Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Bettina Camin has a total of 83 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Impact of Hot Isostatic Pressing of Raw CMSX-4 on Interdiffusion and Kirkendall Porosity in Ni/CMSX-4 Diffusion Couple

    by Ahmadreza Riyahi Khorasgani, Bettina Camin, Julia Kundin

    This work presents experimental and computational research on the influence of hot isostatic pressing (HIP) of CMSX-4, a second-generation single-crystal nickel-based superalloy, on interdiffusion behavior and the formation of Kirkendall voids in subsequently assembled diffusion couples under isothermal annealing. Two sets of Ni/CMSX-4 diffusion couples were prepared: one using CMSX-4 that had undergone HIP treatment, and the other using CMSX-4 in the as-cast condition. The diffusion couples were annealed at 1250 °C for 144 h. Experimentally measured interdiffusion profiles of all alloying elements, together with synchrotron X-ray 3D μ-tomography of Kirkendall voids, were compared with calculated diffusion profiles and phase-field simulations of void evolution. A direct comparison between the simulation and experimental results enables an explanation of the HIP effect on the density, distribution, and size of the voids, as well as on the observed shifts in the interdiffusion profiles.

  • Open Access

    Modeling vacancy-induced porosity in compositionally-graded complex alloys

    by Julia Kundin, Ahmadreza Riyahi Khorasgani, Raphael Schiedung, Bettina Camin, Ingo Steinbach


  • Open Access

    The Effect of Specimen Size and Test Procedure on the Creep Behavior of ME21 Magnesium Alloy

    by Bettina Camin, Maximilian Gille

    Lightweight constructions and materials offer the opportunity to reduce CO2 emissions in the transport sector. As components in vehicles are often exposed to higher temperatures above 40% of the melting temperature, there is a risk of creep. The creep behavior usually is investigated based on standard procedures. However, lightweight constructions frequently have dimensions not adequately represented by standardized specimen geometries. Therefore, comparative creep experiments on non-standardized miniature and standardized specimens are performed. Due to a modified test procedure specified by a miniature creep device, only the very first primary creep stage shows a minor influence, but subsequently, no effect on the creep process is detected. The creep behavior of hot extruded and heat treated ME21 magnesium alloy is investigated. It is observed that the creep parameters determined by the miniature and standard creep tests are different. As the deviations are systematic, qualitatively, evidence of the creep behavior is achieved. The creep parameters obtained, and particularly the creep strain and the strain rate, show a higher creep resistance of the miniature specimen. An initial higher number of twinned grains and possible multiaxiality in the gauge volume of the miniature specimen can be responsible.


  • Open Access

    Refinement and Experimental Validation of a Vacancy Model of Pore Annihilation in Single‐Crystal Nickel‐Base Superalloys during Hot Isostatic Pressing

    by Alexander Epishin, Bettina Camin, Lennart Hansen, Marek Heuser, Inmaculada Lopez-Galilea, Benjamin Ruttert, Werner Theisen, Bernard Fedelich

    Initially, as‐cast and homogenized single crystals of nickel‐base superalloy CMSX‐4 are subjected to hot isostatic pressing at 1288 °C. Two series of experiments are conducted: under the same pressure of 103 MPa but with different durations, between 0.5 and 6 h, and under different pressures, between 15 and 150 MPa, but for the same time of 0.5 h. The porosity annihilation is investigated metallographically and by high‐resolution synchrotron X‐ray tomography. The obtained experimental results are compared with the predictions of the vacancy model proposed recently in the group. Herein, the model is further refined by coupling with X‐ray tomography. The model describes the evolution of the pore arrays enclosed in the 3D synchrotron tomograms during hot isostatic pressing and properly predicts the time and stress dependences of the pore annihilation kinetics. The validated model and the obtained experimental results are used for selecting the optimal technological parameters such as applied pressure and processing time.


  • Interdiffusion in CMSX-4 Related Ni-Base Alloy System at a Supersolvus Temperature

    by Alexander Epishin, Anton Chyrkin, Bettina Camin, Romain Saillard, Sophie Gouy, Bernard Viguier

    Interdiffusion in Ni-base superalloy CMSX-4 and alloys related to CMSX-4 was investigated at the temperature 1288 °C, which is 8 °C above the γ’-solvus temperature of this superalloy, 1280 °C. This temperature is of a special interest because it is a temperature of hot isostatic pressing applied to CMSX-4 and modeling of this process needs verified diffusion data for this specific temperature. Various diffusion couples were assembled from the investigated alloys, annealed at 1288 °C and studied by electron probe microanalysis. So far as the annealing temperature was higher than the γ’-solvus temperature of CMSX-4 and other investigated alloys have no strengthening γ’-phase, interdiffusion occurred in the fcc solid solutions of nickel. It was found that in the case when the γ’-forming and γ-stabilizing elements diffuse in the same direction (towards nickel) the diffusion rate accelerates, but when they diffuse in the opposite directions (counter diffusion) it slows down. Such an interdiffusion behavior is in agreement with the results predicted with diffusion simulation software Dictra.


