Xiaodong Pan
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Xiaodong Pan has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Guanghui Wei
National Key Laboratory on Electromagnetic Environment Effects, Army Engineering University of PLA, Shijiazhuang Campus, Shijiazhuang 050003, China
14 shared publications - Jiangning Sun
National Key Laboratory on Electromagnetic Environment Effects, Army Engineering University of PLA, Shijiazhuang Campus, Shijiazhuang 050003, China
9 shared publications - Haojiang Wan
National Key Laboratory on Electromagnetic Environment Effects, Army Engineering University, Shijiazhuang Campus, Shijiazhuang, China
6 shared publications - Hong-Ze Zhao
National Key Laboratory of Electromagnetic Environment Effects, Army Engineering University Shijiazhuang Campus, Shijiazhuang 050003, China
6 shared publications - Xinfu Lu
National Key Laboratory on Electromagnetic Environment Effects, Army Engineering University, Shijiazhuang Campus, Shijiazhuang, China
6 shared publications Guanghui Wei
National Key Laboratory on Electromagnetic Environment Effects, Army Engineering University, Shijiazhuang Campus, Shijiazhuang, People’s Republic of China
5 shared publications
Latest Publications
- Open Access
- 27 September 2025
- Published by MDPI AG in Electronics
- Vol. 14 (19) , 3842
Interference Feature of Square-Wave Modulated Single-Frequency Signal to Regulated Power Supply
To explore the advantages and limitations of employing square-wave modulated single-frequency signals in electric field radiated susceptibility testing, critical interference effect tests using both single-frequency continuous waves and square-wave modulated single-frequency radiation fields were conducted, respectively, at four susceptible frequencies (98, 262, 326, 404 MHz) of a linear voltage regulator and two susceptible frequencies (26, 36 MHz) of a switching-mode power supply. The variation law of critical interference field strength according to the modulation period was determined. The test results demonstrate that the output interruption in the tested power supplies was not only determined by the interference field strength and frequency but also significantly influenced by the repetition period of the interference signal. Square-wave modulated single-frequency interference provides superior characterization of the time-domain response characteristics of the equipment under testing when compared to conventional single-frequency continuous wave interference. However, RS103 only employs a modulated signal with a 1 ms repetition period, making it insufficient to fully characterize the actual susceptible characteristics of the tested equipment. Therefore, it requires supplementary evaluation through critical interference testing using single-frequency continuous waves.
- 27 September 2025
- Published by MDPI AG in Electronics
- Vol. 14 (19) , 3842
Open AccessInterference Feature of Square-Wave Modulated Single-Frequency Signal to Regulated Power Supply
To explore the advantages and limitations of employing square-wave modulated single-frequency signals in electric field radiated susceptibility testing, critical interference effect tests using both single-frequency continuous waves and square-wave modulated single-frequency radiation fields were conducted, respectively, at four susceptible frequencies (98, 262, 326, 404 MHz) of a linear voltage regulator and two susceptible frequencies (26, 36 MHz) of a switching-mode power supply. The variation law of critical interference field strength according to the modulation period was determined. The test results demonstrate that the output interruption in the tested power supplies was not only determined by the interference field strength and frequency but also significantly influenced by the repetition period of the interference signal. Square-wave modulated single-frequency interference provides superior characterization of the time-domain response characteristics of the equipment under testing when compared to conventional single-frequency continuous wave interference. However, RS103 only employs a modulated signal with a 1 ms repetition period, making it insufficient to fully characterize the actual susceptible characteristics of the tested equipment. Therefore, it requires supplementary evaluation through critical interference testing using single-frequency continuous waves.
