Ze Zhou
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Ze Zhou has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Zhen Xin
State Key Laboratory of Intelligent Power Distribution Equipment and System, Hebei University of Technology, Tianjin, China
5 shared publications - Haoze Luo
Zhejiang University
3 shared publications - Jianlong Kang
State Key Laboratory of Intelligent Power Distribution Equipment and System, Hebei University of Technology, Tianjin, China
3 shared publications - Yafei Shi
State Key Laboratory of EERI, Hebei University of Technology, Tianjin, China
3 shared publications - Yaping Xu
School of Mathematics Hunan University 410082 Changsha China
2 shared publications - Yu Yao
School of Automation Science and Electrical Engineering, Beihang University, Beijing, China
2 shared publications
Latest Publications
- 11 March 2026
- Published by World Scientific Pub Co Pte Ltd in Communications in Contemporary Mathematics
Combinatorial Yamabe flow on hyperbolic bordered surfaces
This paper studies the combinatorial Yamabe flow on hyperbolic bordered surfaces. We show that the flow exists for all time and converges exponentially fast to a conformal factor which produces a hyperbolic surface whose lengths of boundary components are equal to the prescribed positive numbers. This provides an algorithm to such problems.
- 11 March 2026
- Published by World Scientific Pub Co Pte Ltd in Communications in Contemporary Mathematics
Combinatorial Yamabe flow on hyperbolic bordered surfaces
This paper studies the combinatorial Yamabe flow on hyperbolic bordered surfaces. We show that the flow exists for all time and converges exponentially fast to a conformal factor which produces a hyperbolic surface whose lengths of boundary components are equal to the prescribed positive numbers. This provides an algorithm to such problems.
- Open Access
A gradient descent algorithm for computing circle patterns
This paper presents a new algorithm for generating planar circle patterns. The algorithm employs gradient descent and conjugate gradient method to compute circle radii and centers separately. Compared with existing algorithms, the proposed method is more efficient in computing centers of circles and is applicable for realizing circle patterns with possible obtuse overlap angles.
Open AccessA gradient descent algorithm for computing circle patterns
This paper presents a new algorithm for generating planar circle patterns. The algorithm employs gradient descent and conjugate gradient method to compute circle radii and centers separately. Compared with existing algorithms, the proposed method is more efficient in computing centers of circles and is applicable for realizing circle patterns with possible obtuse overlap angles.
- 29 September 2025
- Published by Springer Nature in Mathematische Annalen
- Vol. 393 (3-4) , 2899-2923
Generalizing Andreev’s Theorem via circle patterns
- 29 September 2025
- Published by Springer Nature in Mathematische Annalen
- Vol. 393 (3-4) , 2899-2923
Generalizing Andreev’s Theorem via circle patterns
- 18 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 13 (2) , 2113-2124
An Integrable High-Frequency 3-D Magnetic Field Scanning Method for Power Module
As one of the key parameters of power modules, the high-frequency magnetic field not only reflects their switching characteristics and spatial distribution, but also plays a crucial role in electromagnetic compatibility evaluation, reliability design, and chip selection. However, due to the presence of multiple field sources and strong coupling within the device, existing magnetic field scanning techniques face challenges in meeting the demands for high bandwidth, compact size, and cost-effectiveness. This paper introduces an integrable three-dimensional (3D) magnetic field scanning method based on air-coil. By capturing magnetic field distribution (MFD) along the (x, y, z) axes, the 3D magnetic field map inside the power device can be reconstructed. An integrable 3D magnetic field probe (MFP) was designed, taking into account packaging characteristics and current distribution, enabling real-time monitoring. Finally, a multi-pulse generation platform was developed to validate the feasibility of the proposed method. The experimental prototype achieved a bandwidth limit of up to 30 MHz and a sensitivity of approximately 10 V/T (or 0.01V/(A/m) in 0.2mm).
- 18 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 13 (2) , 2113-2124
An Integrable High-Frequency 3-D Magnetic Field Scanning Method for Power Module
As one of the key parameters of power modules, the high-frequency magnetic field not only reflects their switching characteristics and spatial distribution, but also plays a crucial role in electromagnetic compatibility evaluation, reliability design, and chip selection. However, due to the presence of multiple field sources and strong coupling within the device, existing magnetic field scanning techniques face challenges in meeting the demands for high bandwidth, compact size, and cost-effectiveness. This paper introduces an integrable three-dimensional (3D) magnetic field scanning method based on air-coil. By capturing magnetic field distribution (MFD) along the (x, y, z) axes, the 3D magnetic field map inside the power device can be reconstructed. An integrable 3D magnetic field probe (MFP) was designed, taking into account packaging characteristics and current distribution, enabling real-time monitoring. Finally, a multi-pulse generation platform was developed to validate the feasibility of the proposed method. The experimental prototype achieved a bandwidth limit of up to 30 MHz and a sensitivity of approximately 10 V/T (or 0.01V/(A/m) in 0.2mm).
