BCBin Chen

Bin Chen

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Bin Chen has a total of 19 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Multifractal Characteristics of Gain Structures: A Universal Law of Polycrystalline Strain-Hardening Behaviors

    by Maoqing Fu, Jiapeng Chen, Zhaowen Huang, Bin Chen, Yangfan Hu, Biao Wang

    The quantitative relationship between material microstructures, such as grain distributions, and the nonlinear strain-hardening behaviors of polycrystalline metals has not yet been completely understood. This study finds that the grain correlation dimension of polycrystals D is universally equal to the reciprocal of the strain-hardening exponent by experimental research and fractal geometry analysis. From a geometric perspective, the correlation dimension of grains is consistent with that of the equivalent plastic strain field, which represents the correlation dimension of the material manifold. According to the definition of the Hausdorff measure and Ludwik constitutive model, the strain-hardening exponent represents the exponent derived from the Dth root of the measure relationship. This universal law indicates that the strain-hardening behaviors are fractal geometrized and that the strain-hardening exponent represents a geometrical parameter reflecting the multifractal characteristics of grain structures. This conclusion can enhance the comprehension of the relationship between microstructure and mechanical properties of materials and highlights the importance of designing materials with non-uniform grain distributions to achieve desired hardening properties.


  • Open Access

    Calculation Based on the Formation of Mg2Si and Its Effect on the Microstructure and Properties of Al–Si Alloys

    by Jianfei Hao, Baoyi Yu, Jiancong Bian, Bin Chen, Huishu Wu, Weirong Li, Yanfang Li, Runxia Li

    In order to investigate the effect of Mg2Si formation on the microstructure and properties of an Al−Si alloy, the critical point of a hypereutectic Al−17Si−4Cu−Mg alloy was calculated by Pandat software. The calculation results of the equilibrium phase diagram show that the critical point for Mg2Si phase formation for the alloy was obtained when the Mg content was 2.2%. The contents of 0.5 wt.% Mg and 2.5 wt.% Mg were selected as the research object. The content of Mg increased from 0.5 wt.% to 2.5 wt.%, the eutectic Si in the matrix was reduced, and the Chinese character-like Mg2Si phase appeared in the microstructure. In the peak ageing state, in addition to θ″ and Q′ phases that were mainly precipitated, there was also needle-like β″ precipitation in the 2.5 wt.% Mg content alloy. Larger precipitates were found in 2.5 wt.% content alloys, mainly due to the promotion of the solid solution having the aggregation and segregation of more solute elements in the matrix. The tensile strength, elongation, and hardness of hypereutectic Al−17Si−4Cu−0.5Mg alloy under peak ageing were 331 MPa, 3.11%, and 152.1 HB, respectively. The tensile strength and the elongation decreased while the hardness increased with the 2.5 wt.% Mg content, which is due to the formation of hard and brittle Mg2Si and Al8FeMg3Si, which has a splitting effect on the matrix.


  • Open Access

    Synthesis of Cryolite (Na3AlF6) from Secondary Aluminum Dross Generated in the Aluminum Recycling Process

    by Bingbing Wan, Wenfang Li, Wanting Sun, Fangfang Liu, Bin Chen, Shiyao Xu, Weiping Chen, Aihua Yi

    Secondary aluminum dross (SAD) is regarded as a solid waste of aluminum recycling process that creates serious environmental and health concerns. However, SAD can also be used as a good source of aluminum, so that utilizing the SAD for the production of valuable products is a promising approach of recycling such waste. In the present work, a novel eco-friendly three-step process was proposed for the synthesis of cryolite (Na3AlF6) from the SAD, and it consisted of (1) water-washing pretreatment of SAD, (2) extraction of Al component via pyro-hydrometallurgy, including low-temperature alkaline smelting, water leaching and purification of leachate in sequence, (3) precipitation of cryolite from the purified NaAlO2 solution using the carbonation method. By analysis of the parameter optimization for each procedure, it was found that the maximum hydrolysis efficiency of aluminum nitride (AlN) in the SAD was around 68.3% accompanied with an extraction efficiency of Al reaching 91.5%. On this basis, the cryolite of high quality was synthesized under the following optimal carbonation conditions: reaction temperature of 75 °C, NaAlO2 concentration of 0.11 mol/L, F/(6Al) molar ratio of 1.10, and 99.99% CO2 gas pressure, and flow rate of 0.2 MPa and 0.5 L/min respectively. The formation of Na3AlF6 phase can be detected by XRD. The morphological feature observed by SEM revealed that the as-synthesized cryolite had a polyhedral shape (~1 μm size) with obvious agglomeration. The chemical composition and ignition loss of the as-synthesized cryolite complied well with the requirements of the Chinese national standard (GB/T 4291-2017).