open AccessFilter-Array-Free Broadband NIR Reconstructive Spectroscopy via a Titanium-Engineered Self-Powered Plasmonic Photodetector
Conventional gas sensors suffer from poor selectivity, high operating temperatures, or reliance on bulky spectrometers and cooled infrared detectors, limiting compact, real-time analysis. Plasmon-induced hot-electron injection across a metal/semiconductor junction offers a route to sub-bandgap photodetection without an external bias. Here, we demonstrate an angle-resolved, filter-array-free near-infrared (NIR) reconstructive spectroscopy approach based on a single embedded-grating plasmonic photodetector. Gold supports the grating-coupled surface plasmon resonance, while a thin Ti interlayer improves the interface and yields an effective Schottky barrier height of 0.506 eV, enabling internal photoemission below the silicon bandgap. An embedded grating, formed by directly grooving the silicon surface, increases the metal/semiconductor interfacial area available for hot-electron injection. Zero-bias responsivities of 4 mA/W at 1200 nm and 0.62 mA/W at 1600 nm were measured, and resonant photoresponse was additionally observed up to 2.4 µm with high spectral selectivity. Using a measured angle–wavelength responsivity matrix, high-fidelity spectral reconstruction comparable to that of commercial Fourier-transform infrared spectrometers was demonstrated at room temperature. In the present demonstration, the detector chip requires no filter array, with high potential for compact NIR spectroscopic sensors and gas monitoring applications.
- Open Access
- 13 November 2025
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 10 (46) , 56856-56862
Au–Si Diffusion Effects on Surface Plasmon Resonance Sensor Using Internal Photoemission at Metal/Si Schottky Barrier
Surface plasmon resonance sensors based on Schottky barriers have been extensively studied for their potential to enable compact, high-performance chemical sensing. These sensors utilize gold periodic structures on n-type silicon to couple surface plasmon resonance and convert it into electrical signals via internal photoemission at the gold/silicon (Au/Si) Schottky interface. However, stability over time remains challenging, as such sensors exhibit performance degradation. In this study, we investigate the mechanisms underlying performance degradation in surface plasmon resonance sensors utilizing a Au/Si Schottky barrier, with a particular focus on atomic diffusion at the interface. Rigorous 10-day continuous measurements of a conventional Au/Si sensor demonstrated silicon atom migration to the Au surface, hindering the device operation with a drop in responsivity of over 46%. An alternative design incorporating a molybdenum diffusion barrier layer to mitigate atomic diffusion effectively suppresses both the shift in the surface plasmon resonance angle and the degradation of responsivity over time, as confirmed by SPR response measurements and spectroscopy analysis. These findings address the crucial role of Si diffusion in resonance angle shifts and performance degradation.
- 13 November 2025
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 10 (46) , 56856-56862
Open AccessAu–Si Diffusion Effects on Surface Plasmon Resonance Sensor Using Internal Photoemission at Metal/Si Schottky Barrier
Surface plasmon resonance sensors based on Schottky barriers have been extensively studied for their potential to enable compact, high-performance chemical sensing. These sensors utilize gold periodic structures on n-type silicon to couple surface plasmon resonance and convert it into electrical signals via internal photoemission at the gold/silicon (Au/Si) Schottky interface. However, stability over time remains challenging, as such sensors exhibit performance degradation. In this study, we investigate the mechanisms underlying performance degradation in surface plasmon resonance sensors utilizing a Au/Si Schottky barrier, with a particular focus on atomic diffusion at the interface. Rigorous 10-day continuous measurements of a conventional Au/Si sensor demonstrated silicon atom migration to the Au surface, hindering the device operation with a drop in responsivity of over 46%. An alternative design incorporating a molybdenum diffusion barrier layer to mitigate atomic diffusion effectively suppresses both the shift in the surface plasmon resonance angle and the degradation of responsivity over time, as confirmed by SPR response measurements and spectroscopy analysis. These findings address the crucial role of Si diffusion in resonance angle shifts and performance degradation.
