Wenjuan Ji
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Wenjuan Ji has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Haiyang Yu
College of Energy and Mining Engineering, Shandong University of Science and Technology, Qingdao 266590, China
4 shared publications - Weiqiang Song
College of Energy and Mining Engineering, Shandong University of Science and Technology, Qingdao 266590, China
3 shared publications - Yilin Li
Drilling & Production Technology Research Institute of Jidong Oilfield, China National Petroleum Corporation Limited, Tangshan 063000, China
2 shared publications - Bei Chang
Chuanqing Drilling Engineering Company Limited, China National Petroleum Corporation Limited, Chengdu 610051, China
1 shared publication - Bin Yuan
School of Petroleum Engineering, China University of Petroleum (East China), Qingdao 266580, P. R. China
1 shared publication - Cheng Luo
Jidong Oilfield Company, Petrochina
1 shared publication
Latest Publications
- Open Access
Numerical Simulation of Hydraulic Fracture Propagation on Multilayered Formation Using Limited Entry Fracturing Technique
Hydraulic fracturing is one of the most effective stimulation methods for unconsolidated sandstone reservoirs. However, the design of hydraulic fracturing must take into account the mechanical and stress properties of different geological formations between layers. In this paper, a three-dimensional coupled fluid-solid model using the finite element method is developed to investigate multiple vertical fractures at different depths along a vertical wellbore under different geological and geomechanical conditions. The finite element model does not require further refinement of any new cracks, requiring much smaller degrees of freedom and higher computational efficiency. In addition, new elements were used to account for local pressure drop due to perforation entry friction along the vertical wellbore. Numerical simulation results indicate that hydraulic fracture connections are observed from adjacent layers. Furthermore, the low stress contrast and high Young’s modulus between the layers increases the likelihood of multiple fracture connections. Higher fluid leakage rates increase the likelihood of fracture branching, but decrease the area of fracture coverage near the wellbore. Increasing fluid viscosity is effective in improving the area of fracture coverage near the wellbore. These findings are useful for the design of hydraulic fracturing in multi-layered formations in unconsolidated sandstone formations.
Open AccessNumerical Simulation of Hydraulic Fracture Propagation on Multilayered Formation Using Limited Entry Fracturing Technique
Hydraulic fracturing is one of the most effective stimulation methods for unconsolidated sandstone reservoirs. However, the design of hydraulic fracturing must take into account the mechanical and stress properties of different geological formations between layers. In this paper, a three-dimensional coupled fluid-solid model using the finite element method is developed to investigate multiple vertical fractures at different depths along a vertical wellbore under different geological and geomechanical conditions. The finite element model does not require further refinement of any new cracks, requiring much smaller degrees of freedom and higher computational efficiency. In addition, new elements were used to account for local pressure drop due to perforation entry friction along the vertical wellbore. Numerical simulation results indicate that hydraulic fracture connections are observed from adjacent layers. Furthermore, the low stress contrast and high Young’s modulus between the layers increases the likelihood of multiple fracture connections. Higher fluid leakage rates increase the likelihood of fracture branching, but decrease the area of fracture coverage near the wellbore. Increasing fluid viscosity is effective in improving the area of fracture coverage near the wellbore. These findings are useful for the design of hydraulic fracturing in multi-layered formations in unconsolidated sandstone formations.
- Open Access
A Study on the Plugging Effect of Different Plugging Agent Combinations during CO2 Flooding in Heterogeneous Reservoirs
Gas channeling control is key to improving CO2-flooding efficiency. A traditional plugging system has disadvantages, such as poor adaptability and stability, leading to the poor plugging effect of CO2 channeling in heterogeneous reservoirs and difficulty in controlling the subsequent CO2 injection pressure. To achieve a significant plugging effect and effectively control the subsequent CO2 injection pressure, a heterogeneous physical model of gas channeling in a horizontal well was established, and plugging experiments were conducted using four different combinations of plugging agents during CO2 flooding. Three evaluation parameters were defined, including the temperature field variation coefficient (TFVC), medium-permeability diversion rate (MPDR), and subsequent injection pressure coefficient (SIPC). The plugging effect of different combinations of plugging agents during CO2 flooding in heterogeneous reservoirs was analyzed. The results show that the plugging effect after using a combination of plugging agents was significantly better than after using a single plugging agent, and different plugging agent combinations had distinct characteristics. The strong–medium–weak (S-M-W) combination had the best MPDR for subsequent CO2 flooding, but the SIPC was the highest. The strong–weak–strong–weak (S-W-S-W) and weak–strong–weak–strong (W-S-W-S) combinations could effectively control the SIPC. These results indicate that plugging using the S-W-S-W and W-S-W-S combinations can achieve an effective plugging effect and reasonably control the subsequent CO2 injection pressure. This work provides a personalized design scheme for effective gas channeling control and maintenance of appropriate injection pressure during CO2 flooding in heterogeneous reservoirs.
