Ying Ma
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ying Ma has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Guirong Yang
School of Materials Science and Engineering, Lanzhou University of Technology, Lanzhou 730050, China
3 shared publications - Ouyang Li
School of Materials Science and Engineering, Lanzhou University of Technology, Lanzhou 730050, China
3 shared publications - Wenming Song
Machinery Industry Shanghai Lanya Petrochemical Equipment Inspection Ltd., Lanzhou 730070, China
3 shared publications - Yushun Wang
Qinghai Provincial Key Laboratory of Nanomaterials and Technology, Qinghai Minzu University, Xining 810007, China
1 shared publication - Zhanying Wang
Qinghai Provincial Key Laboratory of Nanomaterials and Technology, School of Chemistry and Materials Science, Qinghai Minzu University, Xining 810007, China
1 shared publication
Latest Publications
- Open Access
- 25 October 2025
- Published by MDPI AG in Lubricants
- Vol. 13 (11) , 473
Thermal Cycling Tribological Behavior and Its Evolution of hBN-Reinforced Ni/WC/CeO2 Cladding Layers from 25 to 600 °C
Enhancing the high-temperature tribological performance of protective claddings is crucial for demanding industrial applications. This study focuses on developing hexagonal boron nitride (hBN)-reinforced Ni-based composite claddings to improve wear resistance over a wide temperature range. Ni/WC/CeO2 cladding layers with varying hBN contents (0.25 wt% and 0.75 wt%) were fabricated on 45 steel substrates via vacuum cladding. Their microstructure, mechanical properties, and tribological behavior under thermal cycling (25–600 °C) were systematically evaluated. Results reveal that the in situ formation of a hard Cr2B phase, coupled with hBN addition, was key to achieving optimal overall properties. The composite with 0.25 wt% hBN (NWB25) demonstrated optimal overall properties, featuring the lowest porosity (0.1813%) and the highest H/E ratio (0.0405), leading to the best overall tribological performance. A distinct transition from mild to severe wear was observed during the 300 °C-2 stage, resulting from the fracture of a high-temperature tribo-oxidative layer. An hBN content of 0.25 wt% is identified as optimal for balancing solid lubrication and matrix cohesion, thereby achieving superior thermal cycling wear resistance. Higher hBN concentrations promote grain coarsening and increased porosity, which degrade performance.
- 25 October 2025
- Published by MDPI AG in Lubricants
- Vol. 13 (11) , 473
Open AccessThermal Cycling Tribological Behavior and Its Evolution of hBN-Reinforced Ni/WC/CeO2 Cladding Layers from 25 to 600 °C
Enhancing the high-temperature tribological performance of protective claddings is crucial for demanding industrial applications. This study focuses on developing hexagonal boron nitride (hBN)-reinforced Ni-based composite claddings to improve wear resistance over a wide temperature range. Ni/WC/CeO2 cladding layers with varying hBN contents (0.25 wt% and 0.75 wt%) were fabricated on 45 steel substrates via vacuum cladding. Their microstructure, mechanical properties, and tribological behavior under thermal cycling (25–600 °C) were systematically evaluated. Results reveal that the in situ formation of a hard Cr2B phase, coupled with hBN addition, was key to achieving optimal overall properties. The composite with 0.25 wt% hBN (NWB25) demonstrated optimal overall properties, featuring the lowest porosity (0.1813%) and the highest H/E ratio (0.0405), leading to the best overall tribological performance. A distinct transition from mild to severe wear was observed during the 300 °C-2 stage, resulting from the fracture of a high-temperature tribo-oxidative layer. An hBN content of 0.25 wt% is identified as optimal for balancing solid lubrication and matrix cohesion, thereby achieving superior thermal cycling wear resistance. Higher hBN concentrations promote grain coarsening and increased porosity, which degrade performance.
