HYHaiyang Yu

Haiyang Yu

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Haiyang Yu has a total of 86 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    In situ micro-CT quantification of residual-oil morphology evolution and pore-size-resolved recovery contributions during water flooding in a low-permeability sandstone

    by Yu Haiyang, Yiting Lu, Jicheng Zhang, Ruibo Zhang, Li Dong, Hongbao Wang

    Residual oil in mature low-permeability sandstone reservoirs becomes progressively disconnected during water flooding, yet the coupled evolution of oil morphology, pore size, and recovery contribution remains insufficiently quantified. A low-permeability sandstone plug from the Qian'an Oilfield, Songliao Basin, China, was imaged by in situ micro-CT in the initial oil-bearing state and after 1 and 10 pore volumes (PV) of water injection. Rigid registration, differential imaging, phase segmentation, pore-network extraction, and connected-component analysis were used to quantify oil-water redistribution and classify oil bodies as clustered, porous, columnar, droplet, or film-like. An internally closed volume-accounting framework was used: exhaustive, non-overlapping pore-radius classes summed to cumulative recovery, and recovery recalculated from the rounded saturation values differed from the registered-volume result by less than 0.5 percentage points. Cumulative oil recovery reached 41.04% at 1 PV and 65.66% at 10 PV. Clustered oil was preferentially removed during early flooding, whereas porous and columnar oil became the principal residual morphologies after water breakthrough. Recovery contributions were concentrated mainly in pores with radii of 20-90 μm and peaked near 45-50 μm; pores below 20 μm contributed little under the present imaging and displacement conditions. The transition from extended clusters to multi-pore and isolated oil bodies is consistent with changes in pore-network accessibility, snap-off, and capillary trapping. The relationships are specific to the analyzed core and nominal 2.03 μm resolution, and further validation using additional cores is recommended.

  • Open Access

    Multi-scale Occurrence and Evolution Laws of Microscopic Residual Oil and Quantitative Regulation Mechanism of Oil Recovery Efficiency during Water Flooding

    by Yu Haiyang, Yiting Lu, Jicheng Zhang, Ruibo Zhang, Li Dong, Hongbao Wang

    Major onshore sandstone oil reservoirs in China have generally entered the development stage of high water cut and high recovery degree, in which fine-scale residual oil tapping has become a critical measure to safeguard national oil and gas supply security and sustainably improve water flooding oil recovery efficiency of oilfields. To unravel the dynamic evolution laws of residual oil morphology during water flooding and its intrinsic coupling relationship with pore-throat structure, this study takes low-permeability sandstone core samples and adopts an integrated methodology combining in-situ micro-CT scanning technology with core water flooding physical simulation, and systematically conducts quantitative characterization of microscopic residual oil distribution under different injected pore volume (PV) conditions. Through high-precision image registration, image subtraction and digital core analysis technology, we achieved three-dimensional visualization and quantitative characterization of core pore-throat structure and oil-water distribution at different water flooding stages. Based on geometric and topological parameters, we classified microscopic residual oil into five morphological types and systematically revealed their staged evolution laws with increasing injected PV. With the advancement of water flooding, water flooding oil recovery efficiency gradually increases to 65.66%, accompanied by an ordered sequential evolution of residual oil morphology: from interconnected clustered residual oil dominated in large pores, to trapped porous and columnar residual oil prevailing in medium pores, and finally to discrete droplet residual oil confined in micropores. The medium-to-large pores with a radius of 20~90μm are identified as the dominant interval for crude oil mobilization, while the peak occurrence pore radius of residual oil with different morphologies shifts to smaller scales as water flooding progresses. This study elucidates the dynamic evolution mechanism of residual oil occurrence morphology and its coupling relationship with pore-throat structure at the pore scale, and provides a critical theoretical basis for accurate residual oil prediction and enhanced oil recovery strategy optimization.