- 9 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 13 (1) , 380-393
Case Temperature Waveform Similarity-Based Online Aging Monitoring for SiC MOSFETs of Accelerated Power Cycling Tests for DC-SSPCs
Online condition monitoring of SiC MOSFETs is essential for improving the reliability of Solid-State Power Controllers (DC-SSPC). Traditional monitoring methods based on electrical parameters require the design of highly precise monitoring circuits and complex control systems, to prevent disruptions to the system’s normal operation. This paper introduces a non-electrical, easily measured parameter—the case temperature—as a means of monitoring the aging status of SiC MOSFETs online, using an electrically insulated temperature sensor. Two aging characteristic parameters, mea cosk and std cosk, are proposed based on the improved cosine similarity of the case temperature waveform. These parameters enable effective tracking of overall aging trends of SiC MOSFETs and allow for the detection of severe aging in the bonding wire and the solder layer, without dependence on electrical parameters. This approach enhances the practicality of non-invasive and online monitoring. The effectiveness of the proposed method is validated through experiment results. Ultimately, this conditions monitoring technique supports fault diagnosis and predictive maintenance for DC-SSPCs.
- 9 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. 13 (1) , 380-393
Case Temperature Waveform Similarity-Based Online Aging Monitoring for SiC MOSFETs of Accelerated Power Cycling Tests for DC-SSPCs
Online condition monitoring of SiC MOSFETs is essential for improving the reliability of Solid-State Power Controllers (DC-SSPC). Traditional monitoring methods based on electrical parameters require the design of highly precise monitoring circuits and complex control systems, to prevent disruptions to the system’s normal operation. This paper introduces a non-electrical, easily measured parameter—the case temperature—as a means of monitoring the aging status of SiC MOSFETs online, using an electrically insulated temperature sensor. Two aging characteristic parameters, mea cosk and std cosk, are proposed based on the improved cosine similarity of the case temperature waveform. These parameters enable effective tracking of overall aging trends of SiC MOSFETs and allow for the detection of severe aging in the bonding wire and the solder layer, without dependence on electrical parameters. This approach enhances the practicality of non-invasive and online monitoring. The effectiveness of the proposed method is validated through experiment results. Ultimately, this conditions monitoring technique supports fault diagnosis and predictive maintenance for DC-SSPCs.
- 19 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (1) , 2126-2138
A Closed-Loop Compensated Rogowski Coil Current Sensor for Three-Phase Inverter
Accurate current measurement is crucial in power electronic converters to achieve fault protection and current control. Among the various options available, the printed circuit board Rogowski coil current sensor (PCB RCCS) emerges as a strong contender due to its advantages of higher bandwidth, smaller volume, and lower cost. However, the presence of offset voltage and offset current in operational amplifiers (op-amps) greatly limits the measurement accuracy of PCB RCCS, and is greatly affected by the individual differences of op-amps and temperature changes. Traditional error compensation methods lack self-adjusting capabilities, leading to significant limitations in compensation effectiveness. This article proposes a closed-loop error compensation method that can monitor the compensation effect in real-time under actual operating conditions, adjust the compensating signal promptly, and achieve precise compensation of integral errors in PCB RCCS. Moreover, the proposed PCB RCCS is highly integrated into a three-phase inverter, achieving not only reliable short-circuit protection for power devices but also recovering phase current information for successful utilization in system current control.
- 19 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 40 (1) , 2126-2138
A Closed-Loop Compensated Rogowski Coil Current Sensor for Three-Phase Inverter
Accurate current measurement is crucial in power electronic converters to achieve fault protection and current control. Among the various options available, the printed circuit board Rogowski coil current sensor (PCB RCCS) emerges as a strong contender due to its advantages of higher bandwidth, smaller volume, and lower cost. However, the presence of offset voltage and offset current in operational amplifiers (op-amps) greatly limits the measurement accuracy of PCB RCCS, and is greatly affected by the individual differences of op-amps and temperature changes. Traditional error compensation methods lack self-adjusting capabilities, leading to significant limitations in compensation effectiveness. This article proposes a closed-loop error compensation method that can monitor the compensation effect in real-time under actual operating conditions, adjust the compensating signal promptly, and achieve precise compensation of integral errors in PCB RCCS. Moreover, the proposed PCB RCCS is highly integrated into a three-phase inverter, achieving not only reliable short-circuit protection for power devices but also recovering phase current information for successful utilization in system current control.
