Lixia Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Lixia Wang has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
Li Qian
National Engineering Research Center of Advance Polymer Processing Technology, Zhengzhou University , Zhengzhou City, Henan Province, P.R. China
2 shared publicationsChangyu Shen
National Engineering Research Center of Advance Polymer Processing Technology, Zhengzhou University , Zhengzhou City, Henan Province, P.R. China
1 shared publication- Jing Ma
Zhengzhou Univ, Coll Mech & Safety Engn, Natl Ctr Int Res Micronano Molding Technol, Zhengzhou 450001, Henan, Peoples R China
1 shared publication Luhan Kang
Zhengzhou Univ, Coll Mech & Safety Engn, Zhengzhou 450001, Henan, Peoples R China
1 shared publication- Mingfu Zhu
Henan Province Engineering Technology Research Center of MEMS Manufacturing and Applications, School of Mechanics and Safety Engineering Zhengzhou University Zhengzhou China
1 shared publication Shen Changyu
National Engineering Research Center for Advanced Polymer Processing Technology, Zhengzhou University, Postbox 148, No. 97 Wenhua Road, Zhengzhou 450002, P.R. China
1 shared publication
Latest Publications
- 30 October 2024
- Published by Elsevier in Materials Today Communications
- Vol. 41
Highly sensitive and stretchable CB/GNPs-TPU strain sensor with porous microstructure for multifunctional strain sensing
- 30 October 2024
- Published by Elsevier in Materials Today Communications
- Vol. 41
Highly sensitive and stretchable CB/GNPs-TPU strain sensor with porous microstructure for multifunctional strain sensing
- 8 March 2007
- Published by Taylor & Francis in Polymer-Plastics Technology and Engineering
- Vol. 46 (3) , 219-225
Investigation of the Effect of Molding Variables on Sink Marks of Plastic Injection Molded Parts Using Taguchi DOE Technique
The quality of an injection molded part is affected by material properties, mold geometry, process conditions etc. Obtaining optimum process conditions and mold design is the key problem to improve the part quality. Sink mark is one of several important flaws of injection molded parts. In this article, numerical simulation is combined with Taguchi design-of-experiment (DOE) technique to investigate the influence of process conditions and cavity geometry on sink mark of the injection molded part and optimize process conditions and cavity geometry. An L18(37) orthogonal array based on the Taguchi method was conducted to minimize the sink marks of injection molded parts, and the significance of each factors on sink mark was investigated. For the factors selected in the main experiments, part thickness, holding pressure, melt temperature and mold temperature were found to be the principal factors affecting the sink marks of the injection molded parts.
- 8 March 2007
- Published by Taylor & Francis in Polymer-Plastics Technology and Engineering
- Vol. 46 (3) , 219-225
Investigation of the Effect of Molding Variables on Sink Marks of Plastic Injection Molded Parts Using Taguchi DOE Technique
The quality of an injection molded part is affected by material properties, mold geometry, process conditions etc. Obtaining optimum process conditions and mold design is the key problem to improve the part quality. Sink mark is one of several important flaws of injection molded parts. In this article, numerical simulation is combined with Taguchi design-of-experiment (DOE) technique to investigate the influence of process conditions and cavity geometry on sink mark of the injection molded part and optimize process conditions and cavity geometry. An L18(37) orthogonal array based on the Taguchi method was conducted to minimize the sink marks of injection molded parts, and the significance of each factors on sink mark was investigated. For the factors selected in the main experiments, part thickness, holding pressure, melt temperature and mold temperature were found to be the principal factors affecting the sink marks of the injection molded parts.
- 1 March 2007
- Published by SAGE Publications in Journal of Reinforced Plastics and Composites
- Vol. 26 (4) , 353-372
Numerical Simulation of Compressible Flow with Phase Change of Filling Stage in Injection Molding
The filling stage in injection molding has important effects on the final properties and quality of the parts. It is significant to predict the history of flow and heat transfer in the filling stage accurately and thus predict the part properties and quality. The modeling is based on the generalized Hele–Shaw flow of a compressible viscous fluid under non-isothermal conditions with consideration of the effects of compressibility and phase change. A hybrid FEM/FDM method combined with a control volume method was adopted to simulate the filling stage in plastics injection molding. A program was developed and compressible flow analysis of the filling stage was implemented using Visual C++. Comparison of numerical and experimental results verified the numerical algorithm and program of the compressible filling simulation. The numerical analysis also indicated that the compressibility of the material had important effects on flow field of imbalance molds.
- 1 March 2007
- Published by SAGE Publications in Journal of Reinforced Plastics and Composites
- Vol. 26 (4) , 353-372
Numerical Simulation of Compressible Flow with Phase Change of Filling Stage in Injection Molding
The filling stage in injection molding has important effects on the final properties and quality of the parts. It is significant to predict the history of flow and heat transfer in the filling stage accurately and thus predict the part properties and quality. The modeling is based on the generalized Hele–Shaw flow of a compressible viscous fluid under non-isothermal conditions with consideration of the effects of compressibility and phase change. A hybrid FEM/FDM method combined with a control volume method was adopted to simulate the filling stage in plastics injection molding. A program was developed and compressible flow analysis of the filling stage was implemented using Visual C++. Comparison of numerical and experimental results verified the numerical algorithm and program of the compressible filling simulation. The numerical analysis also indicated that the compressibility of the material had important effects on flow field of imbalance molds.