Feipeng Xiao
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Feipeng Xiao has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Serji N. Amirkhanian
Department of Civil Construction and Environmental Engineering, University of Alabama, Tuscaloosa, AL 35487, USA
18 shared publications Wenbin Zhao
Department of Civil Engineering , Clemson University , Clemson , SC , 29634-0911 , USA
4 shared publicationsRengen Zhang
Senior Engineer, Zhejiang Provincial Planning Design & Research Institute of Communications, Huangzhou, China
3 shared publications- Armen N. Amirkhanian
Assistant Professor, Dept. of Civil, Construction, and Environmental Engineering, Univ. of Alabama, 3043 HM Comer, Tuscaloosa, AL 35487. ORCID:
2 shared publications Bradley Putman
Research Assistant Professor, Dept. of Civil Engineering, Clemson Univ., Clemson, SC 29634-0911
2 shared publications- Junan Shen
Department of Civil Engineering and Construction, Georgia Southern University, Statesboro, GA 30458, USA
2 shared publications
Latest Publications
- 1 October 2012
- Published by Taylor & Francis in International Journal of Pavement Engineering
- Vol. 13 (5) , 401-414
Laboratory investigation of moisture susceptibility of long-term saturated warm mix asphalt mixtures
Moisture damage in flexible pavements might cause stripping in asphalt pavements and ultimately result in premature failure. Warm mix asphalt (WMA) technology as a means to decrease the energy consumption and emissions associated with conventional hot mix asphalt production is broadly being used recently. However, the utilisation of the hydrated lime and liquid anti-strip additives in WMA mixtures makes these issues more complicated. The objective of this study was to investigate and evaluate the moisture susceptibility of mixtures containing anti-stripping agents (ASAs) and WMA additives after long-term saturated durations. The experimental design for this study included the utilisations of one binder source (PG 64-22), three ASA additives and control, two WMA additives and hot mix, and three aggregate sources. A total of 36 types of mixtures and 540 specimens were fabricated and tested in this study. The performed properties included indirect tensile strength (ITS), tensile strength ratio, flow and toughness. The results indicated that the aggregate source has an effect on dry ITS and flow values but had no effect on wet ITS, wet flow and toughness values. In addition, hot mixture generally had higher dry and wet ITS values, and there were significant differences in flow and toughness values between hot and warm mixtures. Moreover, the hydrated lime exhibited the best moisture resistance in WMA mixtures; the liquid ASA additives could increase the ITS values of mixtures but exhibited a weak moisture resistance in this study. Furthermore, the storage and saturated duration generally had no effect on ITS values, and statistical analysis results did not show any differences among these mixtures.
- 1 October 2012
- Published by Taylor & Francis in International Journal of Pavement Engineering
- Vol. 13 (5) , 401-414
Laboratory investigation of moisture susceptibility of long-term saturated warm mix asphalt mixtures
Moisture damage in flexible pavements might cause stripping in asphalt pavements and ultimately result in premature failure. Warm mix asphalt (WMA) technology as a means to decrease the energy consumption and emissions associated with conventional hot mix asphalt production is broadly being used recently. However, the utilisation of the hydrated lime and liquid anti-strip additives in WMA mixtures makes these issues more complicated. The objective of this study was to investigate and evaluate the moisture susceptibility of mixtures containing anti-stripping agents (ASAs) and WMA additives after long-term saturated durations. The experimental design for this study included the utilisations of one binder source (PG 64-22), three ASA additives and control, two WMA additives and hot mix, and three aggregate sources. A total of 36 types of mixtures and 540 specimens were fabricated and tested in this study. The performed properties included indirect tensile strength (ITS), tensile strength ratio, flow and toughness. The results indicated that the aggregate source has an effect on dry ITS and flow values but had no effect on wet ITS, wet flow and toughness values. In addition, hot mixture generally had higher dry and wet ITS values, and there were significant differences in flow and toughness values between hot and warm mixtures. Moreover, the hydrated lime exhibited the best moisture resistance in WMA mixtures; the liquid ASA additives could increase the ITS values of mixtures but exhibited a weak moisture resistance in this study. Furthermore, the storage and saturated duration generally had no effect on ITS values, and statistical analysis results did not show any differences among these mixtures.
