Zeno Michael
Research Subjects
Zeno Michael has a total of 44 co-authors. Here are the top co-authors by number of shared publications:
M. Khairulmaini
Faculty of Mechanical Engineering, UiTM Cawangan Johor, Kampus Pasir Gudang, Jalan Purnama, 81750 Masai, Johor
3 shared publications- Aman Mohd Ihsan Mamat
Universiti Teknologi MARA
2 shared publications - Irnie Azlin Zakaria
Faculty of Mechanical Engineering, Universiti Teknologi MARA (UITM), Shah Alam, Malaysia
2 shared publications Nik Rosli Abdullah
Faculty of Mechanical Engineering, UiTM ,40450 Shah Alam, Selangor, Malaysia
2 shared publicationsR. Saidur
2 shared publicationsWan Ahmad Najmi Wan Mohamed
Faculty of Mechanical Engineering, Universiti Teknologi Mara ( UiTM ), Shah Alam, Malaysia
2 shared publications
Latest Publications
- Open Access
- 24 February 2022
- Published by Warsaw University of Life Sciences - SGGW Press in Scientific Review Engineering and Environmental Sciences (SREES)
- Vol. 31 (1) , 3-13
Feasibility study of palm oil boiler ash (POBA) as a partial replacement of sand in foamed concrete
A study was conducted to explore the effect of palm oil boiler ash (POBA) on foamed concrete by varying the percentage of POBA over sand quantities (0, 4, 8 and 12%). This paper primarily discusses the water absorption test, uniaxial compressive strength, and dry density findings. It indicates that substituting sand with POBA greatly enhances the strength of foamed concrete. When the quantity of POBA was raised up to 12% throughout all curing times, the compressive strength steadily increased in the range of 4.34–13.50 N·mm–2. Furthermore, the dry density of foamed concrete was shown to be directly related to the fraction of POBA in the mixture. The dry density of foamed concrete increases as the amount of POBA increases. Despite this, water absorption shown that increasing POBA increases water absorption percentage in foamed concrete from 7.4 to 10.4%. This is due to the fact that a composition with a high POBA percentage will generate more pores than a mixture with a low POBA percentage.
- 24 February 2022
- Published by Warsaw University of Life Sciences - SGGW Press in Scientific Review Engineering and Environmental Sciences (SREES)
- Vol. 31 (1) , 3-13
Open AccessFeasibility study of palm oil boiler ash (POBA) as a partial replacement of sand in foamed concrete
A study was conducted to explore the effect of palm oil boiler ash (POBA) on foamed concrete by varying the percentage of POBA over sand quantities (0, 4, 8 and 12%). This paper primarily discusses the water absorption test, uniaxial compressive strength, and dry density findings. It indicates that substituting sand with POBA greatly enhances the strength of foamed concrete. When the quantity of POBA was raised up to 12% throughout all curing times, the compressive strength steadily increased in the range of 4.34–13.50 N·mm–2. Furthermore, the dry density of foamed concrete was shown to be directly related to the fraction of POBA in the mixture. The dry density of foamed concrete increases as the amount of POBA increases. Despite this, water absorption shown that increasing POBA increases water absorption percentage in foamed concrete from 7.4 to 10.4%. This is due to the fact that a composition with a high POBA percentage will generate more pores than a mixture with a low POBA percentage.
- 1 January 2021
- Published by Elsevier in Materials Today: Proceedings
- Vol. 46, 1618-1625
Deformation and failure behavior of hybrid composite laminates made of Glass Epoxy and woven Kevlar Epoxy
- 1 January 2021
- Published by Elsevier in Materials Today: Proceedings
- Vol. 46, 1618-1625
Deformation and failure behavior of hybrid composite laminates made of Glass Epoxy and woven Kevlar Epoxy
- Open Access
- 1 April 2020
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 834 (1) , 012019
Improvement of Insulation Material for Cool Box Application
Current conventional cool boxes which use expanded polystyrene (EPS) as its insulating material cannot seem to maintain storage at low temperature for long periods. This study aims to determine the effect for different types of insulating materials which can be used in cool boxes to improve its thermal insulation. Using theoretical and simulation approach, three out of six potential insulating materials were chosen in terms of their heat transfer rate, and temperature at the outer wall. The three best insulating materials, polyurethane (PU), expanded polystyrene (EPS) and poly-glass fibre (PGF) were then tested at three different room temperatures experimentally using the thermal insulation test to determine the best insulating material for a cool box. Tensile and density were also conducted to identify the mechanical behaviour and properties of these insulating materials. From the results obtained from the experiment, polyurethane (PU) recorded the longest time taken for ice to change into water at the three different temperatures when compared to other insulating materials. The results showed that when thermal conductivity is low, the heat transferred through the walls of the cool box was also low thus resulting in better thermal insulation of the cool box. This study gives a better understanding in term of thermal insulation and the results obtained from this study can help with the production of better cool boxes with improved thermal insulation.
