YSYafei Shi

Yafei Shi

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Yafei Shi has a total of 15 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • DC-Link Capacitance Estimation for Power Converters Using Integrated PCB Rogowski Coils

    by Yafei Shi, Zhen Xin, Jianlong Kang, Jianliang Chen, Yongjian Li, Huai Wang

    Capacitance is a key electrical parameter of capacitors in power electronic converters and its estimation is important for the stable operation of the converters. This paper presents a small printed circuit board (PCB) with Rogowski coils for measuring ripple voltage rate (dv/dt) and ripple current in an online and contactless manner to estimate the capacitance. Electric field coupling is utilized to achieve dv/dt measurement capability in the Rogowski coil-based current sensing solutions. The coils and processing circuit are designed to achieve high sensitivity and low noise for accurate low-frequency band measurements. The wireless module is integrated to sample and transmit the result without any wiring. Through a case study of an aluminum electrolytic capacitor, the proposed method has been demonstrated to be applicable to capacitors in converters. The small PCB is nested on the capacitor terminals, and the accuracy of the presented method is verified through offline, online-based single-phase inverter, and degradation emulation experiments.


  • A Closed-Loop Compensated Rogowski Coil Current Sensor for Three-Phase Inverter

    by Zhen Xin, Yu Yao, Jianlong Kang, Qian Li, Ze Zhou, Yafei Shi

    Accurate current measurement is crucial in power electronic converters to achieve fault protection and current control. Among the various options available, the printed circuit board Rogowski coil current sensor (PCB RCCS) emerges as a strong contender due to its advantages of higher bandwidth, smaller volume, and lower cost. However, the presence of offset voltage and offset current in operational amplifiers (op-amps) greatly limits the measurement accuracy of PCB RCCS, and is greatly affected by the individual differences of op-amps and temperature changes. Traditional error compensation methods lack self-adjusting capabilities, leading to significant limitations in compensation effectiveness. This article proposes a closed-loop error compensation method that can monitor the compensation effect in real-time under actual operating conditions, adjust the compensating signal promptly, and achieve precise compensation of integral errors in PCB RCCS. Moreover, the proposed PCB RCCS is highly integrated into a three-phase inverter, achieving not only reliable short-circuit protection for power devices but also recovering phase current information for successful utilization in system current control.


  • An IGBT Junction Temperature Estimation Method Based on Turn-Off Maximum di C/dt With Decoupling Load Current

    by Yafei Shi, Boyang Zhang, Jianlong Kang, Yaokang Lai, Huai Wang, Zhen Xin

    Monitoring the junction temperature Tj of insulated gate bipolar transistor modules is crucial for reliable operation in medium/high voltage applications. Among the various temperature-sensitive electrical parameters, the maximum collector current falling rate d i C /d t max is an effective indicator characterized by excellent linearity and amenability to real-time detection. However, current acquisition methods are prone to introduce parasitic parameters, and d i C /d t max is also affected by the load current i load . In response to these challenges, the printed circuit board Rogowski coil is proposed to measure d i C /d t max and i load , which can decouple the effect of i load , and this method has the advantage of being contactless and integratable. In this article, the dependence of d i C /d t max on Tj and i load is theoretically analyzed. The system design of the Rogowski coil current sensor, including coil structure, integrator, and peak detection circuit is carried out. The effective bandwidth and measurement accuracy of the sensor are verified based on the vector network analyzer and the double pulse test, and the effectiveness of the method for Tj estimation is verified based on the buck converter.


  • Design and Modeling of the PCB Rogowski Coil with Multiple Vias for Power Devices

    by Yafei Shi, Zhen Xin, Ze Zhou, Yu Yao

    The Printed circuit board (PCB) Rogowski coil, with high bandwidth, small size, and low cost, has already been used for current measurement in power devices. Accurate parameter calculations are crucial for predicting performance and designing the coils. The traditional methods use simple empirical formulas and neglect the parasitic effects of PCB vias, resulting in low model accuracy. In this paper, the parasitic parameters and transfer characteristics of PCB Rogowski coil windings are obtained by modeling the PCB traces and vias. Based on the model, the influence of winding dimensions on the parasitic parameters and the performance of coil are discussed. The accuracy of the method is verified by comparing the results with the vector network analyzer and impedance analyzer measurements.


  • Design of PCB Rogowski Current Sensor with Digital Compensation for Three-Phase Inverter

    by Yu Yao, Ze Zhou, Yafei Shi, Zhen Xin

    Reliable current closed loop and rapid current short-circuit protection are essential for the stable and safe operation of the three-phase inverter. It can be achieved by the Hall current sensor and desaturation detection circuit before. However, with continuous improvement of silicon carbide metal-oxide-semiconductor field-effect transistors (SiC MOSFETs) device technology, power electronic devices posed higher challenges to current sensing technology. Attention has been drawn to the Rogowski current sensor (RSCS) in recent years because of its advantages in terms of bandwidth, volume, and cost. However, the result of PCB RSCS is mixed with droop, drift and offset errors which can damage the normal operation of power devices. This paper proposes a digital bias and drift compensation method aimed at offset voltage of op-amps and charge injection of analog switches. The effectiveness of the proposed method is proved in a 10 kW three-phase inverter.

  • A Noncontact Method for Simultaneous Measurement of di/dt and dv/dt

    by Yafei Shi, Weijian Han, Xuebao Li, Zhen Xin, Huai Wang

    In this letter, we propose a noncontact method for simultaneously measuring the current and voltage change rates by Rogowski coils. The dv/dt measurement capability is achieved based on electric field coupling, which is incorporated into the state-of-the-art Rogowski coil-based current sensing solutions. The application of the proposed method for power semiconductor devices is demonstrated by a case study of an insulated gate bipolar transistor (IGBT) switching circuit. The Rogowski coils are integrated with a printed circuit board (PCB) and fit with the IGBT module terminals. The comparable results from high-performance commercial instruments verify the di/dt and dv/dt measurement accuracy of the presented compact and cost-effective solution.


  • Top Cited Papers
    Open Access

    A Review of Traditional Helical to Recent Miniaturized Printed Circuit Board Rogowski Coils for Power-Electronic Applications

    by Yafei Shi, Zhen Xin, Poh Chiang Loh, Frede Blaabjerg

    Latest wide-bandgap power devices are switching progressively faster compared with existing silicon devices. Their accurate current measurements for either control or protection have therefore become tougher. One method that can fulfill the requirements is to use a Rogowski coil and its accompanied electronics to form a Rogowski current sensor with high bandwidth, small volume, low cost, and ease of integration. This article therefore aims to review various aspects of the Rogowski current sensor from its history, measuring principles to modern power-electronic applications. The applications have, in turn, motivated a progression from traditional helical to recent miniaturized printed circuit board implementation, in order to improve the overall power density. This progression has similarly been reviewed, together with its various design aspects applied to the winding, integrator, shielding, and parameters of the Rogowski current sensor. Future challenges and directions are then summarized, whose ultimate goal is to maximize accuracy over a wide bandwidth without being affected by radiated and near-field-coupling interferences.