- 9 September 2025
- Published by Springer Nature in MRS Communications
- Vol. 15 (6) , 1440-1444
Advanced self-powered NIR plasmonic photodetection and photoelectron spectroscopy
- 9 September 2025
- Published by Springer Nature in MRS Communications
- Vol. 15 (6) , 1440-1444
Advanced self-powered NIR plasmonic photodetection and photoelectron spectroscopy
- 17 March 2025
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 54 (5) , 4074-4082
Study on Temperature-Dependent Photoresponsivity and Stability of Mid-Infrared Photodetector Based on Si-Process-Compatible Plasmonic PtSi/p-Si Schottky Structure
- 17 March 2025
- Published by Springer Nature in Journal of Electronic Materials
- Vol. 54 (5) , 4074-4082
Study on Temperature-Dependent Photoresponsivity and Stability of Mid-Infrared Photodetector Based on Si-Process-Compatible Plasmonic PtSi/p-Si Schottky Structure
- 9 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (1) , 301-305
Advanced Room-Temperature NIR Plasmonic Photodetection and Reconstructive Spectroscopy
While Au is commonly utilized in semiconductor fabrication, its interaction with Si yields unstable contacts, posing potential reliability concerns. In this work, Cr interlayers were integrated to improve interface properties, enhance charge carrier transport within a plasmonic photodetector, and ensure long-term stability, demonstrated by consistent responses under zero bias and room-temperature conditions over the span of a year. The induced Fermi level shifts and Schottky barrier lowering to 0.59 eV, improving responsivity and extending the operation range beyond 1850 nm with increased sensitivity, allowing for precise reconstructive spectroscopy (RS). This is promising for reliable compound identification based on specific bond absorbance properties while scaling down IR spectroscopy to chip level, promoting applications like environmental monitoring and gas detection.
- 9 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 72 (1) , 301-305
Advanced Room-Temperature NIR Plasmonic Photodetection and Reconstructive Spectroscopy
While Au is commonly utilized in semiconductor fabrication, its interaction with Si yields unstable contacts, posing potential reliability concerns. In this work, Cr interlayers were integrated to improve interface properties, enhance charge carrier transport within a plasmonic photodetector, and ensure long-term stability, demonstrated by consistent responses under zero bias and room-temperature conditions over the span of a year. The induced Fermi level shifts and Schottky barrier lowering to 0.59 eV, improving responsivity and extending the operation range beyond 1850 nm with increased sensitivity, allowing for precise reconstructive spectroscopy (RS). This is promising for reliable compound identification based on specific bond absorbance properties while scaling down IR spectroscopy to chip level, promoting applications like environmental monitoring and gas detection.
- 11 March 2024
- Published by Elsevier in Optical Materials
- Vol. 150
Optimizing geometry and metal-dependent performance of Si-based Schottky plasmonic photodetectors
- 11 March 2024
- Published by Elsevier in Optical Materials
- Vol. 150
Optimizing geometry and metal-dependent performance of Si-based Schottky plasmonic photodetectors
- 4 March 2024
- Published by Optica Publishing Group in Applied Optics
- Vol. 63 (8) , 2046-2055
Characterization of an uncooled mid-infrared Schottky photodetector based on a 2D Au/PtSi/p-Si nanohole array at a higher light modulation frequency
In this study, an uncooled 2D nanohole array PtSi/p-Si Schottky mid-infrared (MIR) photodetector, which is essential for on-chip Si-based low-barrier MIR detectors, is presented. Room temperature operation introduces susceptibility to thermal noise and can impact stability. Through modulation frequency and reverse bias optimization, the stability improved by 7 times at 170 Hz and −3.5V, respectively. The effective light detection and stability were confirmed through ON/OFF response measurements over a longer time. The wavelength-dependent responsivity, measured with a tunable MIR laser, confirmed the responsiveness of the device in the MIR region of 2.5 µm to 4.0 µm, with a maximum specific detectivity (D*) of 2.0×103cmHz1/2W−1 at 3.0 µm; this result shows its potential applicability for noninvasive human lipid monitoring. Overall, this study focuses on the crucial role of signal analysis optimization in enhancing the performance of MIR photodetectors at room temperature.
- 4 March 2024
- Published by Optica Publishing Group in Applied Optics
- Vol. 63 (8) , 2046-2055
Characterization of an uncooled mid-infrared Schottky photodetector based on a 2D Au/PtSi/p-Si nanohole array at a higher light modulation frequency
In this study, an uncooled 2D nanohole array PtSi/p-Si Schottky mid-infrared (MIR) photodetector, which is essential for on-chip Si-based low-barrier MIR detectors, is presented. Room temperature operation introduces susceptibility to thermal noise and can impact stability. Through modulation frequency and reverse bias optimization, the stability improved by 7 times at 170 Hz and −3.5V, respectively. The effective light detection and stability were confirmed through ON/OFF response measurements over a longer time. The wavelength-dependent responsivity, measured with a tunable MIR laser, confirmed the responsiveness of the device in the MIR region of 2.5 µm to 4.0 µm, with a maximum specific detectivity (D*) of 2.0×103cmHz1/2W−1 at 3.0 µm; this result shows its potential applicability for noninvasive human lipid monitoring. Overall, this study focuses on the crucial role of signal analysis optimization in enhancing the performance of MIR photodetectors at room temperature.