- 4 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 74 (00189456) , 1-15
Equivalent Test Method for EMP Radiation Effect Into Shielded Multicore Wire
To address the significant challenges of testing the electromagnetic pulse (EMP) radiation effects on the shielded multi-core wire coupling channel in large-scale weapon systems, a theoretical model has been developed that utilizes bulk current injection (BCI) as an equivalent substitute for high-field-intensity electromagnetic radiation. This model establishes equivalence based on the equal terminal responses of each wire pair under both radiated and injected conditions. The equivalent relationship between the injection source and the radiation field intensity for each wire pair is linear and uniform. This relationship, being independent of the terminal impedance at the equipment under test (EUT), enables the calculation of the equivalent injection waveforms. The equivalent testing method for strong EMP radiation effects is proposed and demonstrated by experimental validation. The average correlation coefficient of response curves for each wire pair in the pass-through load simulating the EUT test exceeds 0.9. The maximum error observed in the airborne computer effect test is 1.48 dB. The proposed method indicates that achieving equivalence for one wire pair’s terminal response under radiated conditions ensures equivalence for the remaining wire pairs as well, demonstrating applicability to nonlinear systems.
- 4 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 74 (00189456) , 1-15
Equivalent Test Method for EMP Radiation Effect Into Shielded Multicore Wire
To address the significant challenges of testing the electromagnetic pulse (EMP) radiation effects on the shielded multi-core wire coupling channel in large-scale weapon systems, a theoretical model has been developed that utilizes bulk current injection (BCI) as an equivalent substitute for high-field-intensity electromagnetic radiation. This model establishes equivalence based on the equal terminal responses of each wire pair under both radiated and injected conditions. The equivalent relationship between the injection source and the radiation field intensity for each wire pair is linear and uniform. This relationship, being independent of the terminal impedance at the equipment under test (EUT), enables the calculation of the equivalent injection waveforms. The equivalent testing method for strong EMP radiation effects is proposed and demonstrated by experimental validation. The average correlation coefficient of response curves for each wire pair in the pass-through load simulating the EUT test exceeds 0.9. The maximum error observed in the airborne computer effect test is 1.48 dB. The proposed method indicates that achieving equivalence for one wire pair’s terminal response under radiated conditions ensures equivalence for the remaining wire pairs as well, demonstrating applicability to nonlinear systems.
- Open Access
- 1 March 2025
- Published by AIP Publishing in AIP Advances
- Vol. 15 (3)
Enhancement and optimization of absorbing performance using Chebyshev ridge structures in microwave anechoic chambers
This study explores the application of Chebyshev ridge structures in the optimization of absorbing materials within microwave anechoic chambers, aiming to enhance absorption performance and improve antenna testing accuracy by integrating Fresnel zone theory. The research employs geometric diffraction theory to analyze electromagnetic wave reflection behavior at different frequencies and optimizes the layout of absorbing materials within the chamber. Simulation results indicate that the introduction of Chebyshev ridge structures significantly reduces the reflection level in the quiet zone, with a decrease of over 10 dB across all frequency bands. The measured reflection levels and tapering in the quiet zone of the chamber constructed with this optimized design meet the requirements for far-field antenna testing. Compared to traditional designs, this optimization effectively minimizes reflection interference and reduces material costs. The findings provide a theoretical foundation and practical reference for the design and engineering application of absorbing materials in microwave anechoic chambers.
- 1 March 2025
- Published by AIP Publishing in AIP Advances
- Vol. 15 (3)
Open AccessEnhancement and optimization of absorbing performance using Chebyshev ridge structures in microwave anechoic chambers
This study explores the application of Chebyshev ridge structures in the optimization of absorbing materials within microwave anechoic chambers, aiming to enhance absorption performance and improve antenna testing accuracy by integrating Fresnel zone theory. The research employs geometric diffraction theory to analyze electromagnetic wave reflection behavior at different frequencies and optimizes the layout of absorbing materials within the chamber. Simulation results indicate that the introduction of Chebyshev ridge structures significantly reduces the reflection level in the quiet zone, with a decrease of over 10 dB across all frequency bands. The measured reflection levels and tapering in the quiet zone of the chamber constructed with this optimized design meet the requirements for far-field antenna testing. Compared to traditional designs, this optimization effectively minimizes reflection interference and reduces material costs. The findings provide a theoretical foundation and practical reference for the design and engineering application of absorbing materials in microwave anechoic chambers.