- 1 April 2020
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 834 (1) , 012019
Open AccessImprovement of Insulation Material for Cool Box Application
Current conventional cool boxes which use expanded polystyrene (EPS) as its insulating material cannot seem to maintain storage at low temperature for long periods. This study aims to determine the effect for different types of insulating materials which can be used in cool boxes to improve its thermal insulation. Using theoretical and simulation approach, three out of six potential insulating materials were chosen in terms of their heat transfer rate, and temperature at the outer wall. The three best insulating materials, polyurethane (PU), expanded polystyrene (EPS) and poly-glass fibre (PGF) were then tested at three different room temperatures experimentally using the thermal insulation test to determine the best insulating material for a cool box. Tensile and density were also conducted to identify the mechanical behaviour and properties of these insulating materials. From the results obtained from the experiment, polyurethane (PU) recorded the longest time taken for ice to change into water at the three different temperatures when compared to other insulating materials. The results showed that when thermal conductivity is low, the heat transferred through the walls of the cool box was also low thus resulting in better thermal insulation of the cool box. This study gives a better understanding in term of thermal insulation and the results obtained from this study can help with the production of better cool boxes with improved thermal insulation.
- Open Access
- 1 April 2020
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 834 (1) , 012047
Thermal Conductivity and Permeability Studies of Recycle Copper Wire Mesh
Copper is well known as a valuable material, particularly for electrical industries due to its excellent properties. Besides, the price for copper scrap is also higher in comparison with other metal scrap materials found in many electrical appliances such as computer equipment, electric motor, transformer, and other components. This paper describes the potential of recycled copper wire shaped into a form suitable for heat sink application. The samples of wire mesh for this research were fabricated by compacting copper wire with different weight. Compaction was done to form a cylindrical shape with a diameter and height of approximately 25 mm and 30 mm, respectively. These samples were evaluated for porosity, thermal conductivity, and permeability. The experimental results showed that the sample with the lowest porosity exhibited great promising conductivity. In addition, lowering the amount of copper wire in compaction resulted in low density, thus improved its lightweight properties. The greater amount of porosity resulted in greater permeability. The optimum properties with a combination of the excellent thermal conductivity and permeability are necessary for heat sink application to ensure that the parts work effectively.
- 1 April 2020
- Published by IOP Publishing in IOP Conference Series: Materials Science and Engineering
- Vol. 834 (1) , 012047
Open AccessThermal Conductivity and Permeability Studies of Recycle Copper Wire Mesh
Copper is well known as a valuable material, particularly for electrical industries due to its excellent properties. Besides, the price for copper scrap is also higher in comparison with other metal scrap materials found in many electrical appliances such as computer equipment, electric motor, transformer, and other components. This paper describes the potential of recycled copper wire shaped into a form suitable for heat sink application. The samples of wire mesh for this research were fabricated by compacting copper wire with different weight. Compaction was done to form a cylindrical shape with a diameter and height of approximately 25 mm and 30 mm, respectively. These samples were evaluated for porosity, thermal conductivity, and permeability. The experimental results showed that the sample with the lowest porosity exhibited great promising conductivity. In addition, lowering the amount of copper wire in compaction resulted in low density, thus improved its lightweight properties. The greater amount of porosity resulted in greater permeability. The optimum properties with a combination of the excellent thermal conductivity and permeability are necessary for heat sink application to ensure that the parts work effectively.
