Gerald Pilz
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Gerald Pilz has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Gerald Pinter
Chair of Materials Science and Testing of Polymers, Montanuniversitaet Leoben, Leoben, Austria
2 shared publications Florian Oesterreicher
Chair of Materials Science and Testing of Polymers, Montanuniversitaet Leoben, Leoben, Austria
1 shared publicationMatthias Morak
Polymer Competence Center Leoben GmbH, Leoben, Austria
1 shared publicationPeter Guttmann
Chair of Materials Science and Testing of Polymers, Montanuniversitaet Leoben, Leoben, Austria
1 shared publicationStefan Wurzer
Chair of Materials Science and Testing of Polymers, Montanuniversitaet Leoben, Leoben, Austria
1 shared publication
Latest Publications
- Open Access
- 27 August 2021
- Published by Springer Nature in Mechanics of Time-Dependent Materials
- Vol. 26 (4) , 775-790
Assessment of the stepped isothermal method for accelerated creep testing of high-density polyethylene
Thermoplastic materials are increasingly used in demanding structural applications under, in some cases, long-term static loading over several decades. In this regard, the stepped isothermal method (SIM) with creep testing at stepwise increased temperature levels in combination with time-temperature superposition (TTSP) provides a very time efficient procedure for long-term creep characterization. In the present study, the creep behavior of an injection molded high-density polyethylene material (HDPE) was investigated by SIM in the thermally untreated state as well as after annealing.Due to experimental issues regarding the heating behavior of the specimens and non-linear viscoelastic behavior, particularly at elevated temperatures, bi-directional curve shifting was required in order to generate meaningful master curves for creep compliance. In a first step, an Arrhenius equation was used for the horizontal curve shifting, based on activation energies, determined in additional multi-frequency dynamic mechanical analysis (DMA). Continuous master curves were then obtained by empirical vertical shifting of the individual creep curve segments for the different temperature levels. In general, good agreement was observed between the resulting SIM master curves and the corresponding conventionally measured creep compliance curves at least for a time range up to 300 hours. Furthermore, significant differences in the creep tendency of the annealed material state compared to the thermally untreated condition revealed the distinct influence of the thermal history on the resulting creep behavior.
- 27 August 2021
- Published by Springer Nature in Mechanics of Time-Dependent Materials
- Vol. 26 (4) , 775-790
Open AccessAssessment of the stepped isothermal method for accelerated creep testing of high-density polyethylene
Thermoplastic materials are increasingly used in demanding structural applications under, in some cases, long-term static loading over several decades. In this regard, the stepped isothermal method (SIM) with creep testing at stepwise increased temperature levels in combination with time-temperature superposition (TTSP) provides a very time efficient procedure for long-term creep characterization. In the present study, the creep behavior of an injection molded high-density polyethylene material (HDPE) was investigated by SIM in the thermally untreated state as well as after annealing.Due to experimental issues regarding the heating behavior of the specimens and non-linear viscoelastic behavior, particularly at elevated temperatures, bi-directional curve shifting was required in order to generate meaningful master curves for creep compliance. In a first step, an Arrhenius equation was used for the horizontal curve shifting, based on activation energies, determined in additional multi-frequency dynamic mechanical analysis (DMA). Continuous master curves were then obtained by empirical vertical shifting of the individual creep curve segments for the different temperature levels. In general, good agreement was observed between the resulting SIM master curves and the corresponding conventionally measured creep compliance curves at least for a time range up to 300 hours. Furthermore, significant differences in the creep tendency of the annealed material state compared to the thermally untreated condition revealed the distinct influence of the thermal history on the resulting creep behavior.
- Open Access
- 30 July 2020
- Published by Springer Nature in Mechanics of Time-Dependent Materials
- Vol. 24 (4) , 421-433
Experimental method for creep characterization of polymeric foam materials in media immersion
Polymeric flexible foam materials are widely used as damping materials in structural applications primarily to reduce unwanted system vibrations and related noise generation. Due to the viscoelastic nature of polymers and high compressibility of soft polymeric foams, their damping quality is strongly dependent on the overall loading situation, which occasionally means complex mechanical loading scenarios combined with specific ambient service conditions. In the case of superimposed constant compressive loading the deformation of the damping components is basically dependent on the fundamental creep tendency of certain material type and is also strongly influenced by service temperature and the surrounding contact media. Thus the chosen test methodology for proper creep characterization has to reflect these major influencing parameters.In this regard, a specific creep testing device was built up for the performance of small load compression creep experiments on soft foam specimens immersed in liquid media, which was mineral oil in the present study. Moreover, the thermo-mechanical behavior of the foam materials was investigated by dynamic-mechanical analysis (DMA). The resulting temperature-dependent modulus and damping characteristics showed a good correlation with the corresponding creep behavior, enabling a rough estimation of the creep tendency within corresponding temperature ranges.
- 30 July 2020
- Published by Springer Nature in Mechanics of Time-Dependent Materials
- Vol. 24 (4) , 421-433
Open AccessExperimental method for creep characterization of polymeric foam materials in media immersion
Polymeric flexible foam materials are widely used as damping materials in structural applications primarily to reduce unwanted system vibrations and related noise generation. Due to the viscoelastic nature of polymers and high compressibility of soft polymeric foams, their damping quality is strongly dependent on the overall loading situation, which occasionally means complex mechanical loading scenarios combined with specific ambient service conditions. In the case of superimposed constant compressive loading the deformation of the damping components is basically dependent on the fundamental creep tendency of certain material type and is also strongly influenced by service temperature and the surrounding contact media. Thus the chosen test methodology for proper creep characterization has to reflect these major influencing parameters.In this regard, a specific creep testing device was built up for the performance of small load compression creep experiments on soft foam specimens immersed in liquid media, which was mineral oil in the present study. Moreover, the thermo-mechanical behavior of the foam materials was investigated by dynamic-mechanical analysis (DMA). The resulting temperature-dependent modulus and damping characteristics showed a good correlation with the corresponding creep behavior, enabling a rough estimation of the creep tendency within corresponding temperature ranges.
- 1 January 2017
- Published by Narr Francke Attempto Verlag GmbH + Co. KG
- p. 65-80
Glossar
Die Titel der neuen gelben Reihe fassen die wichtigsten Lern- und Prüfungsinhalte im Bachelor-Studium zusammen. Kompakt und leicht verständlich vermitteln sie Wirtschaftsstudenten das notwendige Wissen und fördern das Verständnis durch zahlreiche Aufgaben und Definitionen. Ideal zur Prüfungsvorbereitung oder zum Selbststudium.
- 1 January 2017
- Published by Narr Francke Attempto Verlag GmbH + Co. KG
- p. 65-80
Glossar
Die Titel der neuen gelben Reihe fassen die wichtigsten Lern- und Prüfungsinhalte im Bachelor-Studium zusammen. Kompakt und leicht verständlich vermitteln sie Wirtschaftsstudenten das notwendige Wissen und fördern das Verständnis durch zahlreiche Aufgaben und Definitionen. Ideal zur Prüfungsvorbereitung oder zum Selbststudium.
- 15 July 2015
- Published by utb GmbH
Brückenkurs Controlling
- 18 February 2015
- Published by utb GmbH
Brückenkurs Bilanzierung