Jülide Hızal

This study investigates the mechanical, thermal, and surface characteristics of acrylonitrile–butadiene–styrene (ABS) composites reinforced with bentonite and bis(2‐ethylhexyl) phosphate (DEHPA)‐modified bentonite. The addition of bentonite significantly reduced the tensile strength and elongation at break due to the filler's inherent brittleness. Pure ABS exhibited a tensile strength of 42.2 MPa, which decreased by 16.1% with the incorporation of 20% bentonite (ABS1). Impact strength tests showed that the inclusion of bentonite lowered impact resistance, particularly in notched samples. Bentonite also increased the hardness and density, reflecting improved rigidity but reduced flexibility. Surface gloss changed from semigloss to matte, and FT‐IR spectroscopy confirmed the successful integration of bentonite. Water absorption tests revealed that DEHPA‐modified bentonite composites had higher absorption over time, highlighting the modification's effect on hydrophilicity. While bentonite improves certain properties, the balance between mechanical strength and flexibility needs to be further explored to meet the requirements of specific applications such as automotive components, electronics casings, and construction materials.

This study deals with the investigation of cyfluthrin, cypermethrin, deltamethrin, and malathion residues in local honey samples from Gümüşhane, Turkey. The determination was performed with GC/MS-MS method with HP-5MS column under certain conditions: 120 ℃ oven temperature, 250 ℃ injection temperature, 121.9 kPa pressure and 1.2-1.8 mL/min flow rates. The samples were picked from eighteen stations of Gümüşhane. Standard addition method was employed in chromatographic determination. No pesticide detected in samples of fifteen stations, nevertheless, subjected pesticides were determined in samples collected from other three stations. The residue levels varied from 0.18 mg/kg to 9.50 mg/kg at 1.5 mL/min flow rate. The results were also evaluated with Box-Behnken Design (BBD) optimization. Multivariate experimental design (flow rate and station, pesticide type) was employed for constructing quadratic models. Regression analysis showed that the experimental results and the predictive values yielded by model are quite close to each other with determination coefficient (R2) of 0.985.

A reusable, low–cost, and convenient ethylenediamine (EDA)–bound magnetite nanoparticles (MNPs)–based colorimetric sensor has been developed for dual function colorimetric determination of nitroaromatic explosives such as TNT and tetryl. Colorimetric detection of analytes may occur through two independent routes: (1) nano−Fe₃O₄− EDA− NH₂ as σ−donor may interact with the σ− and π−acceptor aromatic−poly(NO₂) groups to produce a colored charge−transfer (CT) complex; (2) nano−Fe₃O₄−EDA−NH₂ as a Fenton-type nanozyme may generate reactive species that comprise hydroxyl radicals (^•OH) with H₂O₂ to oxidize 3,3′,5,5′–tetramethylbenzidine (TMB) to a blue-colored diimine (oxTMB−TMB) CT complex, where this color is bleached with TNT/tetryl because of donor−acceptor interactions between the explosive –NO₂ groups and the –NH₂ group of Fe₃O₄−EDA nanoparticles of restricted nanozyme activity. Both methods can quantify TNT well below the EPA recommended TNT residential screening level in soil, LOD being in the micromolar range. As EDA was covalently bound to MNPs, the same sensor can be separately reused six times for TNT and eight times for tetryl determination, using method (1). Common metal ions, anions, energetic materials, several camouflage materials, and soil components such as humates did not interfere with the nanosensor performance for TNT and tetryl. The combination of charge−transfer and nanozyme ability of Fe₃O₄− EDA−NH₂ nanoparticles may bring a new approach to dual function colorimetric sensor design. To the best of our knowledge, this is the first dual function colorimetric sensor for TNT and tetryl using the same nanoparticles as sensing elements in two different detection systems involving either formation or bleaching of colored species. Graphical abstract The proposed colorimetric sensor can determine nitroaromatic explosives in two different ways: method−1 for TNT and tetryl sensing with EDA–MNPs relies on the donor–acceptor interaction between the electron–deficient nitroaromatics and electron–rich amine groups covalently functionalized on MNPs to produce an absorbance at 512 nm. In method−2, EDA–MNPs having nanozyme activity react with H₂O₂ to form reactive species that can oxidize TMB to its blue–colored charge–transfer (CT) complex, where TNT and tetryl addition may partially inhibit the nanozyme activity of EDA–MNPs and cause color bleaching (decrement of 650 nm absorbance) by disrupting the CT complex formed from TMB. This is the first dual function colorimetric sensor for nitro explosives uniquely combining charge-transfer and nanozyme ability of EDA–Fe₃O₄ nanoparticles in the same nano-sensor.