- Open Access
Surface Friction and Interfacial Wear Mechanisms in CeO2-Ni/WC Cladding Layers on 45 Steel
This study investigates the insufficient surface hardness of medium-carbon 45 steel and the drawbacks associated with conventional surface modification techniques (e.g., cracking in laser cladding, weak bonding in thermal spraying, restricted thickness in chemical deposition). Series CeO2-Ni/WC composite claddings (with CeO2 content ranging from 0.5 to 2.0 wt %) were fabricated via vacuum cladding. The cladding with 0.5 wt % CeO2 (NWC5) exhibited the lowest porosity (0.0673%) and finest grain size (12.06 nm) and demonstrated the highest microhardness (1042.74 HV0.2) and elastic modulus (269.06 GPa), respectively. The interfacial friction coefficient (0.343–0.444) was significantly reduced compared to the surface friction coefficient (0.562–0.617). Wear track analysis revealed that the width in the cladding layer-to-substrate transition zone (CTSZ) was 22.1–43.2% wider than that in the substrate-to-cladding layer transition zone (STCZ). This disparity is attributed to stress concentration induced by the abrupt hardness change across the CTSZ, promoting the formation of a three-tiered step structure (with a step height difference of 2.1–4.1 µm). In contrast, the progressive hardness series in the STCZ facilitated a smoother wear surface. The dominant wear mechanism was identified as a combination of abrasive and oxidative wear. This study provides a theoretical foundation for optimizing such high-reliability components.
Open AccessSurface Friction and Interfacial Wear Mechanisms in CeO2-Ni/WC Cladding Layers on 45 Steel
This study investigates the insufficient surface hardness of medium-carbon 45 steel and the drawbacks associated with conventional surface modification techniques (e.g., cracking in laser cladding, weak bonding in thermal spraying, restricted thickness in chemical deposition). Series CeO2-Ni/WC composite claddings (with CeO2 content ranging from 0.5 to 2.0 wt %) were fabricated via vacuum cladding. The cladding with 0.5 wt % CeO2 (NWC5) exhibited the lowest porosity (0.0673%) and finest grain size (12.06 nm) and demonstrated the highest microhardness (1042.74 HV0.2) and elastic modulus (269.06 GPa), respectively. The interfacial friction coefficient (0.343–0.444) was significantly reduced compared to the surface friction coefficient (0.562–0.617). Wear track analysis revealed that the width in the cladding layer-to-substrate transition zone (CTSZ) was 22.1–43.2% wider than that in the substrate-to-cladding layer transition zone (STCZ). This disparity is attributed to stress concentration induced by the abrupt hardness change across the CTSZ, promoting the formation of a three-tiered step structure (with a step height difference of 2.1–4.1 µm). In contrast, the progressive hardness series in the STCZ facilitated a smoother wear surface. The dominant wear mechanism was identified as a combination of abrasive and oxidative wear. This study provides a theoretical foundation for optimizing such high-reliability components.
- Open Access
Effect of Fluorinated Graphite (FG) Addition on Friction Performance of FG-Ni/WC/CeO2 Cladding Layers over a Wide Temperature Range
This study fabricated fluorinated graphite (FG)-reinforced Ni/WC/CeO2 cladding layers on 45 steel substrates using vacuum cladding technology. Their microstructure, phase composition, mechanical properties, and tribological behavior over a wide temperature range (25–800 °C) were systematically characterized. The results demonstrate that FG addition promotes the formation of a self-lubricating CeF3 phase. The optimal CeF3 phase formation efficiency occurred at a 1.5 wt% FG content (NWF15). The NWF15 cladding layer exhibited the smallest average grain size (15.88 nm) and the lowest porosity (0.1410%) among all samples. Mechanical testing revealed that this cladding layer possessed the highest microhardness (1062.7 ± 21.9 HV0.2). Its H/E and H3/E2 ratios, indicative of resistance to elastic strain and plastic deformation, reached 0.0489 and 0.0291, respectively. Tribological tests revealed pronounced temperature-dependent wear behavior: abrasive wear was predominant at 25 °C; adhesive wear dominated from 200 to 600 °C; and oxidative wear became the primary mechanism at 800 °C. Throughout this temperature range, the CeF3 phase effectively reduced wear damage by suppressing groove propagation and providing effective lubrication, particularly under high-temperature conditions.