  • Synchrotron 3D μ-Tomography of Porosity during Hot Isostatic Pressing of a Single-Crystal Nickel-Base Superalloy

    by Alexander Epishin, Bettina Camin, Lennart Hansen, Jonas Schmidt

    The evolution of microporosity in single-crystal nickel-base superalloy CMSX-4 during hot isostatic pressing has been investigated by high resolution tomography at the European Synchrotron Radiation Facility in Grenoble. The kinetic dependencies of microporosity annihilation in the superalloy in initially as-cast and homogenized conditions were obtained. It was shown that smaller homogenization pores of about 5-10 μm in size are rapidly annihilate during hot isostatic pressing, while annihilation of larger solidification pores of size up to a few hundred micrometer takes a long time. After commercial hot isostatic pressing at 1288 °C, 103 MPa, 4 h only rare pores smaller than 20 μm remain, which are not critical for fatigue strength.


  • Open Access

    Synchrotron Sub‐μ X‐ray Tomography of Kirkendall Porosity in a Diffusion Couple of Nickel‐Base Superalloy and Nickel after Annealing at 1250 °C

    by Alexander Epishin, Bettina Camin, Lennart Hansen, Anton Chyrkin, Gert Nolze

    Kirkendall porosity that forms during interdiffusion in a diffusion couple of nickel‐base superalloy CMSX‐10 with pure nickel is investigated. The diffusion experiments are conducted at a temperature of 1250 °C, where the strengthening γ′‐phase is partially dissolved. The porosity is studied by X‐ray sub‐μ tomography with a spatial resolution of about 0.353 μm3 at the European Synchrotron Radiation Facility (ESRF) in Grenoble, France. It is found that depending on the distance from the interface the Kirkendall pores take different shapes: octahedral, rounded pyramidal, drop shaped, dendritic, pear shaped, and joint shapes. Such a variety of pore morphologies indicates a complex multistage process of porosity nucleation and growth under vacancy supersaturation of different degrees. The experimental findings are interpreted on the basis of the results of diffusion modeling. It is shown that the kinetics of porosity growth is essentially influenced by the dissolution of the γ′‐phase.


  • Open Access

    In Situ 3D-µ-Tomography on Particle-Reinforced Light Metal Matrix Composite Materials under Creep Conditions

    by Bettina Camin, Lennart Hansen

    In transportation light metal matrix composites (L-MMCs) are used increasingly due to their improved creep resistance even at higher application temperatures. Therefore, the creep behavior and failure mechanisms of creep loaded particle reinforced L-MMCs have been investigated intensively. Until now, creep damage analyses are usually performed ex situ by means of interrupted creep experiments. However, ex situ methods do not provide sufficient information about the evolution of creep damage. Hence, in situ synchrotron X-ray 3D-µ-tomography investigations were carried out enabling time and space resolved studies of the damage mechanisms in particle-reinforced titanium- and aluminum-based metal matrix composites (MMCs) during creep. The 3D-data were visualized and existing models were applied, specifying the phenomenology of the damage in the early and late creep stages. During the early stages of creep, the damage is determined by surface diffusion in the matrix or reinforcement fracture, both evolving proportionally to the macroscopic creep curve. In the late creep stages the damage mechanisms are quite different: In the Al-MMC, the identified mechanisms persist proportional to creep strain. In contrast, in the titanium-MMC, a changeover to the mechanism of dislocation creep evolving super-proportionally to creep strain occurs.


  • Open Access

    Refinement and Experimental Validation of a Vacancy Model of Pore Annihilation in Single-Crystal Nickel-Base Superalloys During Hot Isostatic Pressing

    by Alexander Epishin, Bettina Camin, Lennart Hansen, Marek Heuser, Inmaculada Lopez-Galilea, Benjamin Ruttert, Werner Theisen, Bernard Fedelich

    Initially as-cast and homogenized single-crystals of nickel-base superalloy CMSX-4 were subjected to hot isostatic pressing at temperature of 1288 °C. Two series of experiments were performed: under the same pressure of 103 MPa but with different durations, between 0.5 and 6 h, and under different pressures, between 15 and 150 MPa, but for the same time of 0.5 h. The porosity annihilation was investigated metallographically and by high resolution synchrotron X-ray tomography. The obtained experimental results were compared with the predictions of the vacancy model proposed recently in our group. In this work the model was further refined by coupling with X-ray tomography. The model describes the evolution of the pore arrays enclosed in the 3D synchrotron tomograms during hot isostatic pressing and properly predicts the time and stress dependences of the pore annihilation kinetics. The validated model and the obtained experimental results can be used for selecting the optimal technological parameters such as applied pressure and processing time.


  • In situ Experiments with Synchrotron High‐Energy X ‐rays and Neutrons

    by Peter Staron, Torben Fischer, Thomas Lippmann, Andreas Stark, Shahrokh Daneshpour, Dirk Schnubel, Eckart Uhlmann, Robert Gerstenberger, Bettina Camin, Walter Reimers, et al.