- 28 September 2015
- Published by Penerbit UTM Press in Jurnal Teknologi (Sciences & Engineering)
- Vol. 76 (9)
EFFECTS OF AIR INTAKE TEMPERATURE ON THE FUEL CONSUMPTION AND EXHAUST EMISSIONS OF NATURAL ASPIRATED GASOLINE ENGINE
Improving fuel consumption with lower exhaust emissions give more focused to all car manufactures. A higher engine performance with lower exhaust emissions requires a complete mixing process resulted in ultra-lean high combustion efficiency. Air intake temperature is one of the alternative strategies to improve fuel consumption and reduced exhaust emissions. This is due to the cold air is denser and contain higher oxygen availability. Air intake temperature will affect to the oxygen concentration in the charged air that influence the combustion process through ignition delay and fuel burning rate. The objective of this experiment is to investigate the effects of air intake temperature to the fuel consumption and exhaust emission at variation of engine speeds and constant load by using 1.6L gasoline engine. Air intake temperature was changed from 20 °C to 30 °C. The DaTAQ Pro V2 software was used to measure the engine fuel consumption while gas analyzer (MRU Gas Analyzer) was used to measure the exhaust emission such as Unburned hydrocarbons (UHCs) and carbon monoxide (CO). The results showed that fuel consumption, UHCs and CO emissions increased with the increase of air intake temperature. The increase of air intake temperature resulted in advanced and shorter combustion duration. Higher oxygen concentration at lower air intake temperature leads to the complete mixing process and complete combustion. Therefore, the experimental results can be concluded that the lower air intake temperature resulted in improved fuel consumption and reduced UHCs and CO emissions.
- 28 September 2015
- Published by Penerbit UTM Press in Jurnal Teknologi (Sciences & Engineering)
- Vol. 76 (9)
EFFECTS OF AIR INTAKE TEMPERATURE ON THE FUEL CONSUMPTION AND EXHAUST EMISSIONS OF NATURAL ASPIRATED GASOLINE ENGINE
Improving fuel consumption with lower exhaust emissions give more focused to all car manufactures. A higher engine performance with lower exhaust emissions requires a complete mixing process resulted in ultra-lean high combustion efficiency. Air intake temperature is one of the alternative strategies to improve fuel consumption and reduced exhaust emissions. This is due to the cold air is denser and contain higher oxygen availability. Air intake temperature will affect to the oxygen concentration in the charged air that influence the combustion process through ignition delay and fuel burning rate. The objective of this experiment is to investigate the effects of air intake temperature to the fuel consumption and exhaust emission at variation of engine speeds and constant load by using 1.6L gasoline engine. Air intake temperature was changed from 20 °C to 30 °C. The DaTAQ Pro V2 software was used to measure the engine fuel consumption while gas analyzer (MRU Gas Analyzer) was used to measure the exhaust emission such as Unburned hydrocarbons (UHCs) and carbon monoxide (CO). The results showed that fuel consumption, UHCs and CO emissions increased with the increase of air intake temperature. The increase of air intake temperature resulted in advanced and shorter combustion duration. Higher oxygen concentration at lower air intake temperature leads to the complete mixing process and complete combustion. Therefore, the experimental results can be concluded that the lower air intake temperature resulted in improved fuel consumption and reduced UHCs and CO emissions.
- 14 September 2015
- Published by Penerbit UTM Press in Jurnal Teknologi (Sciences & Engineering)
- Vol. 76 (5)
EFFECTS OF PALM OIL METHYL ESTER (POME) ON FUEL CONSUMPTION AND EXHAUST EMISSIONS OF DIESEL ENGINE OPERATING WITH BLENDED FUEL (FOSSIL FUEL + JATROPHA OIL METHYL ESTER (JOME))
Biodiesel is used widely as an alternative fuel for diesel engine due to biodegradable, oxygenated, renewable and compatible with diesel engines . In fact, biodiesel emission has decreased the levels of potentially carcinogenic compounds. However, a certain biodiesel such as Jatropha Oil Methyl Ester (JOME) has resulted in the increase of specific fuel consumption and higher NOx emissions. Therefore, the objective of this study is to investigate the effects of Palm Oil Methyl Ester (POME) in the blended fuel (Fossil fuel + JOME) on the fuel consumption and exhaust emission. Experiments were carried out at a constant engine speed (2000 rpm) with variable of engine loads. Results show that the addition of POME leads to the significant reduction in brake specific fuel consumption (BSFC), Total hydrocarbons (THCs), carbon monoxide (CO) and nitrogen dioxide (NOx) emissions. This study shows a huge difference for Total hydrocarbons emission of blends with 5% POME compared to blends with 10% and 15% of POME. Carbon monoxide emission for blends with 15% POME is the lowest at constant engine speed with various engine loads which in average is 53% lower than blends of 5% POME. This is because blends with higher percentage of POME has higher cetane number hence shortened the ignition delay resulted in the lower possibility of formation of rich fuel zone and thus reduces CO emissions. Moreover, the higher percentage of POME also resulted in lower NOx emission regardless of engine loads. The blends with 15% POME had the lowest NOx emission which is 25% less compared with the blends of 5% POME. The study recommended that, additional POME to the blended fuel can be considered as a good initiative to improve blended fuel property for diesel engine due to its potential to improve engine emissions and reduce brake specific fuel consumption. In conclusion, the blends of POME into (Fossil fuel + JOME) improves engine emission without significantly increasing fuel consumption.
