PBPeter Baltus

Peter Baltus

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Peter Baltus has a total of 41 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    A 23-GHz TX/LNA Front-End Module for Inter-Satellite Links With 27.8% Peak Efficiency in the TX Path and 3.1-dB NF in the RX Path

    by Kaijie Ding, Vojkan Vidojkovic, Dusan Milosevic, Khaled Khalaf, Rainier van Dommele, Mark Bentum, Peter Baltus

    This article presents a 23-GHz transmitter/low-noise amplifier (TX/LNA) front-end module (FEM) in 130-nm SiGe BiCMOS for inter-satellite links (ISLs) in the system of orbiting low-frequency antenna array (OLFAR). The FEM consists of an LNA, a power amplifier (PA), a variable-gain amplifier (VGA), a phase shifter (PS), and a TX/receiver switch (T/R SW). By applying the combination of different techniques: 1) multi-function block design strategy; 2) current reuse and ${\mathrm { g}}_{\mathrm { m}}$ boosting implemented by a triple-coil transformer in the LNA; 3) dual-LC-tank-based integrated T/R SW, a compact FEM is achieved, simultaneously with an advanced-state-of-the-art efficiency in the TX path and a competitive noise figure (NF) in the receiver (RX) path. In the TX path, it demonstrates a measured saturated output power ( $\mathrm {P}_{\mathrm {sat}}$ ) of 16.8 dBm, a peak TX efficiency of 27.8%, and a 34.1-dB gain. It supports 900-Mbps 64-QAM signals with 4.9% error vector magnitude (EVM) and −27.5-dBc adjacent channel power ratio (ACPR), at 9.0-dBm output power ( $\mathrm {P}_{\mathrm {out}}$ ) with 8.8% TX efficiency. In the RX path, an NF of 3.1 dB and an input 1-dB compression point (IP $_{\mathrm {1~dB}}$ ) of −19.4 dBm are achieved with a 19.3-dB gain and a 10-mW power consumption. The core chip area is $1.11\times 0.48$ mm.


  • A 0.32 nW–1.07 µW All-Dynamic Versatile Resistive Sensor Interface With System-Level Ratiometric Measurement

    by Haoming Xin, Peter Baltus, Eugenio Cantatore, Pieter Harpe

    An ultra-low power, energy efficient, and versatile resistive sensor interface for energy constrained internet-of-things applications is presented. The sensor interface includes an efficiently duty-cycled current digital-to-analog converter (I-DAC) and an asynchronous successive approximation register (SAR) analog-to-digital converter (ADC), which enables a fully-dynamic operation. A fast start-up circuit is used in the duty-cycled I-DAC to speed up the start-up procedure and to minimize the energy consumption. A system-level correlated double sampling (CDS) technique is employed to suppress ADC offset and 1/ $f$ noise. To tackle the limited robustness against supply and temperature variations observed in a previous implementation of the sensor interface, a system-level ratiometric measurement (SRM) approach is employed in an updated design, which is described here in detail. The chip is fabricated in 65nm CMOS technology. Thanks to the all-dynamic nature, measurement rates from 0.1S/s to 12.5kS/s can be supported with an inherent scaling of power over 3 orders of magnitude. A reported lowest power consumption of 0.32nW is achieved at 0.1S/s. Adaptable resolution with efficient scaling of power can also be achieved by adjusting sensor interface settings and/or using oversampling and averaging. The achieved figure-of-merit (FoM), which ranges from 98 to 552fJ/conv-step is also the lowest among prior designs. Thanks to the SRM approach, only 3.6%/V and 21ppm/ $^\circ \text{C}$ supply and temperature sensitivity are obtained, respectively.