Open AccessA Study on the Plugging Effect of Different Plugging Agent Combinations during CO2 Flooding in Heterogeneous Reservoirs
Gas channeling control is key to improving CO2-flooding efficiency. A traditional plugging system has disadvantages, such as poor adaptability and stability, leading to the poor plugging effect of CO2 channeling in heterogeneous reservoirs and difficulty in controlling the subsequent CO2 injection pressure. To achieve a significant plugging effect and effectively control the subsequent CO2 injection pressure, a heterogeneous physical model of gas channeling in a horizontal well was established, and plugging experiments were conducted using four different combinations of plugging agents during CO2 flooding. Three evaluation parameters were defined, including the temperature field variation coefficient (TFVC), medium-permeability diversion rate (MPDR), and subsequent injection pressure coefficient (SIPC). The plugging effect of different combinations of plugging agents during CO2 flooding in heterogeneous reservoirs was analyzed. The results show that the plugging effect after using a combination of plugging agents was significantly better than after using a single plugging agent, and different plugging agent combinations had distinct characteristics. The strong–medium–weak (S-M-W) combination had the best MPDR for subsequent CO2 flooding, but the SIPC was the highest. The strong–weak–strong–weak (S-W-S-W) and weak–strong–weak–strong (W-S-W-S) combinations could effectively control the SIPC. These results indicate that plugging using the S-W-S-W and W-S-W-S combinations can achieve an effective plugging effect and reasonably control the subsequent CO2 injection pressure. This work provides a personalized design scheme for effective gas channeling control and maintenance of appropriate injection pressure during CO2 flooding in heterogeneous reservoirs.
- Open Access
Effect of Polymer and Crosslinker Concentration on Static and Dynamic Gelation Behavior of Phenolic Resin Hydrogel
The application results of profile control and water plugging technology are highly related to the gelation time and strength of phenolic resin hydrogel. In this work, a hydrogel solution was prepared by fully mixing the prepared polymer solution with a crosslinker. The static gelation process of PFR hydrogel in ampoule bottles and porous media was analyzed by changes in the viscosity and residual resistance coefficient. Then, the dynamic gelation of the PFR hydrogel in porous media was tested using a circulating flow device, and the changes in viscosity and injection pressure were analyzed during the dynamic gelation process. Finally, the effects of the polymer concentration and crosslinker concentration on dynamic gelation were analyzed. The initial gelation time and final gelation time in porous media were 1–1.5 times and 1.5–2 times those in ampoule bottles under static conditions, respectively. The initial dynamic gelation time in porous media was 2–2.5 times and 1.5–2 times the initial static gelation times in ampoule bottles and porous media, respectively. The final dynamic gelation time was four times and two times the initial static gelation times in ampoule bottles and porous media, respectively. The production after dynamic gelation in porous media comprised hydrogel aggregates and water fluid, leading to a high injection pressure and low viscosity of the produced liquid. As the concentration of polymer and crosslinker increased, the dynamic gelation time was shortened and the gel strength was increased. In the dynamic gelation process in porous media, the phenol resin hydrogel could migrate deeply, but it was limited by the concentrations of the polymer and crosslinker. The results of subsequent water flooding showed that the polymer hydrogel had a good plugging ability after dynamic gelation. The deep reservoir could only be blocked off in the subsequent water flooding process when the migration of hydrogel happened in the dynamic gelation process.
Open AccessEffect of Polymer and Crosslinker Concentration on Static and Dynamic Gelation Behavior of Phenolic Resin Hydrogel
The application results of profile control and water plugging technology are highly related to the gelation time and strength of phenolic resin hydrogel. In this work, a hydrogel solution was prepared by fully mixing the prepared polymer solution with a crosslinker. The static gelation process of PFR hydrogel in ampoule bottles and porous media was analyzed by changes in the viscosity and residual resistance coefficient. Then, the dynamic gelation of the PFR hydrogel in porous media was tested using a circulating flow device, and the changes in viscosity and injection pressure were analyzed during the dynamic gelation process. Finally, the effects of the polymer concentration and crosslinker concentration on dynamic gelation were analyzed. The initial gelation time and final gelation time in porous media were 1–1.5 times and 1.5–2 times those in ampoule bottles under static conditions, respectively. The initial dynamic gelation time in porous media was 2–2.5 times and 1.5–2 times the initial static gelation times in ampoule bottles and porous media, respectively. The final dynamic gelation time was four times and two times the initial static gelation times in ampoule bottles and porous media, respectively. The production after dynamic gelation in porous media comprised hydrogel aggregates and water fluid, leading to a high injection pressure and low viscosity of the produced liquid. As the concentration of polymer and crosslinker increased, the dynamic gelation time was shortened and the gel strength was increased. In the dynamic gelation process in porous media, the phenol resin hydrogel could migrate deeply, but it was limited by the concentrations of the polymer and crosslinker. The results of subsequent water flooding showed that the polymer hydrogel had a good plugging ability after dynamic gelation. The deep reservoir could only be blocked off in the subsequent water flooding process when the migration of hydrogel happened in the dynamic gelation process.
- 13 March 2023
- Published by Springer Nature in Chemical Papers
- Vol. 77 (7) , 3561-3570
The new low viscosity and high-temperature resistant composite hydrogel
- 13 March 2023
- Published by Springer Nature in Chemical Papers
- Vol. 77 (7) , 3561-3570
The new low viscosity and high-temperature resistant composite hydrogel
- 13 November 2020
- Published by Springer Nature in Chemical Papers
- Vol. 75 (4) , 1313-1322
Dynamic gelation of the HPAM/phenol–formaldehyde resin gel under oscillatory shear: critical gelation shear rate and reformation
- 13 November 2020
- Published by Springer Nature in Chemical Papers
- Vol. 75 (4) , 1313-1322
Dynamic gelation of the HPAM/phenol–formaldehyde resin gel under oscillatory shear: critical gelation shear rate and reformation