  • Open Access

    Multi-scale Occurrence and Evolution Laws of Microscopic Residual Oil and Quantitative Regulation Mechanism of Oil Recovery Efficiency during Water Flooding

    by Yu Haiyang, Yiting Lu, Jicheng Zhang, Ruibo Zhang, Li Dong, Hongbao Wang

    Major onshore sandstone oil reservoirs in China have generally entered the development stage of high water cut and high recovery degree, in which fine-scale residual oil tapping has become a critical measure to safeguard national oil and gas supply security and sustainably improve water flooding oil recovery efficiency of oilfields. To unravel the dynamic evolution laws of residual oil morphology during water flooding and its intrinsic coupling relationship with pore-throat structure, this study takes low-permeability sandstone core samples from the Qian'an Oilfield, Songliao Basin, China as the research object, adopts an integrated methodology combining in-situ micro-CT scanning technology with core water flooding physical simulation, and systematically conducts quantitative characterization of microscopic residual oil distribution under different injected pore volume (PV) conditions. Through high-precision image registration, image subtraction and digital core analysis technology, we achieved three-dimensional (3D) visualization and quantitative characterization of core pore-throat structure and oil-water distribution at different water flooding stages. Based on geometric and topological parameters, we classified microscopic residual oil into five morphological types, namely clustered, porous, columnar, droplet and film-like residual oil, and systematically revealed their staged evolution laws with increasing injected PV. The results demonstrate that with the advancement of water flooding, water flooding oil recovery efficiency gradually increases to 65.66%, accompanied by an ordered sequential evolution of residual oil morphology: from interconnected clustered residual oil dominated in large pores, to trapped porous and columnar residual oil prevailing in medium pores, and finally to discrete droplet residual oil confined in micropores. The medium-to-large pores with a radius of 20~90μm are identified as the dominant interval for crude oil mobilization, while the peak occurrence pore radius of residual oil with different morphologies shifts to smaller scales as water flooding progresses. This study elucidates the dynamic evolution mechanism of residual oil occurrence morphology and its coupling relationship with pore-throat structure at the pore scale, and provides a critical theoretical basis for accurate residual oil prediction and enhanced oil recovery (EOR) strategy optimization in low-permeability sandstone reservoirs.

  • Development, characterization, and performance evaluation of a sodium silicate-based CO2-enhanced sequestration system for deep coal reservoirs

    by Hongbao Wang, Haiyang Yu, Weiqiang Song, Wei Zhang, Rumei Yang, Yiting Lu, Yufeng Lin, Xinrui Jiang

  • Study on the law of waterflooding enhancement in tight reservoirs

    by Weiqiang Song, Guangzhi Zhao, Haiyang Yu, Hui Huang, Jianbo Wang, Kezhan Wang, Yonggang Li, Dong Li, Bin Yuan

    Waterflooding is widely used to enhance formation pore pressure and oil recovery, which is crucial to determine the waterflooding timing with varying injection rate. This paper proposed an experimental method to illustrate the variation law of micro-pores in rocks during waterflooding using online nuclear magnetic resonance and dynamic computed tomography scanning. A theoretical model is used to optimize the waterflooding time depending on the effective porosity and pressure propagation velocity. The results show that, when subjected to confining pressure, the pores and cracks inside the rock sample are compressed, resulting in decreased permeability. Under reasonable confining pressure, the small pores can be increased to the largest by 121.60%. By controlling the water injection pressure, the quantity and proportion of large and small pores in the reservoir rock mass can be regulated and then the permeability of the reservoir can be quantitatively and controllably increased, ensuring the feasibility of increasing the waterflooding in improving the oil and gas recovery. Considering effective porosity and pressure propagation velocity, the timing of water injection is deduced. Based on the laboratory experiments and theoretical derivations, this paper proposes a method for determining the optimal water injection time, which helps to solve the problem of process parameter design of waterflooding and gives an increased recovery of the three adopters by 18%–35%. This study provides theoretical support and practical guidance for the waterflooding development of tight oil reservoirs.


