Piotr Vasiljev
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Piotr Vasiljev has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Dalius Mažeika
Department of Information Systems, Vilnius Gediminas Technical University, Sauletekio al. 11, LT-10223 Vilnius, Lithuania
2 shared publications - Andrius Čeponis
Institute of Mechanical Science, Faculty of Mechanics, Vilnius Gediminas Technical University, Plytinės Str. 25, LT-10105 Vilnius, Lithuania
1 shared publication - Jianmin Qiu
Precision Driving Laboratory, Nanjing University of Aeronautics and Astronautics, 29 YuDao street, Nanjing, China, Nanjing, 210016, CHINA
1 shared publication - Sergejus Borodinas
Department of Applied Mechanics, Vilnius Gediminas Technical University, Saulėtekis Avenue 11, 10223 Vilnius, Lithuania
1 shared publication - Xin Hong
State Key Laboratory of Mechanics and Control of Mechanical Structures, College of Aerospace Engineering, Nanjing University of Aeronautics and Astronautics, 29 Yudao Street, Nanjing 210016, China
1 shared publication - Ying Yang
State Key Laboratory of Mechanics and Control for Aerospace Structures, College of Aerospace Engineering, Nanjing University of Aeronautics and Astronautics, Yudao 29, Nanjing 210016, PR China
1 shared publication
Latest Publications
- Open Access
- 8 March 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (5) , 2386
A Disc-Type High Speed Rotary Ultrasonic Motor with Internal Contact Teeth
This paper presents a disc-type ultrasonic piezoelectric motor, which is designed for micro flying vehicles. It provides a high output rotation speed under low operating voltage, compared with common piezoelectric devices, by employing a “contact teeth” wave transmission structure. The ultrasonic motor (USM) consists of a trimorph disc stator, with triple internal contact teeth, a shaft and two hemispheric hard-wearing rotors. The operating principle of the USM is based on the superposition of the in-plane B03 vibration mode of the trimorph disc, and the first longitudinal vibration of the contact teeth. An optimization method of the stator structure parameters was proposed and validated by numerical modeling. The diameter and thickness of the stator are 20 mm and 1 mm, respectively. A prototype with the weight of 2 g was made for this experimental test. The optimal frequency of the excitation signal and the preload force are 98.5 kHz and 0.5 N, respectively. The minimum operating voltage was tested under 7.5 V and reached the speed of 225 rpm, and the maximum unloaded rotational speed of the USM reached 5172 rpm when 30 V driving voltage was applied. The maximum lifting force generated by this USM was measured as 46.1 mN, which is 2.35 times bigger than its weight.
- 8 March 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (5) , 2386
Open AccessA Disc-Type High Speed Rotary Ultrasonic Motor with Internal Contact Teeth
This paper presents a disc-type ultrasonic piezoelectric motor, which is designed for micro flying vehicles. It provides a high output rotation speed under low operating voltage, compared with common piezoelectric devices, by employing a “contact teeth” wave transmission structure. The ultrasonic motor (USM) consists of a trimorph disc stator, with triple internal contact teeth, a shaft and two hemispheric hard-wearing rotors. The operating principle of the USM is based on the superposition of the in-plane B03 vibration mode of the trimorph disc, and the first longitudinal vibration of the contact teeth. An optimization method of the stator structure parameters was proposed and validated by numerical modeling. The diameter and thickness of the stator are 20 mm and 1 mm, respectively. A prototype with the weight of 2 g was made for this experimental test. The optimal frequency of the excitation signal and the preload force are 98.5 kHz and 0.5 N, respectively. The minimum operating voltage was tested under 7.5 V and reached the speed of 225 rpm, and the maximum unloaded rotational speed of the USM reached 5172 rpm when 30 V driving voltage was applied. The maximum lifting force generated by this USM was measured as 46.1 mN, which is 2.35 times bigger than its weight.
- Open Access
- 21 July 2020
- Published by MDPI AG in Applied Sciences
- Vol. 10 (14) , 5022
Flat Cross-Shaped Piezoelectric Rotary Motor
A numerical and experimental investigation of a flat, cross-shaped piezoelectric rotary motor is presented. The design and configuration of the motor allow it to be mounted directly to the printed circuit board or integrated into the other system where mounting space is limited. The design of the motor is based on the cross-shaped stator with 16 piezo ceramic plates, which are glued on it. The rotor is placed at the center of the stator and consists of two hemispheres, a shaft, and a preloading spring. Special clamping of the stator was developed as well. It consists of four V-shaped beam structures that allow it to rigidly clamp the stator with reduced damping effect to vibrations. The operation principle of the motor is based on the first in-plane bending mode of the cross-shaped stator. The motor excitation is performed through four harmonic signals, which have a phase difference of π/2. A numerical investigation of the motor was conducted to optimize the geometrical parameters of the stator and to analyze the displacement characteristics of the contacting point. The prototype of the motor was made, and the electrical, as well as rotation speed characteristics of the motor, were measured. The results of the experimental investigation showed that the motor is able to provide a maximum rotation speed of 972.62 RPM at 200 Vp-p when the preload force of 22.65 mN was applied.
- 21 July 2020
- Published by MDPI AG in Applied Sciences
- Vol. 10 (14) , 5022
Open AccessFlat Cross-Shaped Piezoelectric Rotary Motor
A numerical and experimental investigation of a flat, cross-shaped piezoelectric rotary motor is presented. The design and configuration of the motor allow it to be mounted directly to the printed circuit board or integrated into the other system where mounting space is limited. The design of the motor is based on the cross-shaped stator with 16 piezo ceramic plates, which are glued on it. The rotor is placed at the center of the stator and consists of two hemispheres, a shaft, and a preloading spring. Special clamping of the stator was developed as well. It consists of four V-shaped beam structures that allow it to rigidly clamp the stator with reduced damping effect to vibrations. The operation principle of the motor is based on the first in-plane bending mode of the cross-shaped stator. The motor excitation is performed through four harmonic signals, which have a phase difference of π/2. A numerical investigation of the motor was conducted to optimize the geometrical parameters of the stator and to analyze the displacement characteristics of the contacting point. The prototype of the motor was made, and the electrical, as well as rotation speed characteristics of the motor, were measured. The results of the experimental investigation showed that the motor is able to provide a maximum rotation speed of 972.62 RPM at 200 Vp-p when the preload force of 22.65 mN was applied.