YLYuan Li

Yuan Li

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Yuan Li has a total of 8 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Smart Interconnected Distribution Substation Network With Integrated Tie Converter: A promising technology

    by Yuan Li, Zhiheng Lin, Yunwei Ryan Li

    The deployment of distributed renewable energy resources (DERs) in North America and numerous other countries has led to a consistent increase in the total capacity of generators connected to the distribution network. The inherent variability and unpredictability of DERs introduce new challenges for distribution system operation and planning, necessitating upgrades to distribution substations.


  • Open Access

    A New Class of Modular Multilevel Converter for Direct AC-AC Conversion

    by Anjana Wijesekera, Yuan Li, Gregory J. Kish

    This article introduces the modular multilevel ac/ac converter (M2AC) which capitalizes on a new partial power processing mechanism (P3M) to achieve direct voltage transformation in single frequency power systems. The proposed P3M allows direct voltage transformation using only half-bridge submodules (HBSM) by harnessing internally circulating dc currents to achieve the charge balance of the submodule capacitors. The M2AC represents a new class of modular multilevel converter (MMC) where, unlike with the classical back-to-back MMC, all submodules contribute to net ac power transfer. When contrasting this single-stage ac/ac conversion process with the ac/dc-dc/ac conversion process for the back-to-back MMC, the M2AC is shown to have a significantly lower semiconductor effort requirement. The article begins by using the classical dc-ac MMC structure to motivate the derivation of the M2AC. A detailed analysis of the M2AC's fundamental working principle is conducted with emphasis on the P3M. A dynamic controller is proposed that incorporates key functionalities such as output voltage regulation and submodule capacitor voltage balancing controls. The M2AC's principle of operation and the proposed controls are validated by simulation studies, and experimental tests performed on a laboratory-scale 250 Vpk, 1.25 kW prototype further confirm the efficacy of the novel P3M. The M2AC offers a new approach to voltage conversion in ac power systems that may be an attractive solution for certain distribution and transmission level applications, primarily where voltage regulation and power flow control are core objectives.


  • Modular Multilevel Converter With Multitasking Magnetics for AC/AC Power Conversion

    by Shehan Herathge, Anjana Wijesekera, Yuan Li, Gregory J. Kish

    This article presents an AC/AC MMC topology with integrated transformer that provides an overall voltage boosting effect beyond that enabled by the transformer turns ratio alone. The proposed three-phase topology also has a simple structure characterized by only six arms and can achieve a low total semiconductor effort. It is thus well suited for applications where higher AC voltage step ratios are needed. These salient features are enabled by a novel power transfer mechanism where the converter-side transformer windings are multitasked to carry current with multiple frequency components, while the core is rated only for a single AC frequency flux similar to conventional power systems transformers. A control strategy based on the $dq$ reference frame is developed that exploits decoupled control of differential mode and common mode currents in the phase arms. The converter's performance is studied under different scenarios using simulations, including fixed frequency and variable frequency operation. A scaled-down 208/104 V, 1 kW three-phase laboratory prototype is employed to further validate the converter operating principle through a series of experiments.


  • Switch Open-Circuit Fault Detection and Localization for Modular Multilevel Converters Based on Signal Synthesis

    by Haoran Wang, Yuan Li, Anjana Wijesekera, Gregory J. Kish, Qing Zhao

    The open-circuit fault detection and localization (FDL) scheme plays a significant role in improving the reliability of modular multilevel converters (MMCs). This article presents a simplified signal synthesis-based FDL scheme with good generality and robustness. The proposed FDL scheme exploits the characteristics that the capacitor voltages of faulty submodules (SMs) have different patterns and higher values than those of healthy ones. Based on this knowledge, certain signature voltage signals are selected, and waveforms consisting of such signatures are reconstructed by the signal synthesis technique to detect and localize the fault. The proposed scheme is suitable for both low voltage and high voltage MMCs since the computational complexity does not change with the number of SMs. The scheme does not rely on system parameters which makes it immune to parameter uncertainties, and there is no need for any additional sensors. Both single and simultaneous multiple faults can be handled with the proposed scheme. Simulation and experimental results validate that the proposed approach based on the signal synthesis method can effectively detect and localize the fault accurately under different loading conditions, and has robustness against load change and circuit parameter uncertainties.


  • A Dual-MMC Chain-Link Structure for Multifrequency Power Transfer

    by Yuan Li, Dalu Liu, Gregory J. Kish

    A dual-modular-multilevel-converter (MMC) structure is presented that allows multifrequency power transfer between its ports. By exploiting a three-winding transformer, where the converter-side windings can multitask by accommodating currents with multiple frequency components, the proposed MMC structure can be deployed for two different applications: 1) a dc–ac MMC with independent control of currents in the two dc poles to accommodate unbalanced conditions in bipolar dc systems, and 2) a three-port MMC that can achieve simultaneous dc–dc and dc–ac conversions between an ac grid and two dc systems. DC flux cancellation is imposed in the transformer core by using a center-tapped connection of the converter-side windings. A unified control scheme is developed that independently controls dc and ac terminal power transfers while keeping submodule capacitor voltages balanced. Converter operation and dynamic controls are validated by simulation and experiment.


  • Open Access

    Comparative Assessment of Multi-Port MMCs for High-Power Applications

    by Yuan Li, Gregory J. Kish

    Multi-port converters can interconnect different dc and ac systems while reducing semiconductor requirements and losses by eliminating redundant power conversion stages. Modular multilevel converter (MMC)-based multiport systems are well suited for application in mixed ac-dc grids containing high-voltage dc (HVDC) and medium-voltage dc (MVDC) systems. This paper conducts a detailed comparative assessment of multi-port dc-dc-ac MMCs for high power applications. Four representative topologies are chosen for study due to their contrasting internal power processing characteristics. Three different network scenarios are investigated that include HVDC and MVDC applications, covering several different power flow cases. The multi-port MMCs are compared in terms of losses, semiconductor effort, internal energy storage and magnetics requirements. The results are extensively discussed and general conclusions are summarized.


  • Open Access

    The Modular Multilevel DC Converter With Inherent Minimization of Arm Current Stresses

    by Yuan Li, Gregory J. Kish

    The modular multilevel dc converter (M2DC) is a partial power processing dc-dc converter that is gaining popularity for medium-voltage and high-voltage dc grid applications. However, internal ac current stresses go up as the step-down dc voltage ratio increases, leading to increased cost and losses, and ultimately renders the M2DC impractical for some applications. The HVDC autotransformer (AT) is another class of partial power processing dc-dc converter that circumvents this issue by using a transformer for inter-arm ac voltage matching, although the core must tolerate a very large dc voltage stress between windings that leads to increased magnetics size and weight. Interestingly, the M2DC does not suffer from inter-winding dc voltage stresses. This paper presents a new class of partial power processing dc-dc converter that uses an integrated center-tapped transformer to merge the best traits of the M2DC and HVDC-AT. Comparative analysis reveals the proposed converter can minimize ac current stresses at all operating points while also achieving a significant reduction in transformer area product relative to the HVDC-AT. A dynamic controller is proposed that regulates dc power transfer while ensuring balanced capacitor voltages. The converter operation and dynamic controls are validated by simulation and experiment.