  • Permeability evolution in variably saturated shales controlled by bimodal organic/inorganic pore structure and surface wetting characteristics

    by Kunkun Fan, Haiyang Yu, Derek Elsworth, Shaojie Chen, Xiang Ge, Huanfu Du

    Moisture is distributed heterogeneously within shale with distinctive features in both organic and inorganic pores. Importantly, this influences gas flow, impacts reservoir dynamics, and affects the accuracy of production forecasts. We establish a variable pressure gradient-bimodal pore structure (VPG-BPS) model to capture these characteristics of methane transport in partially water-saturated shale. We determine permeability in both organic and inorganic pores by matching estimated to actual gas production. Dynamic production experiments are conducted on variably saturated shales from the Sichuan Basin to determine permeability. Methane adsorption capacities are categorized into three stages, delineated by two intermediate threshold moisture contents—lower (MLc) and upper (MUc) threshold moisture contents, respectively. We demonstrate that the moisture content significantly influences shale transport dynamics by controlling adsorption–desorption properties and thereby gas-water distribution and permeability. Ultimate gas production decreases with increasing moisture content (Mc). Gas permeability (Kin and Ko) and gas desorption rate coefficients (kads,in and kads,o) in inorganic and organic pores range from 1 × 10−8 μm2 to 1 × 10−7 μm2, and 1 × 10−4 to 1 × 10−3, respectively. With Mc increasing from 0% to 3.5% (MUc), Kin, Ko, and kads,in exhibit a consistent trend of initially increasing before decreasing although kads,in shows no definitive trend above the threshold peak (MLc). When Mc increases from 0% to 2.2% (MLc), the desorptive hysteretic effect gradually weakens and adsorption kads,in increases with increasing Mc, subsequently prompting an increase in the other three flow parameters. As Mc further increases to MUc, kads,in remains constant but the other three flow parameters decrease as the gas flow channel is occupied by the invading water. Even when moisture migration ignored, the VPG-BPS model provides superior predictions of time histories of gas production over existing models and thus provides a theoretical foundation for dynamic evaluation of shale gas production.

  • Open Access

    Real-time automatic identification methods for downhole whirling based on mechanical specific energy model of drill bit

    by Weiqiang Song, Huidong Mu, Haiyang Yu, Guangzhi Zhao, Lulin Kong, Xue Sun, Zhiwei Sun

    In the drilling exploitation of hot dry rock for geothermal energy, whirling is one of the main low-efficiency conditions that affect the efficiency of Polycrystalline Diamond Compact (PDC) bit in horizontal well drilling. Realizing automatic and real-time identification with whirling is of great significance to save non-productive time and ensure drilling safety and benefit. In this paper, we first constructed a real-time drilling mechanical specific energy (MSE) model combined with while-drilling testing to reflect the real-time drilling conditions. The MSE model is used to normalize multi-source parameters. Secondly, we constructed a Back Propagation (BP) artificial neural network (ANN), and then the normalization effect verification, optimization of network parameters, and identification effect verification of whirling were carried out. The final results show that the established MSE model has a favourable effect on data normalization, which could also reduce the complexity of the required network model, and shorten the training time by 20–30 s/step. The optimal algorithm is Trainscg, whose optimal number of hidden layer nodes is 5, and the optimal maximum number of iteration steps is 1000. The established ANN model can accurately identify whirling based on MSE, the accuracy is about 0.94, and the average relative error is 1.3%. The method established in this paper provides a reference for the automatic identification of various low-efficiency conditions based on MSE.


  • Open Access

    A Study on the Plugging Effect of Different Plugging Agent Combinations during CO2 Flooding in Heterogeneous Reservoirs

    by Xuetong Zhang, Wenjuan Ji, Haiyang Yu, Yilin Li, Fei Yan, Weiqiang Song, Xinrui Jiang, Hongbao Wang

    Gas channeling control is key to improving CO2-flooding efficiency. A traditional plugging system has disadvantages, such as poor adaptability and stability, leading to the poor plugging effect of CO2 channeling in heterogeneous reservoirs and difficulty in controlling the subsequent CO2 injection pressure. To achieve a significant plugging effect and effectively control the subsequent CO2 injection pressure, a heterogeneous physical model of gas channeling in a horizontal well was established, and plugging experiments were conducted using four different combinations of plugging agents during CO2 flooding. Three evaluation parameters were defined, including the temperature field variation coefficient (TFVC), medium-permeability diversion rate (MPDR), and subsequent injection pressure coefficient (SIPC). The plugging effect of different combinations of plugging agents during CO2 flooding in heterogeneous reservoirs was analyzed. The results show that the plugging effect after using a combination of plugging agents was significantly better than after using a single plugging agent, and different plugging agent combinations had distinct characteristics. The strong–medium–weak (S-M-W) combination had the best MPDR for subsequent CO2 flooding, but the SIPC was the highest. The strong–weak–strong–weak (S-W-S-W) and weak–strong–weak–strong (W-S-W-S) combinations could effectively control the SIPC. These results indicate that plugging using the S-W-S-W and W-S-W-S combinations can achieve an effective plugging effect and reasonably control the subsequent CO2 injection pressure. This work provides a personalized design scheme for effective gas channeling control and maintenance of appropriate injection pressure during CO2 flooding in heterogeneous reservoirs.


