Wenjia Su
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Wenjia Su has a total of 28 co-authors. Here are the top co-authors by number of shared publications:
Jiulong Li
The Institute of Technological Sciences, Wuhan University, Wuhan, China
11 shared publicationsJiaqi Li
School of Energy and Power Engineering, Jiangsu University, Zhenjiang, China
6 shared publicationsWei Yang
6 shared publicationsZhen Zhang
School of Energy and Power Engineering, Jiangsu University, Zhenjiang, China
6 shared publicationsZhicheng Guan
School of Energy and Power Engineering, Jiangsu University, Zhenjiang, China
6 shared publicationsJunfeng Wang
4 shared publications
Latest Publications
- 3 October 2026
- Published by Elsevier in Journal of Crystal Growth
- Vol. 697
Numerical optimization of induction coils structure for TSSG-SiC crystal growth
- 3 October 2026
- Published by Elsevier in Journal of Crystal Growth
- Vol. 697
Numerical optimization of induction coils structure for TSSG-SiC crystal growth
- 28 February 2025
- Published by Springer Nature in Silicon
- Vol. 17 (5) , 1153-1163
Numerical Study on Different Shapes of Heat Shields in Continuous Czochralski Silicon
- 28 February 2025
- Published by Springer Nature in Silicon
- Vol. 17 (5) , 1153-1163
Numerical Study on Different Shapes of Heat Shields in Continuous Czochralski Silicon
- 1 April 2023
- Published by Springer Nature in Silicon
- Vol. 15 (12) , 5307-5315
Numerical Study on the Effect of Water-cooling Jacket Radius on Czochralski Silicon
- 1 April 2023
- Published by Springer Nature in Silicon
- Vol. 15 (12) , 5307-5315
Numerical Study on the Effect of Water-cooling Jacket Radius on Czochralski Silicon
- 15 February 2023
- Published by Springer Nature in Silicon
- Vol. 15 (9) , 4127-4135
Numerical Analysis of the Influence of Size Upgrading on Oxygen and Carbon Impurities in Casting Silicon
- 15 February 2023
- Published by Springer Nature in Silicon
- Vol. 15 (9) , 4127-4135
Numerical Analysis of the Influence of Size Upgrading on Oxygen and Carbon Impurities in Casting Silicon
- 30 November 2022
- Published by Springer Nature in Silicon
- Vol. 15 (7) , 3103-3112
Numerical Investigation on the Effect of Thermal Gate Moving Rate on Directional Solidification Process
- 30 November 2022
- Published by Springer Nature in Silicon
- Vol. 15 (7) , 3103-3112
Numerical Investigation on the Effect of Thermal Gate Moving Rate on Directional Solidification Process
- Open Access
- 13 October 2022
- Published by Springer Nature in Research Square
Numerical Analysis of the Influence of Size Upgrading on Oxygen and Carbon Impurities in Casting Silicon
Size upgrading is the main method to increase production capacity and reduce production costs during the directional solidification of silicon ingots. The performance of solar cells depends directly on the quality of the wafer and impurities distributions in silicon ingots. The distributions of oxygen and carbon impurities in G6 and G7 directional solidification furnaces are studied. The transient global simulation method is used to calculate the coupled thermal and flow fields in the furnaces, considering the convection of gas and melt, chemical reactions, and segregations of the impurities at the crystal-melt interface. The simulation results show that the distributions of oxygen and carbon impurities change significantly in the silicon ingot at different growth stages, especially the position of the highest concentration of carbon impurities has shifted. Compared with the G6 furnace, the average concentrations of oxygen and carbon in silicon crystal in the G7 furnace are reduced by 6.7%, and 7.3% respectively. With the growth of silicon crystal, the average concentration of oxygen gradually decreases, while the average concentration of carbon gradually increases.
- 13 October 2022
- Published by Springer Nature in Research Square
Open AccessNumerical Analysis of the Influence of Size Upgrading on Oxygen and Carbon Impurities in Casting Silicon
Size upgrading is the main method to increase production capacity and reduce production costs during the directional solidification of silicon ingots. The performance of solar cells depends directly on the quality of the wafer and impurities distributions in silicon ingots. The distributions of oxygen and carbon impurities in G6 and G7 directional solidification furnaces are studied. The transient global simulation method is used to calculate the coupled thermal and flow fields in the furnaces, considering the convection of gas and melt, chemical reactions, and segregations of the impurities at the crystal-melt interface. The simulation results show that the distributions of oxygen and carbon impurities change significantly in the silicon ingot at different growth stages, especially the position of the highest concentration of carbon impurities has shifted. Compared with the G6 furnace, the average concentrations of oxygen and carbon in silicon crystal in the G7 furnace are reduced by 6.7%, and 7.3% respectively. With the growth of silicon crystal, the average concentration of oxygen gradually decreases, while the average concentration of carbon gradually increases.