- 1 April 2012
- Published by American Society of Civil Engineers (ASCE) in Journal of Performance of Constructed Facilities
- Vol. 26 (2) , 145-152
Influence of Short-Term Aging on Rheological Characteristics of Non-Foaming WMA Binders
The objective of this study was to conduct a laboratory investigation of rheological properties of non-foaming warm mix asphalt (WMA) binder after a short-term aging procedure. The conventional testing procedures such as viscosity, performance grade, creep and creep recovery, amplitude sweep, and frequency sweep were performed to determine the influences of non-foaming additives on asphalt binders. The experimental design included four binders and four non-foaming WMA additives. The test results indicated that, as expected, the non-foaming WMA additive can reduce the viscosity value of asphalt binder and thus decrease the mixing and compaction temperatures of the mixture. The failure temperatures of unaged and rolling thin film oven (RTFO) binders containing non-foam additives have a slight increase compared with the virgin binder, therefore improving the rut resistance of the mixtures. In addition, the creep recovery, amplitude, and frequency sweep tests show that the unaged and RTFO binders with...
- 1 April 2012
- Published by American Society of Civil Engineers (ASCE) in Journal of Performance of Constructed Facilities
- Vol. 26 (2) , 145-152
Influence of Short-Term Aging on Rheological Characteristics of Non-Foaming WMA Binders
The objective of this study was to conduct a laboratory investigation of rheological properties of non-foaming warm mix asphalt (WMA) binder after a short-term aging procedure. The conventional testing procedures such as viscosity, performance grade, creep and creep recovery, amplitude sweep, and frequency sweep were performed to determine the influences of non-foaming additives on asphalt binders. The experimental design included four binders and four non-foaming WMA additives. The test results indicated that, as expected, the non-foaming WMA additive can reduce the viscosity value of asphalt binder and thus decrease the mixing and compaction temperatures of the mixture. The failure temperatures of unaged and rolling thin film oven (RTFO) binders containing non-foam additives have a slight increase compared with the virgin binder, therefore improving the rut resistance of the mixtures. In addition, the creep recovery, amplitude, and frequency sweep tests show that the unaged and RTFO binders with...
- 1 January 2012
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 24 (1) , 48-56
Low-Volume Road WMA Mixtures: Moisture Susceptibility of Mixtures Containing Coal Ash and Roofing Shingle with Moist Aggregate
The objective of this study was to evaluate the laboratory moisture susceptibility of low-volume hot mix asphalt (HMA) and warm mix asphalt (WMA) mixtures containing moist aggregates and recycled materials, such as manufactured roofing shingles and coal ash material. These materials were tested after short- and long-term aging procedures. The test properties of these mixtures included indirect tensile strength (ITS), the tensile strength ratio (TSR), and the flow value of virgin and aged specimens. The experimental design included two percentages of coal ash (10 and 5% by weight of the aggregate), two roofing shingle contents (5 and 3% by weight of the aggregate), three WMA additives (Asphamin, Sasobit, and Evotherm), two antistripping agents (hydrated lime and one liquid antistripping agent), and two aggregate sources. A total of 72 mixtures were designed and a total of 416 ITS specimens were tested for short- and long-term aged procedures in this study. The test results indicated that the dry and wet IT...
- 1 January 2012
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 24 (1) , 48-56
Low-Volume Road WMA Mixtures: Moisture Susceptibility of Mixtures Containing Coal Ash and Roofing Shingle with Moist Aggregate
The objective of this study was to evaluate the laboratory moisture susceptibility of low-volume hot mix asphalt (HMA) and warm mix asphalt (WMA) mixtures containing moist aggregates and recycled materials, such as manufactured roofing shingles and coal ash material. These materials were tested after short- and long-term aging procedures. The test properties of these mixtures included indirect tensile strength (ITS), the tensile strength ratio (TSR), and the flow value of virgin and aged specimens. The experimental design included two percentages of coal ash (10 and 5% by weight of the aggregate), two roofing shingle contents (5 and 3% by weight of the aggregate), three WMA additives (Asphamin, Sasobit, and Evotherm), two antistripping agents (hydrated lime and one liquid antistripping agent), and two aggregate sources. A total of 72 mixtures were designed and a total of 416 ITS specimens were tested for short- and long-term aged procedures in this study. The test results indicated that the dry and wet IT...
