Priyanka P. Rade
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Priyanka P. Rade has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Baijayantimala Garnaik
Polymer Science and Engineering Division, CSIR-National Chemical Laboratory, Dr. Homi Bhabha Road, Pune 411008, India
1 shared publication Bharat Kale
Electronics Packaging Division Centre for Materials for Electronics Technology (C‐MET) Pune India
1 shared publicationRanjit Hawaldar
Electronics Packaging Division Centre for Materials for Electronics Technology (C‐MET) Pune India
1 shared publicationShany Joseph
Electronics Packaging Division Centre for Materials for Electronics Technology (C‐MET) Pune India
1 shared publicationShubhangi Swami
Electronics Packaging Division Centre for Materials for Electronics Technology (C‐MET) Pune India
1 shared publicationVarsha Pawane
Electronics Packaging Division Centre for Materials for Electronics Technology (C‐MET) Pune India
1 shared publication
Latest Publications
- 26 February 2024
- Published by Wiley in Polymer Engineering & Science
- Vol. 64 (5) , 2202-2213
Effect of functionality of diluents on digital light processing (DLP) based three‐dimensional (3D) printing of UV‐curable bisphenol A‐based epoxy acrylate resin
Digital light processing (DLP) based three‐dimensional (3D) printing technology which uses photocurable resin has been a center of interest due to its printing accuracy and printing speed. In our research, we have synthesized and modified the bisphenol A‐based epoxy acrylate resin for the DLP 3D printer having a printing accuracy of 50 μm. As the viscosity plays an important role in printing accuracy, the resin was modified with mono‐functional, di‐functional, tri‐functional, and combination of di‐tri functional acrylate diluents as well as with photoinitiator to achieve the desired level of viscosity. The process parameters like curing time and intensity were optimized using the DLP 3D printer. The uncured and UV‐cured samples were characterized using FTIR‐ATR, 1 HNMR, UV–VISIBLE, and TGA techniques. The analysis of the uncured and UV‐cured samples was carried out using viscosity, gel content, water absorption, and chemical resistance test. The mechanical properties of the UV‐cured samples were determined using hardness and tensile strength test. The 3D‐printed samples were observed under high‐resolution microscope to confirm the printing quality and resolution. The resulting outcome confirmed that the proper selection of diluents is an important parameter for achieving the good quality and resolution of samples printed using the DLP 3D printer technology. Highlights: Synthesis and modification of UV‐curable resin Selection of diluents for controlling the processablility of UV‐curable resin Optimization of process parameters for DLP based 3D printer 3D printing of samples having good quality, resolution and feature size.
- 26 February 2024
- Published by Wiley in Polymer Engineering & Science
- Vol. 64 (5) , 2202-2213
Effect of functionality of diluents on digital light processing (DLP) based three‐dimensional (3D) printing of UV‐curable bisphenol A‐based epoxy acrylate resin
Digital light processing (DLP) based three‐dimensional (3D) printing technology which uses photocurable resin has been a center of interest due to its printing accuracy and printing speed. In our research, we have synthesized and modified the bisphenol A‐based epoxy acrylate resin for the DLP 3D printer having a printing accuracy of 50 μm. As the viscosity plays an important role in printing accuracy, the resin was modified with mono‐functional, di‐functional, tri‐functional, and combination of di‐tri functional acrylate diluents as well as with photoinitiator to achieve the desired level of viscosity. The process parameters like curing time and intensity were optimized using the DLP 3D printer. The uncured and UV‐cured samples were characterized using FTIR‐ATR, 1 HNMR, UV–VISIBLE, and TGA techniques. The analysis of the uncured and UV‐cured samples was carried out using viscosity, gel content, water absorption, and chemical resistance test. The mechanical properties of the UV‐cured samples were determined using hardness and tensile strength test. The 3D‐printed samples were observed under high‐resolution microscope to confirm the printing quality and resolution. The resulting outcome confirmed that the proper selection of diluents is an important parameter for achieving the good quality and resolution of samples printed using the DLP 3D printer technology. Highlights: Synthesis and modification of UV‐curable resin Selection of diluents for controlling the processablility of UV‐curable resin Optimization of process parameters for DLP based 3D printer 3D printing of samples having good quality, resolution and feature size.
- 30 June 2020
- Published by Taylor & Francis in International Journal of Polymer Analysis and Characterization
- Vol. 25 (5) , 283-299
Synthesis and characterization of biocompatible poly (L-lactide) using zinc (II) salen complex
A biocompatible zinc (II) complex based on a tetradentate N,N,O,O-type salen ligand was synthesized, characterized and used for the solvent-free ring-opening polymerization (ROP) of L-lactide in bulk at 180 °C to prepare high molecular weight poly(L-lactide) (Mn: 82,600 Da; Mw: 140,000 Da; PDI: 1.70). Poly(L-lactide) (PLLA) was characterized using FTIR, 1H NMR, 13C NMR, GPC, TGA, DSC, WAXD, and MALDI-ToF. Kinetic measurement was carried out and first-order behavior to monomer was observed. The kapp was found as 6 ± 0.001 × 10−4 s−1. The biocompatibility of the PLLA was confirmed by in vitro cytotoxicity against NIH/3T3 fibroblast cell line and can be used in biomedical applications.
- 30 June 2020
- Published by Taylor & Francis in International Journal of Polymer Analysis and Characterization
- Vol. 25 (5) , 283-299
Synthesis and characterization of biocompatible poly (L-lactide) using zinc (II) salen complex
A biocompatible zinc (II) complex based on a tetradentate N,N,O,O-type salen ligand was synthesized, characterized and used for the solvent-free ring-opening polymerization (ROP) of L-lactide in bulk at 180 °C to prepare high molecular weight poly(L-lactide) (Mn: 82,600 Da; Mw: 140,000 Da; PDI: 1.70). Poly(L-lactide) (PLLA) was characterized using FTIR, 1H NMR, 13C NMR, GPC, TGA, DSC, WAXD, and MALDI-ToF. Kinetic measurement was carried out and first-order behavior to monomer was observed. The kapp was found as 6 ± 0.001 × 10−4 s−1. The biocompatibility of the PLLA was confirmed by in vitro cytotoxicity against NIH/3T3 fibroblast cell line and can be used in biomedical applications.