  • Open Access

    Effect of Polymer and Crosslinker Concentration on Static and Dynamic Gelation Behavior of Phenolic Resin Hydrogel

    by Wenjuan Ji, Bei Chang, Haiyang Yu, Yilin Li, Weiqiang Song

    The application results of profile control and water plugging technology are highly related to the gelation time and strength of phenolic resin hydrogel. In this work, a hydrogel solution was prepared by fully mixing the prepared polymer solution with a crosslinker. The static gelation process of PFR hydrogel in ampoule bottles and porous media was analyzed by changes in the viscosity and residual resistance coefficient. Then, the dynamic gelation of the PFR hydrogel in porous media was tested using a circulating flow device, and the changes in viscosity and injection pressure were analyzed during the dynamic gelation process. Finally, the effects of the polymer concentration and crosslinker concentration on dynamic gelation were analyzed. The initial gelation time and final gelation time in porous media were 1–1.5 times and 1.5–2 times those in ampoule bottles under static conditions, respectively. The initial dynamic gelation time in porous media was 2–2.5 times and 1.5–2 times the initial static gelation times in ampoule bottles and porous media, respectively. The final dynamic gelation time was four times and two times the initial static gelation times in ampoule bottles and porous media, respectively. The production after dynamic gelation in porous media comprised hydrogel aggregates and water fluid, leading to a high injection pressure and low viscosity of the produced liquid. As the concentration of polymer and crosslinker increased, the dynamic gelation time was shortened and the gel strength was increased. In the dynamic gelation process in porous media, the phenol resin hydrogel could migrate deeply, but it was limited by the concentrations of the polymer and crosslinker. The results of subsequent water flooding showed that the polymer hydrogel had a good plugging ability after dynamic gelation. The deep reservoir could only be blocked off in the subsequent water flooding process when the migration of hydrogel happened in the dynamic gelation process.


  • Open Access

    Quantitative Evaluation of Pre-Drilling Safety by Combining Analytic Hierarchy Process with Alternating Condition Expectation

    by Kunkun Fan, Shankai Sun, Haiyang Yu, Wenbin Sun, Hai Lin, Chunguang Wang, Shugang Hou, Huanfu Du, Dong Chen, Jia He

    In order to avoid potential personnel and financial losses, the evaluation of pre-drilling safety is of great importance in oil and gas exploration and development. This paper presents a method of evaluating pre-drilling safety through combining the Analytic Hierarchy Process (AHP) with the Alternating Condition Expectation (ACE) method. An indicator system with a 9-3-1 structure was established, incorporating various unrestricted variables to describe the technical factor. Additionally, nine membership functions and weights were determined in order to build the AHP model by connecting the independent variables in the basic layer to dependent variables in the middle layer. Four transformed functions were also formulated to construct the ACE model by linking the middle variables to the pre-drilling safety value in the final layer. A total of 28 sets of on-site drilling data from three oilfields were collected for the establishment and verification of the AHP-ACE model. Average absolute error (AAE) and average absolute relative error (AARE) of the model to predict the training data are 0.03 and 4.29%, respectively, whereas the AAE and AARE for verification samples are 0.03 and 4.51%, respectively. The sensitivity ranking of the three potential variables is as follows: human factor exhibits the highest degree of sensitivity, followed by natural factor and technical factor, in descending order. The AHP-ACE model for pre-drilling safety assessment faces limitations in universal applicability and scope, particularly in real-time drilling activities. However, its potential for improvement lies in integrating insights from past operations and expanding the dataset to enhance accuracy and broaden safety assessment coverage. This method is not limited by blocks, which is of great significance to ensure drilling safety.