- 1 November 2011
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 23 (11) , 1552-1559
Moisture Susceptibility of Warm-Mix Asphalt Mixtures Containing Nanosized Hydrated Lime
This research investigated the size effect of hydrated lime on the moisture susceptibility of warm-mix-asphalt (WMA) mixtures with selected additives. A superfine hydrated lime used in the study was produced from regular hydrated lime (RHL) by a Los Angeles abrasion machine. The superfine lime was measured to be 660 nm, approximately half of the RHL size of 1.3 µm, a sub-nano-sized hydrated lime (SNHL). Scanning electron microscope (SEM) pictures were taken to observe the difference of the crushed lime in size, shape, and texture. Experiments for antistripping properties, such as indirect tensile strength (ITS), tensile strength ratio (TSR), flow, and toughness were conducted on WMA mixtures containing SNHL and RHL as control samples. A total of 18 mixtures and 108 specimens were prepared from three types of aggregate, three WMA additives, and two types of lime. The results indicated that the microstructures of the SNHL and RHL are irregular: the lime particles have fractured and rough surfaces with sharp...
- 1 November 2011
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 23 (11) , 1552-1559
Moisture Susceptibility of Warm-Mix Asphalt Mixtures Containing Nanosized Hydrated Lime
This research investigated the size effect of hydrated lime on the moisture susceptibility of warm-mix-asphalt (WMA) mixtures with selected additives. A superfine hydrated lime used in the study was produced from regular hydrated lime (RHL) by a Los Angeles abrasion machine. The superfine lime was measured to be 660 nm, approximately half of the RHL size of 1.3 µm, a sub-nano-sized hydrated lime (SNHL). Scanning electron microscope (SEM) pictures were taken to observe the difference of the crushed lime in size, shape, and texture. Experiments for antistripping properties, such as indirect tensile strength (ITS), tensile strength ratio (TSR), flow, and toughness were conducted on WMA mixtures containing SNHL and RHL as control samples. A total of 18 mixtures and 108 specimens were prepared from three types of aggregate, three WMA additives, and two types of lime. The results indicated that the microstructures of the SNHL and RHL are irregular: the lime particles have fractured and rough surfaces with sharp...
- 1 October 2011
- Published by Taylor & Francis in International Journal of Pavement Engineering
- Vol. 12 (5) , 485-495
Viscosity prediction of CRM binders using artificial neural network approach
The primary objective of this study was to develop a series of artificial neural network (ANN) models to predict the viscosity values of crumb rubber-modified (CRM) binders using four input variables: asphalt binder source, rubber size, mixing duration and rubber content. The results indicated that ANN-based models are effective in predicting the viscosity values of CRM binders regardless of rubber type and can easily be implemented in a spreadsheet. In addition, the developed ANN model can be used to predict viscosity values of other types of CRM binders. Furthermore, the results also show that asphalt binder source, rubber size and rubber content are the most important factors in the developed ANN models while the mixing duration is relatively unimportant. The sensitivity analysis of input variables indicated that the viscosity changes significantly with changes in asphalt binder source, rubber size and rubber content.
- 1 October 2011
- Published by Taylor & Francis in International Journal of Pavement Engineering
- Vol. 12 (5) , 485-495
Viscosity prediction of CRM binders using artificial neural network approach
The primary objective of this study was to develop a series of artificial neural network (ANN) models to predict the viscosity values of crumb rubber-modified (CRM) binders using four input variables: asphalt binder source, rubber size, mixing duration and rubber content. The results indicated that ANN-based models are effective in predicting the viscosity values of CRM binders regardless of rubber type and can easily be implemented in a spreadsheet. In addition, the developed ANN model can be used to predict viscosity values of other types of CRM binders. Furthermore, the results also show that asphalt binder source, rubber size and rubber content are the most important factors in the developed ANN models while the mixing duration is relatively unimportant. The sensitivity analysis of input variables indicated that the viscosity changes significantly with changes in asphalt binder source, rubber size and rubber content.
- 1 September 2011
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 23 (9) , 1328-1337
Utilization of Foaming Technology in Warm-Mix-Asphalt Mixtures Containing Moist Aggregates
The objective of this study was to conduct a laboratory investigation of moisture susceptibility and rutting resistance of warm-mix asphalt (WMA) mixtures containing moist aggregates by using a foaming technology. Gyration number of various samples, indirect tensile strength (ITS), tensile strength ratio, rut depths of dry and conditioned specimens, and deformation (flow) were measured for all mixtures. The experimental design included two aggregate moisture contents (0 and ∼0.5% by weight of the dry mass of the aggregate), two lime contents (1% and 2% lime by weight of dry aggregate), one liquid antistripping agent (ASA) and non-ASA, three foaming water contents (2, 3, and 4%) with control, and two aggregate sources. A total of 42 mixtures were used and 420 specimens were tested in this study. The test results indicated that the aggregate source significantly affects the ITS and rutting resistance regardless of the foaming water content, ASA, and aggregate moisture content. In addition, the ITS and rut d...