- Open Access
- 4 October 2022
- Published by Springer Nature in Research Square
Numerical investigation on the effect of thermal gate moving rate on directional solidification process
The temperature field distribution during the growth of crystalline silicon by the directional solidification (DS) method is an important factor affecting the growth rate, the shape of the melt-crystal (m-c) interface, and thermal stress. To solve the problem of m-c interface convexity at the early stage of crystal growth caused by supercooling at the bottom center of silicon ingot during DS. In this paper, a two-dimensional global transient numerical model based on a large-size ALD-G7 (G7) crystalline silicon ingot furnace is established and experimentally verified. Based on the model, the influence of different bottom thermal gate moving process curves on the convexity of the m-c interface at the early stage was studied, with emphasis on the changes in temperature field, m-c interface, and thermal stress at the early stage of crystal growth. We have designed three cases, case 1 uses the original moving process curve of bottom thermal gate, case 2 and case 3 adjust the process curve to 0.95 and 0.9 of the original ratio, respectively. The numerical results show that the center cooling condition of silicon ingot and the convexity of the m-c interface are improved with the decreasing of thermal gate moving rate. Compared with case 1, the convexity of case 2 and case 3 is reduced by 55% and 44% on average, respectively.
- 4 October 2022
- Published by Springer Nature in Research Square
Open AccessNumerical investigation on the effect of thermal gate moving rate on directional solidification process
The temperature field distribution during the growth of crystalline silicon by the directional solidification (DS) method is an important factor affecting the growth rate, the shape of the melt-crystal (m-c) interface, and thermal stress. To solve the problem of m-c interface convexity at the early stage of crystal growth caused by supercooling at the bottom center of silicon ingot during DS. In this paper, a two-dimensional global transient numerical model based on a large-size ALD-G7 (G7) crystalline silicon ingot furnace is established and experimentally verified. Based on the model, the influence of different bottom thermal gate moving process curves on the convexity of the m-c interface at the early stage was studied, with emphasis on the changes in temperature field, m-c interface, and thermal stress at the early stage of crystal growth. We have designed three cases, case 1 uses the original moving process curve of bottom thermal gate, case 2 and case 3 adjust the process curve to 0.95 and 0.9 of the original ratio, respectively. The numerical results show that the center cooling condition of silicon ingot and the convexity of the m-c interface are improved with the decreasing of thermal gate moving rate. Compared with case 1, the convexity of case 2 and case 3 is reduced by 55% and 44% on average, respectively.
- Open Access
Design and Numerical Study of Argon Gas Diversion System Using Orthogonal Experiment to Reduce Impurities in Large-Sized Casting Silicon
To reduce oxygen and carbon impurities while casting silicon, an argon gas diversion system is proposed. A series of two-dimensional global transient numerical simulations are carried out using Fluent software according to the orthogonal experimental design, including heat transfer, convection of silicon melt and argon gas, and the fully coupling transport of impurities. The numerical results show that when the distance between the outer tube outlet and the cover is 10 mm, the backflow is inhibited by lateral outflow, thus the generation of CO is suppressed and the penetration of impurities into the silicon melt is decreased. The larger the flow rate, the more obvious the effect is. When the outer tube outlet is far from the cover, the effect of removing impurities is no longer significant. In addition, too large or too small an inner tube flow rate is not conducive to impurity reduction. The optimal parameter combination of outer tube flow rate, inner tube flow rate, and the distance between outer tube outlet and the cover are determined by the orthogonal experiment. Compared with the original furnace, the average concentration of oxygen and carbon in casting silicon ingots could be decreased by 7.4% and 59.9%, respectively, by using the optimized argon gas diversion system.
Open AccessDesign and Numerical Study of Argon Gas Diversion System Using Orthogonal Experiment to Reduce Impurities in Large-Sized Casting Silicon
To reduce oxygen and carbon impurities while casting silicon, an argon gas diversion system is proposed. A series of two-dimensional global transient numerical simulations are carried out using Fluent software according to the orthogonal experimental design, including heat transfer, convection of silicon melt and argon gas, and the fully coupling transport of impurities. The numerical results show that when the distance between the outer tube outlet and the cover is 10 mm, the backflow is inhibited by lateral outflow, thus the generation of CO is suppressed and the penetration of impurities into the silicon melt is decreased. The larger the flow rate, the more obvious the effect is. When the outer tube outlet is far from the cover, the effect of removing impurities is no longer significant. In addition, too large or too small an inner tube flow rate is not conducive to impurity reduction. The optimal parameter combination of outer tube flow rate, inner tube flow rate, and the distance between outer tube outlet and the cover are determined by the orthogonal experiment. Compared with the original furnace, the average concentration of oxygen and carbon in casting silicon ingots could be decreased by 7.4% and 59.9%, respectively, by using the optimized argon gas diversion system.
- 1 September 2021
- Published by Elsevier in Solar Energy Materials and Solar Cells
- Vol. 230
Impact of seed orientation on dislocation propagation in cast seed-assisted monocrystalline silicon
- 1 September 2021
- Published by Elsevier in Solar Energy Materials and Solar Cells
- Vol. 230
Impact of seed orientation on dislocation propagation in cast seed-assisted monocrystalline silicon
- 7 June 2021
- Published by Springer Nature in Silicon
- Vol. 14 (1) , 301-307
Design and Numerical Optimization of Gas Guidance System in Casting Silicon Furnace by the Orthogonal Experiment
- 7 June 2021
- Published by Springer Nature in Silicon
- Vol. 14 (1) , 301-307
Design and Numerical Optimization of Gas Guidance System in Casting Silicon Furnace by the Orthogonal Experiment