  • A 1.25 μJ per Measurement Ultrasound Rangefinder System in 65 nm CMOS for Explorations With a Swarm of Sensor Nodes

    by Gonenc Berkol, Peter G. M. Baltus, Pieter J. A. Harpe, Eugenio Cantatore

    This paper presents an ultrasound rangefinder system able to find relative distances among energy-constrained sensor nodes. The nodes build a swarm that is operated in collision and multipath rich environments. A new distance measurement technique combining Wake-up and Frequency Modulated Continuous Wave (FMCW) is proposed to enable the ranging while neglecting the echoes from passive reflectors in the environment. The building blocks of the sensor nodes comprise a transmitter, a wake-up receiver, and a ranging receiver, all implemented in a 65 nm CMOS technology. The transmitter includes two switched-capacitor converters and an output multiplexer to generate a four-level driving signal and broadcast either a wake-up sequence or a digitally synthesized ultrasound Chirp. The transmitter dissipates 0.43 μJ and 0.82 μJ to broadcast the wake-up signal and the Chirp, respectively. A mixer first architecture is exploited in the wake-up receiver to reduce the always-on power consumption of the nodes. The ranging receiver uses a heterodyne architecture suited for the FMCW. The power consumption of the wake-up receiver and ranging receiver is 23.6 nW and 0.56 μW, respectively. The proposed rangefinder is experimentally characterized up to a 1 m distance in air and dissipates 1.25 μJ per measurement, achieving a resolution of 18.7 mm at 0.55 m.


  • A Compact Fully Dynamic Capacitance-to-Digital Converter With Energy-Efficient Charge Reuse

    by Haoming Xin, Kevin Pelzers, Peter Baltus, Eugenio Cantatore, Pieter Harpe

    An ultra-low power fully dynamic capacitance-to-digital converter (CDC) that exploits a novel charge reuse technique is proposed. The CDC includes a capacitive bridge as the sensing frontend and an asynchronous SAR ADC for signal digitization. Passive charge sharing between the frontend and ADC is used to enable a fully dynamic operation. Instead of resetting the capacitive bridge (with large sensing and reference capacitors) for each measurement, the charge is maintained and reused over many measurements to save energy. A power gating technique is employed to reduce the stand-by power. As a result, a FoM as low as 4.3fJ/conv-step is achieved for the CDC, which is >3x better than the state-of-the-art. Furthermore, it supports an inherent scaling of power vs. speed with a minimum power of only 44pW and a compact chip area of 6440μm.


  • Open Access

    Design Methodology for Industrial Internet-of-Things Wireless Systems

    by Carlos Mendes da Costa, Peter Baltus

    The ubiquity foreseen by the Internet-of-Things (IoT) and powered by the 5G advancements has motivated research on wireless solutions for critical applications, in particular, Industrial IoT (IIoT). Nevertheless, there is little or no research on a unified design methodology for IIoT that tackles the conflicting wireless system performances of Power, Latency, and Reliability (PLR). Obtaining such a framework is vital for empowering further development and fair comparison in future IIoT designs. Thereby, this paper presents a novel design methodology to tackle PLR trade-off in IIoT Wireless Systems (IIoT-WS). This new methodology uses a meet-in-the-middle system approach to design an entire PLR RF system, and a custom Multiple-Criteria Decision Analysis (MCDA) to help decide the best design variables that are both resource-efficient and PLR-balanced for a given application. Finally, to quantify the methodology for critical wireless systems, a lab-demonstrator for automotive application is designed and its performance compared to other wireless systems standards.


  • A 2.67 μJ per Measurement FMCW Ultrasound Rangefinder System for the Exploration of Enclosed Environments

    by Gonenc Berkol, Peter G. M. Baltus, Pieter J. A. Harpe, Eugenio Cantatore

    This paper presents the design and experimental characterization of an ultrasound rangefinder system. A new distance measurement method is proposed for determining the relative position among sensor nodes that are operated in a collision and multipath rich environment, while needing no common time reference between them. A 65nm CMOS technology has been used to build the sensor nodes, which comprise an on-chip receiver and transmitter. The proposed rangefinder system is characterized up to 1m in air and has a range resolution of 6.5mm, while dissipating 2.67μJ per measurement.