- 11 September 2024
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 35 (12) , 125107
Effect of current probe location on response law of shielded multi-core wire
Bulk current injection (BCI) is a commonly used method in electromagnetic compatibility testing. In order to enhance the injection efficiency of the current probe, the interference process into the internal core wire is analyzed. Theoretical calculations indicate that the shielded multi-core wire exhibits a frequency-selective response under BCI conditions. The peak of the terminal load response voltage occurs at frequencies corresponding to the integral multiples of half the relative length of the cable. The position of the current probe along the cable only affects the amplitude of the distributed current on the shielding layer, but not its distribution pattern. The response of the internal core wire at the resonant frequencies is positively correlated with the distribution pattern of the distributed current on the shielding layer. The probe position has a significant effect on the magnitude of the wire-to-terminal response. Placing the current probe at both ends of the cable results in high injection efficiency and significant power savings.
- 11 September 2024
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 35 (12) , 125107
Effect of current probe location on response law of shielded multi-core wire
Bulk current injection (BCI) is a commonly used method in electromagnetic compatibility testing. In order to enhance the injection efficiency of the current probe, the interference process into the internal core wire is analyzed. Theoretical calculations indicate that the shielded multi-core wire exhibits a frequency-selective response under BCI conditions. The peak of the terminal load response voltage occurs at frequencies corresponding to the integral multiples of half the relative length of the cable. The position of the current probe along the cable only affects the amplitude of the distributed current on the shielding layer, but not its distribution pattern. The response of the internal core wire at the resonant frequencies is positively correlated with the distribution pattern of the distributed current on the shielding layer. The probe position has a significant effect on the magnitude of the wire-to-terminal response. Placing the current probe at both ends of the cable results in high injection efficiency and significant power savings.
- 27 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Aerospace and Electronic Systems
- Vol. 60 (6) , 8871-8886
Double Bulk Current Injection for Radiated Susceptibility of Nonlinear Avionics With Shielded Multicore Wire
It is difficult to construct the high field electromagnetic radiation environment in a large-scale spatial for testing the radiated susceptibility (RS) of nonlinear avionics systems. And the alternative test method is required. In this article, the focus is on the shielded multi-core wire coupling channel for nonlinear avionics. The response calculation model is established for each wire pair under irradiation and double bulk current injection (DBCI) conditions. It is deduced that there is the linear equivalence between the two injection sources and the radiated field intensity, providing a basis for obtaining the equivalent injection sources and linear extrapolation. Taking practical operations into account, a calculation method is developed to determine the amplitude ratio and phase difference between the two injection sources. An equivalent test method is presented for assessing the high-field-intensity electromagnetic radiation effects of nonlinear avionics in the shielded multi-core wire coupling channel. The method is validated by simulating nonlinear avionics systems with a maximum error of less than 3 dB, which is applicable to nonlinear systems. Furthermore, the effectiveness of the method is affirmed through validation using an airborne computer.
- 27 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Aerospace and Electronic Systems
- Vol. 60 (6) , 8871-8886
Double Bulk Current Injection for Radiated Susceptibility of Nonlinear Avionics With Shielded Multicore Wire
It is difficult to construct the high field electromagnetic radiation environment in a large-scale spatial for testing the radiated susceptibility (RS) of nonlinear avionics systems. And the alternative test method is required. In this article, the focus is on the shielded multi-core wire coupling channel for nonlinear avionics. The response calculation model is established for each wire pair under irradiation and double bulk current injection (DBCI) conditions. It is deduced that there is the linear equivalence between the two injection sources and the radiated field intensity, providing a basis for obtaining the equivalent injection sources and linear extrapolation. Taking practical operations into account, a calculation method is developed to determine the amplitude ratio and phase difference between the two injection sources. An equivalent test method is presented for assessing the high-field-intensity electromagnetic radiation effects of nonlinear avionics in the shielded multi-core wire coupling channel. The method is validated by simulating nonlinear avionics systems with a maximum error of less than 3 dB, which is applicable to nonlinear systems. Furthermore, the effectiveness of the method is affirmed through validation using an airborne computer.