- 1 September 2011
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 23 (9) , 1328-1337
Utilization of Foaming Technology in Warm-Mix-Asphalt Mixtures Containing Moist Aggregates
The objective of this study was to conduct a laboratory investigation of moisture susceptibility and rutting resistance of warm-mix asphalt (WMA) mixtures containing moist aggregates by using a foaming technology. Gyration number of various samples, indirect tensile strength (ITS), tensile strength ratio, rut depths of dry and conditioned specimens, and deformation (flow) were measured for all mixtures. The experimental design included two aggregate moisture contents (0 and ∼0.5% by weight of the dry mass of the aggregate), two lime contents (1% and 2% lime by weight of dry aggregate), one liquid antistripping agent (ASA) and non-ASA, three foaming water contents (2, 3, and 4%) with control, and two aggregate sources. A total of 42 mixtures were used and 420 specimens were tested in this study. The test results indicated that the aggregate source significantly affects the ITS and rutting resistance regardless of the foaming water content, ASA, and aggregate moisture content. In addition, the ITS and rut d...
- 29 June 2011
- Published by Springer Nature in Materials and Structures
- Vol. 45 (1-2) , 251-264
Effects of long-term aging on moisture sensitivity of foamed WMA mixtures containing moist aggregates
- 29 June 2011
- Published by Springer Nature in Materials and Structures
- Vol. 45 (1-2) , 251-264
Effects of long-term aging on moisture sensitivity of foamed WMA mixtures containing moist aggregates
- 16 May 2011
- Published by American Society of Civil Engineers (ASCE)
- p. 1-8
Rheological Investigation of Non-Foaming WMA Additives at Mid-Temperature
In this study, the objective was to conduct a laboratory investigation of rheological properties of non-foaming WMA additives at a mid-temperature. The conventional testing procedures such as viscosity, performance grade, creep and creep recovery, and frequency sweep were performed to determine the influences of non-foaming additives on asphalt binders. The experimental design included four binders and four non-foaming WMA additives. The test results indicated that, as expected, the non-foaming WMA additive can reduce the viscosity value of asphalt binder and thus decrease the mixing and compaction temperatures of mixture. The failure temperature of binders containing non-foam additive has a slight increase compared to the virgin binder and thus, improve the rut resistance of the mixtures. In addition, creep recovery and frequency sweep tests show that the binder with Sasobit has a slightly higher complex modulus but exhibits lower creep compliance and phase angle than the binder containing other WMA additives.
- 16 May 2011
- Published by American Society of Civil Engineers (ASCE)
- p. 1-8
Rheological Investigation of Non-Foaming WMA Additives at Mid-Temperature
In this study, the objective was to conduct a laboratory investigation of rheological properties of non-foaming WMA additives at a mid-temperature. The conventional testing procedures such as viscosity, performance grade, creep and creep recovery, and frequency sweep were performed to determine the influences of non-foaming additives on asphalt binders. The experimental design included four binders and four non-foaming WMA additives. The test results indicated that, as expected, the non-foaming WMA additive can reduce the viscosity value of asphalt binder and thus decrease the mixing and compaction temperatures of mixture. The failure temperature of binders containing non-foam additive has a slight increase compared to the virgin binder and thus, improve the rut resistance of the mixtures. In addition, creep recovery and frequency sweep tests show that the binder with Sasobit has a slightly higher complex modulus but exhibits lower creep compliance and phase angle than the binder containing other WMA additives.