- 14 September 2015
- Published by Penerbit UTM Press in Jurnal Teknologi (Sciences & Engineering)
- Vol. 76 (5)
EFFECTS OF PALM OIL METHYL ESTER (POME) ON FUEL CONSUMPTION AND EXHAUST EMISSIONS OF DIESEL ENGINE OPERATING WITH BLENDED FUEL (FOSSIL FUEL + JATROPHA OIL METHYL ESTER (JOME))
Biodiesel is used widely as an alternative fuel for diesel engine due to biodegradable, oxygenated, renewable and compatible with diesel engines . In fact, biodiesel emission has decreased the levels of potentially carcinogenic compounds. However, a certain biodiesel such as Jatropha Oil Methyl Ester (JOME) has resulted in the increase of specific fuel consumption and higher NOx emissions. Therefore, the objective of this study is to investigate the effects of Palm Oil Methyl Ester (POME) in the blended fuel (Fossil fuel + JOME) on the fuel consumption and exhaust emission. Experiments were carried out at a constant engine speed (2000 rpm) with variable of engine loads. Results show that the addition of POME leads to the significant reduction in brake specific fuel consumption (BSFC), Total hydrocarbons (THCs), carbon monoxide (CO) and nitrogen dioxide (NOx) emissions. This study shows a huge difference for Total hydrocarbons emission of blends with 5% POME compared to blends with 10% and 15% of POME. Carbon monoxide emission for blends with 15% POME is the lowest at constant engine speed with various engine loads which in average is 53% lower than blends of 5% POME. This is because blends with higher percentage of POME has higher cetane number hence shortened the ignition delay resulted in the lower possibility of formation of rich fuel zone and thus reduces CO emissions. Moreover, the higher percentage of POME also resulted in lower NOx emission regardless of engine loads. The blends with 15% POME had the lowest NOx emission which is 25% less compared with the blends of 5% POME. The study recommended that, additional POME to the blended fuel can be considered as a good initiative to improve blended fuel property for diesel engine due to its potential to improve engine emissions and reduce brake specific fuel consumption. In conclusion, the blends of POME into (Fossil fuel + JOME) improves engine emission without significantly increasing fuel consumption.
- 20 August 2015
- Published by Penerbit UTM Press in Jurnal Teknologi (Sciences & Engineering)
- Vol. 75 (8)
INVESTIGATION ON CHARACTERISTICS OF POME BLENDED DIESEL ENGINE
The sudden increase in fuel prices due to diminishing petroleum resources and the pollution resulting from its use has resulted in research into alternative fuels such as biodiesel. In addition, the faster combustion and high temperature in the combustion chamber which results from petroleum diesel fuel leads to higher nitrogen oxide (NOx) and Particulate Matter (PM) emissions. Therefore, this research was conducted to investigate the effect of using palm oil methyl ester (POME) blends as alternative fuels on the performance and emission of a compression ignition engine. The performance of POME blends and diesel were compared by manipulating the load of the engine at 1800 rpm. The results obtained show that fuel consumption rate is higher for the POME blends compared to the diesel fuel and increases as the POME concentration increases. The increment of brake specific fuel consumption and the reduction of CO emission exhibit a relation to the increase in percentage of POME. This is mainly contributed by the higher oxygen content of POME which promotes complete combustion of the blends. However, efficient combustion from the blends as compared to diesel fuel resulted from higher oxygen content and cetane number leads to significant increase in exhaust temperature. This in turn increases NOx emissions since using POME blends is highly related to high temperature of combustion chamber. The experimental results proved that POME in compression ignition engine is a possible substitute to diesel.