  • Open Access

    Distortion Contribution Analysis for Identifying EM Immunity Failures

    by Lammert Duipmans, Dusan Milosevic, Arnoud van der Wel, Peter Baltus

    One of the main causes of expensive IC redesigns is a failure to meet electromagnetic compatibility (EMC) requirements. For this reason, there is a huge demand for verification methods to identify and prevent immunity failures on chip. Strongly nonlinear effects, in particular DC operating point shifts, are a major cause of such immunity failures. Conventional analysis techniques, used to simulate these strongly nonlinear effects, suffer from a few drawbacks. They can be time-consuming and suffer from convergence issues. Moreover, they do not provide insight into the root causes of the nonlinear behavior. In this paper, an automated method is proposed that overcomes the mentioned drawbacks and identifies causes of immunity failures by listing critical distortion contributions. The method is applicable to very large, strongly nonlinear integrated circuits. It uses a simple model that determines the nonlinear contribution of one device in its linearized environment. Because the computation time is negligible, the analysis can be repeated for many devices and interference frequencies. Additionally, the method gives insight into the drivers responsible for the distortion effects, such that the designer can efficiently solve the problem. The method is demonstrated by applying it to a practical test case.


  • 60-GHz Low-Noise VGA and Interpolation-Based Gain Cell in a 40-nm CMOS Technology

    by Bindi Wang, Hao Gao, A. Rainier van Dommele, Marion K. Matters-Kammerer, Peter G. M. Baltus

    This paper presents the design and measurement of an interpolation-based low noise and variable gain cell (IBA-cell) in the 60-GHz band, using a 40-nm CMOS technology. The interpolation-based gain cell is designed for an innovative analog beamforming front end, where the array pattern is not only controlled in the phase domain, but also wins the flexibility in the magnitude domain. The circuit specifications are first derived for the application at 60 GHz. Techniques to combine low noise figure (NF) with variable gain tuning are presented focusing on the NF and linearity (IIP₃) on the example of a 60-GHz low noise amplifier and variable gain amplifier. Subsequently, the design and measurement of the whole gain cell (IBA-cell) integrated into a single chip are reported with the technique of a cross-coupled feedback loop to reduce the phase variations over the gain tuning states and enhance the variations of IIP₃. The IBA-cell achieves 15.8-dB maximum gain and 6.5-dB NF at 57 GHz with the gain tuning range from -2 to 15.8 dB and IIP₃ varying from -11.3 to -16 dBm over the gain control range. The IBA-cell consumes a dc power of maximum 54 mA from 1.1 V.


  • A 1.9 mW 250 MHz Bandwidth Continuous-Time ΣΔ Modulator for Ultra-Wideband Applications

    by M. Neofytou, M. Zhou, M. Bolatkale, Q. Liu, C. Zhang, G. Radulov, P. Baltus, L. Breems

    This paper proposes an architecture design approach for a wideband continuous-time (CT) ΣΔ modulator with ultra-low oversampling ratio (OSR). The ultra-low OSR is beneficial in terms of power consumption for both the clock distribution network and the subsequent decimation filter. In this work, three signal feedforward paths and an additional feedback path are used to reduce the power consumption. Extensive system-level simulations demonstrate the effectiveness of the proposed solutions. Furthermore, this work verifies the proposed methods by transistor-level design and simulations of a 2 GHz 4 th -order CT ΣΔ modulator achieving an SNDR of 46 dB in a signal band of 250 MHz while consuming only 1.91 mW of power in 40 nm CMOS. The proposed solutions enable CT ΣΔ modulators for low power ultra-wideband (UWB) applications.


  • Damper-to-damper path loss characterization for Intra-Vehicular Wireless Sensor Networks

    by Carlos A. M. Costa, Hao Gao, Thibault Le Polain, Rainier van Dommele, Bart Smolders, Miguel Dheans, Peter Baltus