- 4 April 2011
- Published by Taylor & Francis in International Journal of Pavement Engineering
- Vol. 12 (6) , 533-541
Long-term ageing influence on rheological characteristics of asphalt binders containing carbon nanoparticles
Nano-sized particles have been used in numerous applications to improve properties of various materials. The utilisation of nanotechnology in civil engineering area is relatively new and its use and applications are expected to increase rapidly. The objective of this study was to investigate and evaluate the rheological properties of binders containing various percentages of carbon nanoparticles after a long-term ageing process. The experimental design for this study included the utilisations of five binder sources (three grades of PG 64-22, PG 64-16 and PG 52-28) and four nano percentages (0.0, 0.5, 1.0 and 1.5% by weight of the virgin binder). The rheological characteristics of these pressurised aged vessel (PAV) binders were tested including G* value, creep and creep recovery, and frequency and amplitude sweep at an intermediate temperature and deflection, stiffness and m-value at a low temperature as well. The results of the experiments indicated that the addition of nanoparticles does not increase the G* values and does have an obvious effect on complex modulus, phase angle under a frequency sweep test. However, nanoparticles have a slight effect on creep angle and compliance of a binder. Moreover, at a low tested temperature, the experimental results indicate that the nanoparticles have no effect on deflection, stiffness and m-value of PAV residue. Furthermore, statistical analysis indicates that the asphalt binder source and grade rather than nanoparticles play a key role in determining the rheological properties
- 4 April 2011
- Published by Taylor & Francis in International Journal of Pavement Engineering
- Vol. 12 (6) , 533-541
Long-term ageing influence on rheological characteristics of asphalt binders containing carbon nanoparticles
Nano-sized particles have been used in numerous applications to improve properties of various materials. The utilisation of nanotechnology in civil engineering area is relatively new and its use and applications are expected to increase rapidly. The objective of this study was to investigate and evaluate the rheological properties of binders containing various percentages of carbon nanoparticles after a long-term ageing process. The experimental design for this study included the utilisations of five binder sources (three grades of PG 64-22, PG 64-16 and PG 52-28) and four nano percentages (0.0, 0.5, 1.0 and 1.5% by weight of the virgin binder). The rheological characteristics of these pressurised aged vessel (PAV) binders were tested including G* value, creep and creep recovery, and frequency and amplitude sweep at an intermediate temperature and deflection, stiffness and m-value at a low temperature as well. The results of the experiments indicated that the addition of nanoparticles does not increase the G* values and does have an obvious effect on complex modulus, phase angle under a frequency sweep test. However, nanoparticles have a slight effect on creep angle and compliance of a binder. Moreover, at a low tested temperature, the experimental results indicate that the nanoparticles have no effect on deflection, stiffness and m-value of PAV residue. Furthermore, statistical analysis indicates that the asphalt binder source and grade rather than nanoparticles play a key role in determining the rheological properties
- 1 April 2011
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 23 (4) , 423-431
Influence of Carbon Nanoparticles on the Rheological Characteristics of Short-Term Aged Asphalt Binders
Nanotechnology has the potential to create many new materials and devices with wide-ranging purposes. Nano-sized particles have been used in numerous applications to improve the properties of various materials. The utilization of nanotechnology in civil engineering is expected to increase and may become an attractive alternative for asphalt binder modification. The objective of this study was to investigate and evaluate the rheological properties of binders containing various percentages of carbon nanoparticles after a short-term aging process. The experimental design for this study included five binder sources (three grades including PG 64-22, PG 64-16, and PG 52-28), three nano percentages (0.5, 1.0, and 1.5% by weight of the virgin binder), and control binders. The rheological characteristics of the rolling thin film oven (RTFO) binders, including failure temperature, performance grade, creep and creep recovery, viscous flow, and frequency and amplitude sweep, were tested. The results of the experiment...
- 1 April 2011
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 23 (4) , 423-431
Influence of Carbon Nanoparticles on the Rheological Characteristics of Short-Term Aged Asphalt Binders
Nanotechnology has the potential to create many new materials and devices with wide-ranging purposes. Nano-sized particles have been used in numerous applications to improve the properties of various materials. The utilization of nanotechnology in civil engineering is expected to increase and may become an attractive alternative for asphalt binder modification. The objective of this study was to investigate and evaluate the rheological properties of binders containing various percentages of carbon nanoparticles after a short-term aging process. The experimental design for this study included five binder sources (three grades including PG 64-22, PG 64-16, and PG 52-28), three nano percentages (0.5, 1.0, and 1.5% by weight of the virgin binder), and control binders. The rheological characteristics of the rolling thin film oven (RTFO) binders, including failure temperature, performance grade, creep and creep recovery, viscous flow, and frequency and amplitude sweep, were tested. The results of the experiment...