- 20 August 2015
- Published by Penerbit UTM Press in Jurnal Teknologi (Sciences & Engineering)
- Vol. 75 (8)
INVESTIGATION ON CHARACTERISTICS OF POME BLENDED DIESEL ENGINE
The sudden increase in fuel prices due to diminishing petroleum resources and the pollution resulting from its use has resulted in research into alternative fuels such as biodiesel. In addition, the faster combustion and high temperature in the combustion chamber which results from petroleum diesel fuel leads to higher nitrogen oxide (NOx) and Particulate Matter (PM) emissions. Therefore, this research was conducted to investigate the effect of using palm oil methyl ester (POME) blends as alternative fuels on the performance and emission of a compression ignition engine. The performance of POME blends and diesel were compared by manipulating the load of the engine at 1800 rpm. The results obtained show that fuel consumption rate is higher for the POME blends compared to the diesel fuel and increases as the POME concentration increases. The increment of brake specific fuel consumption and the reduction of CO emission exhibit a relation to the increase in percentage of POME. This is mainly contributed by the higher oxygen content of POME which promotes complete combustion of the blends. However, efficient combustion from the blends as compared to diesel fuel resulted from higher oxygen content and cetane number leads to significant increase in exhaust temperature. This in turn increases NOx emissions since using POME blends is highly related to high temperature of combustion chamber. The experimental results proved that POME in compression ignition engine is a possible substitute to diesel.
- Open Access
- 30 June 2015
- Published by Universiti Malaysia Pahang Al-Sultan Abdullah Press (UMPSA Press) in Journal of Mechanical Engineering and Sciences
- Vol. 8, 1351-1366
A REVIEW OF NANOFLUID ADOPTION IN POLYMER ELECTROLYTE MEMBRANE (PEM) FUEL CELLS AS AN ALTERNATIVE COOLANT
Continuous need for the optimum conversion efficiency of polymer electrolyte membrane fuel cell (PEMFC) operation has triggered varieties of advancements, namely in the thermal management engineering scope. Excellent heat dissipation is correlated with higher performance of a fuel cell, thus increasing its conversion efficiency. This study reveals the potential advancement in thermal engineering of a fuel cell cooling system with respect to nanofluid technology. Nanofluids are seen as a potential evolution of nanotechnology hybridization with the fuel cell serving as a cooling medium. The available literature on the thermophysical properties of potential nanofluids, especially on the electrical conductivity property, has been discussed. The lack of electrical conductivity data for various nanofluids in open literature was another challenge in the application of nanofluids in fuel cells. Unlike in any other thermal management system, a nanofluid in a fuel cell is dealt with using a thermoelectrically active environment. The main challenge in nanofluid adoption in fuel cells was the formulation of a suitable nanofluid coolant with heat transfer enhancement, as compared to its base fluid, but still complying with the strict limits of electrical conductivity as low as 2 mS/cm and several other restrictions discussed by the researchers. It is concluded that a nanofluid in PEMFC is advantageous in terms of both heat transfer and simplification of the cooling system through radiator size reduction and potential elimination of the deionizer as compared to the current PEMFC cooling system. However, there are challenges that need to be well addressed, especially in the electrical conductivity requirement
- 30 June 2015
- Published by Universiti Malaysia Pahang Al-Sultan Abdullah Press (UMPSA Press) in Journal of Mechanical Engineering and Sciences
- Vol. 8, 1351-1366
Open AccessA REVIEW OF NANOFLUID ADOPTION IN POLYMER ELECTROLYTE MEMBRANE (PEM) FUEL CELLS AS AN ALTERNATIVE COOLANT
Continuous need for the optimum conversion efficiency of polymer electrolyte membrane fuel cell (PEMFC) operation has triggered varieties of advancements, namely in the thermal management engineering scope. Excellent heat dissipation is correlated with higher performance of a fuel cell, thus increasing its conversion efficiency. This study reveals the potential advancement in thermal engineering of a fuel cell cooling system with respect to nanofluid technology. Nanofluids are seen as a potential evolution of nanotechnology hybridization with the fuel cell serving as a cooling medium. The available literature on the thermophysical properties of potential nanofluids, especially on the electrical conductivity property, has been discussed. The lack of electrical conductivity data for various nanofluids in open literature was another challenge in the application of nanofluids in fuel cells. Unlike in any other thermal management system, a nanofluid in a fuel cell is dealt with using a thermoelectrically active environment. The main challenge in nanofluid adoption in fuel cells was the formulation of a suitable nanofluid coolant with heat transfer enhancement, as compared to its base fluid, but still complying with the strict limits of electrical conductivity as low as 2 mS/cm and several other restrictions discussed by the researchers. It is concluded that a nanofluid in PEMFC is advantageous in terms of both heat transfer and simplification of the cooling system through radiator size reduction and potential elimination of the deionizer as compared to the current PEMFC cooling system. However, there are challenges that need to be well addressed, especially in the electrical conductivity requirement