Open AccessEffect of Fluorinated Graphite (FG) Addition on Friction Performance of FG-Ni/WC/CeO2 Cladding Layers over a Wide Temperature Range
This study fabricated fluorinated graphite (FG)-reinforced Ni/WC/CeO2 cladding layers on 45 steel substrates using vacuum cladding technology. Their microstructure, phase composition, mechanical properties, and tribological behavior over a wide temperature range (25–800 °C) were systematically characterized. The results demonstrate that FG addition promotes the formation of a self-lubricating CeF3 phase. The optimal CeF3 phase formation efficiency occurred at a 1.5 wt% FG content (NWF15). The NWF15 cladding layer exhibited the smallest average grain size (15.88 nm) and the lowest porosity (0.1410%) among all samples. Mechanical testing revealed that this cladding layer possessed the highest microhardness (1062.7 ± 21.9 HV0.2). Its H/E and H3/E2 ratios, indicative of resistance to elastic strain and plastic deformation, reached 0.0489 and 0.0291, respectively. Tribological tests revealed pronounced temperature-dependent wear behavior: abrasive wear was predominant at 25 °C; adhesive wear dominated from 200 to 600 °C; and oxidative wear became the primary mechanism at 800 °C. Throughout this temperature range, the CeF3 phase effectively reduced wear damage by suppressing groove propagation and providing effective lubrication, particularly under high-temperature conditions.
- Open Access
Effect of V2O5 Additive on Micro-Arc Oxidation Coatings Fabricated on Magnesium Alloys with Different Loading Voltages
Effect of V2O5 additive in silicate-containing electrolyte on AZ91D magnesium alloys treated by micro-arc oxidation (MAO) technology under different loading voltages was investigated. The results showed that vanadium was well up-taken into the coating chemically. Moreover, a new phase of MgV2O4 with spinel structure was obtained in MAO coatings due to V2O5 added into the electrolyte. The MgV2O4 phase was responsible for the coatings exhibiting brown color and also was beneficial to improving the anti-corrosion property. In spotting tests, the corrosion resistances of coatings prepared under the high voltage are about 6–9 times higher than those of the low voltage because of the thicker coatings of the former. In potentiodynamic polarization tests, the coatings’ corrosion resistances were improved with the addition of V2O5, which was more significant under the low voltage than that under the high voltage. When the concentration of V2O5 was 0.2 g/L, the corrosion current density of the coating was the lowest, which means that the coating’s corrosion resistance under the low voltage is the best. Hence, it is necessary to carry out targeted design of the coating’s microstructure according to the different applications.
Open AccessEffect of V2O5 Additive on Micro-Arc Oxidation Coatings Fabricated on Magnesium Alloys with Different Loading Voltages
Effect of V2O5 additive in silicate-containing electrolyte on AZ91D magnesium alloys treated by micro-arc oxidation (MAO) technology under different loading voltages was investigated. The results showed that vanadium was well up-taken into the coating chemically. Moreover, a new phase of MgV2O4 with spinel structure was obtained in MAO coatings due to V2O5 added into the electrolyte. The MgV2O4 phase was responsible for the coatings exhibiting brown color and also was beneficial to improving the anti-corrosion property. In spotting tests, the corrosion resistances of coatings prepared under the high voltage are about 6–9 times higher than those of the low voltage because of the thicker coatings of the former. In potentiodynamic polarization tests, the coatings’ corrosion resistances were improved with the addition of V2O5, which was more significant under the low voltage than that under the high voltage. When the concentration of V2O5 was 0.2 g/L, the corrosion current density of the coating was the lowest, which means that the coating’s corrosion resistance under the low voltage is the best. Hence, it is necessary to carry out targeted design of the coating’s microstructure according to the different applications.