- 24 January 2024
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 35 (4) , 045027
Equivalent test method for continuous-wave high-field effects of aircraft equipment in four-core RVVP cable coupling channel
In situations where there is ample space, constructing a high-field electromagnetic environment for radiated susceptibility testing of aircraft equipment can be difficult. This has necessitated the need for an equivalent test method. To address this issue, the response calculation models of the internal two-core pairs under radiation and injection conditions are established for the coupling channel of the four-core RVVP cable. The equivalent linear relationships between the two injected sources and the field intensity are derived, providing the foundation for obtaining equivalent injection sources and conducting linear extrapolation. Building on these findings, a specific equivalent test technology is proposed, based on the double bulk current injection. This technology is then verified through a pass-through load test for the continuous-wave high-field effects of aircraft equipment in the four-core RVVP cable coupling channel. The results of the tests demonstrated that the equivalent test method can accurately equate the high-field effects test with a maximum error of less than 1 dB. Moreover, it is applicable to nonlinear systems.
- 24 January 2024
- Published by IOP Publishing in Measurement Science and Technology
- Vol. 35 (4) , 045027
Equivalent test method for continuous-wave high-field effects of aircraft equipment in four-core RVVP cable coupling channel
In situations where there is ample space, constructing a high-field electromagnetic environment for radiated susceptibility testing of aircraft equipment can be difficult. This has necessitated the need for an equivalent test method. To address this issue, the response calculation models of the internal two-core pairs under radiation and injection conditions are established for the coupling channel of the four-core RVVP cable. The equivalent linear relationships between the two injected sources and the field intensity are derived, providing the foundation for obtaining equivalent injection sources and conducting linear extrapolation. Building on these findings, a specific equivalent test technology is proposed, based on the double bulk current injection. This technology is then verified through a pass-through load test for the continuous-wave high-field effects of aircraft equipment in the four-core RVVP cable coupling channel. The results of the tests demonstrated that the equivalent test method can accurately equate the high-field effects test with a maximum error of less than 1 dB. Moreover, it is applicable to nonlinear systems.
- 1 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 73 (00189456) , 1-11
Equivalent Measurement Method for High-Field-Intensity Radiation Sensitivity of Two-Wire Interconnection System
Under laboratory conditions, it is challenging to perform the high-field-intensity radiation sensitivity measurement on the two-wire coupled channel of the equipment under test (EUT), and the current equivalent measurement method is useless for nonlinear systems. The calculation is performed by building the response calculation model of the EUT under radiation and injection circumstances. The linear correspondence between the injection source and the radiation field is determined on the basis of utilizing a high-linearity current probe with a primary turn larger than 1. The equivalent measurement method for high-field-intensity radiation sensitivity of the two-wire interconnection system is optimized, and the nonlinear EUT can also be applied, which is closer to the actual situation under the radiation conditions and simplifies the operation steps. The CST software and the laser distance measurement sensor test are verified, and the test errors are less than 3 dB, which complies with the engineering requirements.
- 1 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 73 (00189456) , 1-11
Equivalent Measurement Method for High-Field-Intensity Radiation Sensitivity of Two-Wire Interconnection System
Under laboratory conditions, it is challenging to perform the high-field-intensity radiation sensitivity measurement on the two-wire coupled channel of the equipment under test (EUT), and the current equivalent measurement method is useless for nonlinear systems. The calculation is performed by building the response calculation model of the EUT under radiation and injection circumstances. The linear correspondence between the injection source and the radiation field is determined on the basis of utilizing a high-linearity current probe with a primary turn larger than 1. The equivalent measurement method for high-field-intensity radiation sensitivity of the two-wire interconnection system is optimized, and the nonlinear EUT can also be applied, which is closer to the actual situation under the radiation conditions and simplifies the operation steps. The CST software and the laser distance measurement sensor test are verified, and the test errors are less than 3 dB, which complies with the engineering requirements.