- 1 November 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 641-646
Thermal and electrical experimental characterization of Ethylene Glycol and water mixture nanofluids for a 400w Proton Exchange Membrane Fuel Cell
Nanofluid is an emerging technology in heat transfer study. The effect of nanofluids as a cooling medium in liquid cooled Proton Exchange Membrane Fuel Cell (PEMFC) is studied. Nanofluids with 0.1% and 0.5% volume concentration of Al2O3 are dispersed in base fluid of 50:50 mixture of Ethylene Glycol and water were analyzed experimentally. A rated power of 400 W liquid cooled PEMFC was used to verify the findings. The result showed that insignificant improvement in performance of PEMFC with nanofluids through polarization curve findings, perhaps due to the lower wattage of PEMFC used. The advantage of nanofluids utilization in PEMFC might be visible in higher wattage of PEMFC due to higher working fluid temperature. Higher thermal conductivity of nanofluid at higher temperature is expected to give advantage in terms of polarization curve of a PEMFC. However, the thermal performance is improved through the heat transfer rate increment of 68.5 % and 46 % for both 0.5 % of Al2O3 nanofluid and 0.1 % of Al2O3 nanofluid respectively.
- 1 November 2014
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 641-646
Thermal and electrical experimental characterization of Ethylene Glycol and water mixture nanofluids for a 400w Proton Exchange Membrane Fuel Cell
Nanofluid is an emerging technology in heat transfer study. The effect of nanofluids as a cooling medium in liquid cooled Proton Exchange Membrane Fuel Cell (PEMFC) is studied. Nanofluids with 0.1% and 0.5% volume concentration of Al2O3 are dispersed in base fluid of 50:50 mixture of Ethylene Glycol and water were analyzed experimentally. A rated power of 400 W liquid cooled PEMFC was used to verify the findings. The result showed that insignificant improvement in performance of PEMFC with nanofluids through polarization curve findings, perhaps due to the lower wattage of PEMFC used. The advantage of nanofluids utilization in PEMFC might be visible in higher wattage of PEMFC due to higher working fluid temperature. Higher thermal conductivity of nanofluid at higher temperature is expected to give advantage in terms of polarization curve of a PEMFC. However, the thermal performance is improved through the heat transfer rate increment of 68.5 % and 46 % for both 0.5 % of Al2O3 nanofluid and 0.1 % of Al2O3 nanofluid respectively.
- 31 October 2014
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 660, 391-396
Thermal and Electrical Experimental Characterization of Ethylene Glycol and Water Mixture Coolants for a 400 W Proton Exchange Membrane Fuel
Nanofluid is an emerging technology in heat transfer study. The effect of nanofluids as a cooling medium in Proton Exchange Membrane Fuel Cell (PEMFC) is studied. Nanofluids with 0.1% and 0.5% of Al2O3 dispersed in base fluid of 50:50 mixture of Ethylene Glycol and water were analyzed experimentally. A 400 W liquid cooled PEMFC was used to verify the findings. The result showed that insignificant improvement in performance of PEMFC with nanofluids, perhaps due to the lower wattage of PEMFC used. However, the thermal performance is improved through the heat transfer rate increment of 68.5 % and 46 % for both 0.5 % of Al2O3 nanofluid and 0.1 % of Al2O3 nanofluid respectively.
- 31 October 2014
- Published by Trans Tech Publications, Ltd. in Applied Mechanics and Materials
- Vol. 660, 391-396
Thermal and Electrical Experimental Characterization of Ethylene Glycol and Water Mixture Coolants for a 400 W Proton Exchange Membrane Fuel
Nanofluid is an emerging technology in heat transfer study. The effect of nanofluids as a cooling medium in Proton Exchange Membrane Fuel Cell (PEMFC) is studied. Nanofluids with 0.1% and 0.5% of Al2O3 dispersed in base fluid of 50:50 mixture of Ethylene Glycol and water were analyzed experimentally. A 400 W liquid cooled PEMFC was used to verify the findings. The result showed that insignificant improvement in performance of PEMFC with nanofluids, perhaps due to the lower wattage of PEMFC used. However, the thermal performance is improved through the heat transfer rate increment of 68.5 % and 46 % for both 0.5 % of Al2O3 nanofluid and 0.1 % of Al2O3 nanofluid respectively.