- 28 June 2024
- Published by Elsevier in Topology and its Applications
- Vol. 355
Estimates on the topological Hausdorff dimensions of fractal squares
- 28 June 2024
- Published by Elsevier in Topology and its Applications
- Vol. 355
Estimates on the topological Hausdorff dimensions of fractal squares
- 29 May 2024
- Published by Elsevier in Topology and its Applications
- Vol. 354
Polygons inscribed in Jordan curves with prescribed edge ratios
- 29 May 2024
- Published by Elsevier in Topology and its Applications
- Vol. 354
Polygons inscribed in Jordan curves with prescribed edge ratios
- 10 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1072-1076
Design and Modeling of the PCB Rogowski Coil with Multiple Vias for Power Devices
The Printed circuit board (PCB) Rogowski coil, with high bandwidth, small size, and low cost, has already been used for current measurement in power devices. Accurate parameter calculations are crucial for predicting performance and designing the coils. The traditional methods use simple empirical formulas and neglect the parasitic effects of PCB vias, resulting in low model accuracy. In this paper, the parasitic parameters and transfer characteristics of PCB Rogowski coil windings are obtained by modeling the PCB traces and vias. Based on the model, the influence of winding dimensions on the parasitic parameters and the performance of coil are discussed. The accuracy of the method is verified by comparing the results with the vector network analyzer and impedance analyzer measurements.
- 10 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1072-1076
Design and Modeling of the PCB Rogowski Coil with Multiple Vias for Power Devices
The Printed circuit board (PCB) Rogowski coil, with high bandwidth, small size, and low cost, has already been used for current measurement in power devices. Accurate parameter calculations are crucial for predicting performance and designing the coils. The traditional methods use simple empirical formulas and neglect the parasitic effects of PCB vias, resulting in low model accuracy. In this paper, the parasitic parameters and transfer characteristics of PCB Rogowski coil windings are obtained by modeling the PCB traces and vias. Based on the model, the influence of winding dimensions on the parasitic parameters and the performance of coil are discussed. The accuracy of the method is verified by comparing the results with the vector network analyzer and impedance analyzer measurements.
- 10 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1077-1081
Design of PCB Rogowski Current Sensor with Digital Compensation for Three-Phase Inverter
Reliable current closed loop and rapid current short-circuit protection are essential for the stable and safe operation of the three-phase inverter. It can be achieved by the Hall current sensor and desaturation detection circuit before. However, with continuous improvement of silicon carbide metal-oxide-semiconductor field-effect transistors (SiC MOSFETs) device technology, power electronic devices posed higher challenges to current sensing technology. Attention has been drawn to the Rogowski current sensor (RSCS) in recent years because of its advantages in terms of bandwidth, volume, and cost. However, the result of PCB RSCS is mixed with droop, drift and offset errors which can damage the normal operation of power devices. This paper proposes a digital bias and drift compensation method aimed at offset voltage of op-amps and charge injection of analog switches. The effectiveness of the proposed method is proved in a 10 kW three-phase inverter.
- 10 November 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1077-1081
Design of PCB Rogowski Current Sensor with Digital Compensation for Three-Phase Inverter
Reliable current closed loop and rapid current short-circuit protection are essential for the stable and safe operation of the three-phase inverter. It can be achieved by the Hall current sensor and desaturation detection circuit before. However, with continuous improvement of silicon carbide metal-oxide-semiconductor field-effect transistors (SiC MOSFETs) device technology, power electronic devices posed higher challenges to current sensing technology. Attention has been drawn to the Rogowski current sensor (RSCS) in recent years because of its advantages in terms of bandwidth, volume, and cost. However, the result of PCB RSCS is mixed with droop, drift and offset errors which can damage the normal operation of power devices. This paper proposes a digital bias and drift compensation method aimed at offset voltage of op-amps and charge injection of analog switches. The effectiveness of the proposed method is proved in a 10 kW three-phase inverter.