- 8 December 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electromagnetic Compatibility
- Vol. 65 (1) , 69-78
Evaluation Method of Noise Electromagnetic Radiation Interference Effect
In order to evaluate the viability of frequency equipment in complex electromagnetic environment, the electromagnetic radiation effect evaluation model of random noise is established based on the analysis of the blocking effect mechanism of frequency equipment. Through MATLAB calculation, the corresponding relationship table between the ratio of the critical interference field strength effective value of single frequency continuous wave and sinusoidal amplitude modulation wave and the key parameters of the model is given, and the prediction method of noise electromagnetic interference of frequency equipment is proposed. Taking a Beidou navigation receiver as the test object, the accuracy of the noise electromagnetic radiation blocking effect model is verified by single frequency continuous wave, random noise and narrowband noise electromagnetic radiation blocking effect test, and the maximum error is only 1.51 dB, which indicates that the model and prediction method proposed in this article can accurately evaluate and predict the electromagnetic radiation interference of random noise.
- 8 December 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electromagnetic Compatibility
- Vol. 65 (1) , 69-78
Evaluation Method of Noise Electromagnetic Radiation Interference Effect
In order to evaluate the viability of frequency equipment in complex electromagnetic environment, the electromagnetic radiation effect evaluation model of random noise is established based on the analysis of the blocking effect mechanism of frequency equipment. Through MATLAB calculation, the corresponding relationship table between the ratio of the critical interference field strength effective value of single frequency continuous wave and sinusoidal amplitude modulation wave and the key parameters of the model is given, and the prediction method of noise electromagnetic interference of frequency equipment is proposed. Taking a Beidou navigation receiver as the test object, the accuracy of the noise electromagnetic radiation blocking effect model is verified by single frequency continuous wave, random noise and narrowband noise electromagnetic radiation blocking effect test, and the maximum error is only 1.51 dB, which indicates that the model and prediction method proposed in this article can accurately evaluate and predict the electromagnetic radiation interference of random noise.
- Open Access
- 13 November 2022
- Published by MDPI AG in Electronics
- Vol. 11 (22) , 3722
Study on the Law and Mechanism of the Third-Order Intermodulation False Alarm Effect of the Stepped Frequency Ranging Radar
In order to improve the radar’s electromagnetic protection ability, it is essential to master the law of the false alarm effect of the radar’s out-of-band third-order intermodulation electromagnetic radiation, starting from the circuit field-circuit coupling mechanism, and the mechanism of the third-order intermodulation false alarm effect is analyzed. Taking a stepped frequency ranging radar as the research object, the absolute level value of the false alarm signal is selected as the sensitive criterion of the false alarm effect. The dual-frequency electromagnetic false alarm interference effect is carried out by using the method of the differential mode injection equivalent substitution electromagnetic radiation. The results show that the dual-frequency electromagnetic interference will cause the radar to generate the third-order intermodulation false alarm signal with the random position and waveform spreading. Under a certain interference intensity, the level of the third-order intermodulation false alarm signal increases with the increase of the interference field strength. With the continuous increase of the interference field strength, the fifth-order intermodulation false alarm signal gradually appears. The imaging mechanism, the waveform characteristics, and the level change law of the fifth-order intermodulation false alarm target, are similar to the third-order intermodulation false alarm target, and its position is also random. The maximum third-order intermodulation false alarm signal can reach 18 dBmV, indicating that the radar is sensitive to the out-of-band intermodulation electromagnetic interference.