- Open Access
- 1 August 2022
- Published by AIP Publishing in AIP Advances
- Vol. 12 (8) , 085007
Nanocarbon ohmic electrodes fabricated by coaxial arc plasma deposition for phosphorus-doped diamond electronics application
N-Type (phosphorus-doped) diamond is a promising material for diamond-based electronic devices. However, realizing good ohmic contacts for phosphorus-doped diamonds limits their applications. Thus, the search for non-conventional ohmic contacts has become a hot topic for many researchers. In this work, nanocarbon ohmic electrodes with enhanced carrier collection efficiency were deposited by coaxial arc plasma deposition. The fabricated nanocarbon ohmic electrodes were extensively examined in terms of specific contact resistance and corrosion resistance. The circular transmission line model theory was used to estimate the charge collection efficiency of the nanocarbon ohmic electrodes in terms of specific contact resistance at a specific voltage range (5–10 V); they exhibited a specific contact resistance of 1 × 10−3 Ωcm2. The result revealed one order reduction in the specific contact resistance and, consequently, a potential drop at the diamond/electrode interface compared to the conventional Ti electrodes. Moreover, the fabricated nanocarbon electrodes exhibited high mechanical adhesion and chemical inertness over repeated acid treatments. In device applications, the nanocarbon electrodes were evaluated for Ni/n-type diamond Schottky diodes, and they exhibited nearly one order enhancement in the rectification ratio and a fast charge collection at lower biasing voltages.
- 1 August 2022
- Published by AIP Publishing in AIP Advances
- Vol. 12 (8) , 085007
Open AccessNanocarbon ohmic electrodes fabricated by coaxial arc plasma deposition for phosphorus-doped diamond electronics application
N-Type (phosphorus-doped) diamond is a promising material for diamond-based electronic devices. However, realizing good ohmic contacts for phosphorus-doped diamonds limits their applications. Thus, the search for non-conventional ohmic contacts has become a hot topic for many researchers. In this work, nanocarbon ohmic electrodes with enhanced carrier collection efficiency were deposited by coaxial arc plasma deposition. The fabricated nanocarbon ohmic electrodes were extensively examined in terms of specific contact resistance and corrosion resistance. The circular transmission line model theory was used to estimate the charge collection efficiency of the nanocarbon ohmic electrodes in terms of specific contact resistance at a specific voltage range (5–10 V); they exhibited a specific contact resistance of 1 × 10−3 Ωcm2. The result revealed one order reduction in the specific contact resistance and, consequently, a potential drop at the diamond/electrode interface compared to the conventional Ti electrodes. Moreover, the fabricated nanocarbon electrodes exhibited high mechanical adhesion and chemical inertness over repeated acid treatments. In device applications, the nanocarbon electrodes were evaluated for Ni/n-type diamond Schottky diodes, and they exhibited nearly one order enhancement in the rectification ratio and a fast charge collection at lower biasing voltages.
- Open Access
- 6 June 2022
- Published by Taylor & Francis in Materials Research Letters
- Vol. 10 (10) , 666-674
Formation of p-n+diamond homojunctions by shallow doping of phosphorus through liquid emersion excimer laser irradiation
We report the fabrication of p-n+ diamond homojunction through an innovative approach of laser irradiation in liquid-ambient. A shallow phosphorus-doped layer with a high electric conductivity is processed on top of a p-type diamond substrate to form the p-n+ homojunction. The current–voltage measurements at room temperature confirmed high conductivity of the induced n+ layer and showed exceptional rectification properties with an ideality factor of 1.07, excellent low on-resistance of 3.7 × 10−2 Ωcm2, and current density over 260 Acm−2 at forward-biasing of 10 V. Furthermore, undetectable leakage-current provides a rectification ratio exceeding 1010 at ±6 V, promoting the junction in UV detection applications. GRAPHICAL ABSTRACT IMPACT STATEMENT The process allows further selective and feasible patterned/shallow doping of diamond surfaces beyond the conventional methods, with minimal power consumption and fast production rate, providing more readily electrically contacted devices.
- 6 June 2022
- Published by Taylor & Francis in Materials Research Letters
- Vol. 10 (10) , 666-674
Open AccessFormation of p-n+diamond homojunctions by shallow doping of phosphorus through liquid emersion excimer laser irradiation
We report the fabrication of p-n+ diamond homojunction through an innovative approach of laser irradiation in liquid-ambient. A shallow phosphorus-doped layer with a high electric conductivity is processed on top of a p-type diamond substrate to form the p-n+ homojunction. The current–voltage measurements at room temperature confirmed high conductivity of the induced n+ layer and showed exceptional rectification properties with an ideality factor of 1.07, excellent low on-resistance of 3.7 × 10−2 Ωcm2, and current density over 260 Acm−2 at forward-biasing of 10 V. Furthermore, undetectable leakage-current provides a rectification ratio exceeding 1010 at ±6 V, promoting the junction in UV detection applications. GRAPHICAL ABSTRACT IMPACT STATEMENT The process allows further selective and feasible patterned/shallow doping of diamond surfaces beyond the conventional methods, with minimal power consumption and fast production rate, providing more readily electrically contacted devices.