- 13 November 2022
- Published by MDPI AG in Electronics
- Vol. 11 (22) , 3722
Open AccessStudy on the Law and Mechanism of the Third-Order Intermodulation False Alarm Effect of the Stepped Frequency Ranging Radar
In order to improve the radar’s electromagnetic protection ability, it is essential to master the law of the false alarm effect of the radar’s out-of-band third-order intermodulation electromagnetic radiation, starting from the circuit field-circuit coupling mechanism, and the mechanism of the third-order intermodulation false alarm effect is analyzed. Taking a stepped frequency ranging radar as the research object, the absolute level value of the false alarm signal is selected as the sensitive criterion of the false alarm effect. The dual-frequency electromagnetic false alarm interference effect is carried out by using the method of the differential mode injection equivalent substitution electromagnetic radiation. The results show that the dual-frequency electromagnetic interference will cause the radar to generate the third-order intermodulation false alarm signal with the random position and waveform spreading. Under a certain interference intensity, the level of the third-order intermodulation false alarm signal increases with the increase of the interference field strength. With the continuous increase of the interference field strength, the fifth-order intermodulation false alarm signal gradually appears. The imaging mechanism, the waveform characteristics, and the level change law of the fifth-order intermodulation false alarm target, are similar to the third-order intermodulation false alarm target, and its position is also random. The maximum third-order intermodulation false alarm signal can reach 18 dBmV, indicating that the radar is sensitive to the out-of-band intermodulation electromagnetic interference.
- Open Access
- 20 October 2022
- Published by Hindawi Limited in International Journal of Antennas and Propagation
- Vol. 2022, 1-14
Generation Mechanism and Characteristic Analysis of Dual-Frequency Pseudo-Signal Interference of the Swept-Frequency Radar
In order to master the law of the pseudo-signal interference effect of dual-frequency electromagnetic radiation in typical radar equipment, a certain type of Ku-band swept-frequency ranging radar was used as the test object to carry out single-frequency continuous wave and dual-frequency continuous wave pseudo-signal interference effect experiments. Through experiments, it is found that dual-frequency electromagnetic radiation will cause hill and spike type pseudo-signal interference to the swept-frequency radar. Based on the frequency analysis of the radar receiving circuit, the interference mechanism of the dual-frequency pseudo-signal is revealed, and the morphological characteristics and distance law of the pseudo-signal are explained. The variation law of the pseudo-signal level with interference field strength is obtained. The results show that the in-band dual-frequency nonintermodulation interference is similar to the single-frequency interference, and the only difference is that the number of pseudo-signals increases; when the interference frequency difference is about 400600MHz, the out-of-band dual-frequency second-order intermodulation signal will cause hill type pseudo-signal interference, and the pseudo-signal distance is random; when the interference frequency difference is less than 5MHz, both the dual-frequency second-order intermodulation signal and the third-order intermodulation signal will cause spike pseudo-signal interference inside and outside the radar operating frequency band; the pseudo-signal distance is fixed.
- 20 October 2022
- Published by Hindawi Limited in International Journal of Antennas and Propagation
- Vol. 2022, 1-14
Open AccessGeneration Mechanism and Characteristic Analysis of Dual-Frequency Pseudo-Signal Interference of the Swept-Frequency Radar
In order to master the law of the pseudo-signal interference effect of dual-frequency electromagnetic radiation in typical radar equipment, a certain type of Ku-band swept-frequency ranging radar was used as the test object to carry out single-frequency continuous wave and dual-frequency continuous wave pseudo-signal interference effect experiments. Through experiments, it is found that dual-frequency electromagnetic radiation will cause hill and spike type pseudo-signal interference to the swept-frequency radar. Based on the frequency analysis of the radar receiving circuit, the interference mechanism of the dual-frequency pseudo-signal is revealed, and the morphological characteristics and distance law of the pseudo-signal are explained. The variation law of the pseudo-signal level with interference field strength is obtained. The results show that the in-band dual-frequency nonintermodulation interference is similar to the single-frequency interference, and the only difference is that the number of pseudo-signals increases; when the interference frequency difference is about 400600MHz, the out-of-band dual-frequency second-order intermodulation signal will cause hill type pseudo-signal interference, and the pseudo-signal distance is random; when the interference frequency difference is less than 5MHz, both the dual-frequency second-order intermodulation signal and the third-order intermodulation signal will cause spike pseudo-signal interference inside and outside the radar operating frequency band; the pseudo-signal distance is fixed.