Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Laurentiu Constantin Ceatra has a total of 24 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Experimental Investigation of Alcohol-Blended Aviation Fuels for Hybrid Power Sources in UAV Applications

    by Maria Căldărar, Tiberius-Florian Frigioescu, Mădălin Dombrovschi, Gabriel-Petre Badea, Laurențiu Ceatră, Flavia-Elena Blaga, Răzvan Roman

    The development of low-emission and reliable propulsion systems is essential for extending the operational capability of unmanned aerial vehicles (UAVs). Although aviation decarbonization is widely recognized as an important objective, it must be considered within the broader context of limited renewable-energy availability. Recent system-level analyses of transportation decarbonization have shown that the allocation of renewable electricity and sustainable fuels should prioritize sectors where direct electrification is most efficient, while hard-to-electrify sectors require alternative pathways. Aviation is one of the most difficult transport sectors to electrify because of strict energy-density requirements, especially for long-endurance airborne platforms. Therefore, sustainable liquid fuels and hybrid propulsion systems should not be considered universal replacements for electrification, but rather complementary solutions for applications where batteries alone cannot provide the required endurance, payload capacity or operational flexibility. In this context, the present study focuses on alcohol–kerosene blends for hybrid UAV power systems, where liquid-fuel energy density and partial emission reduction remain relevant engineering requirements. This work provides one of the first systematic experimental evaluations of ethanol–, butanol– and octanol–kerosene blends in a micro-turboprop engine operating as part of a hybrid UAV power-generation architecture. Unlike previous studies focused mainly on micro-turbojet thrust response, the present work evaluates the coupled influence of alcohol chain length and blending ratio on exhaust gas temperature, gaseous emissions, electrical output and operational stability under multi-load conditions representative of UAV operation. Jet-A and nine alcohol–kerosene blends containing 10%, 20% and 30% ethanol, butanol or octanol by volume were tested over four operating regimes, from idle to 2500 W electrical load. The results show that ethanol blends provided the strongest CO reduction, with E30 reducing CO by 24.9% relative to Jet-A under R3, while E10 offered the most balanced behavior across the full operating range. Higher ethanol fractions improved CO suppression but introduced NOx and low-load stability penalties. Octanol blends, particularly O20, exhibited the most kerosene-like and stable response, supporting reliable power delivery with reduced operational variability. Butanol blends showed intermediate behavior without providing a dominant advantage. A multi-criteria evaluation combining emissions, EGT behavior, relative performance, operational stability and cost identified E10 as the best overall compromise for hybrid UAV use. The study demonstrates that alcohol chain length produces nonlinear system-level effects in hybrid micro-turboprop architectures and provides an experimental basis for fuel selection in low-emission UAV power systems.


  • Open Access

    Influence of Butanol Additives on Combustion Performance and Emission Behavior in Micro-Turboprop Engines for UAV Applications

    by Maria Căldărar, Gabriel-Petre Badea, Mădălin Dombrovschi, Tiberius-Florian Frigioescu, Laurențiu Ceatră, Flavia-Elena Blaga, Răzvan Roman

    The transition toward sustainable aviation fuels for unmanned aerial vehicle propulsion requires alternative fuel blends that reduce emissions while maintaining stable power generation. This study investigates the combustion performance, electrical output, emission behavior, and near-field pollutant dispersion of butanol–kerosene blends in a hybrid micro-turboprop propulsion platform representative of UAV applications. Conventional kerosene and three butanol–kerosene blends, containing 10%, 20%, and 30% butanol by volume, were tested under four operating regimes ranging from idle to approximately 2.5 kW electrical load. Exhaust gas temperature, CO, NO, NOx, SO2, electrical power output, throttle response, and pollutant dispersion behavior were evaluated experimentally, while polynomial regression was applied to quantify throttle–power relationships. The results show that the 20% butanol blend provided the most favorable overall performance. Relative to conventional kerosene, B20 achieved approximately 4.8% higher electrical power output at equivalent throttle settings, reduced fuel demand by nearly 3.9%, and decreased the throttle requirement for 2 kW electrical output by almost 5%. In terms of emissions, B20 reduced CO formation across low and intermediate operating regimes while maintaining moderate NOx levels and stable exhaust gas temperature behavior. Increasing butanol content also improved plume homogenization: the anisotropy index decreased from 2.41 for B10 to 1.96 for B20 and 1.58 for B30, while high-concentration plume regions were reduced by up to 31%. However, B30 introduced stronger evaporative cooling, ignition delay effects, and reduced mid-load responsiveness. Overall, moderate butanol blending, particularly B20, represents the most balanced solution for reducing the environmental footprint of hybrid UAV micro-turboprop propulsion without significant performance penalties.


  • Open Access

    Experimental Assessment of Combustion Performance and Emission Characteristics of Ethanol–Jet A1 Blends in a Turboprop Engine for UAV Applications

    by Maria Căldărar, Mădălin Dombrovschi, Tiberius-Florian Frigioescu, Gabriel-Petre Badea, Laurentiu Ceatra, Răzvan Roman

    The increasing need to reduce reliance on fossil-derived aviation fuels and mitigate environmental impacts has intensified research into renewable alternatives for aviation energy systems. The growing interest in ethanol-based fuels is primarily driven by their simple oxygen-rich molecular structure and advantageous physicochemical characteristics, yet experimental studies examining their application in hybrid power architectures, including micro-turboprop engine-based power sources, are still limited. This study presents an experimental investigation of ethanol–Jet A1 fuel blends used in a micro-turboprop engine operating as a power generation unit for unmanned aerial vehicle applications. Ethanol was blended with Jet A1 at volumetric fractions of 10%, 20% and 30% and the engine was tested under multiple operating regimes corresponding to different electrical power outputs. Exhaust gas temperature, electrical power output and gaseous emissions (CO and NOx) were measured for each operating condition. The results indicate that low ethanol fractions (E10) provide performance comparable to neat kerosene, while higher ethanol fractions lead to a reduction in exhaust gas temperature at low-power regimes due to the lower heating value and high latent heat of vaporization of ethanol. Emission measurements showed a decrease in NOx emissions with increasing ethanol content, associated with lower combustion temperatures, while CO emissions increased at low-power regimes due to incomplete combustion under lean conditions. Additionally, combustion instability was observed during rapid transitions from maximum to idle regime operation for higher ethanol blends, attributed to transient ultra-lean mixtures, evaporative cooling, and reduced reaction rates. The results demonstrate that ethanol–kerosene blends can be used in micro-turboprop systems at low blend ratios without major performance penalties, but transient operating conditions impose stability limits that must be considered in practical UAV power system applications.


  • Open Access

    Physicochemical Properties of Jet-A/n-Heptane/Alcohol Blends for Turboengine Applications

    by Sibel Osman, Laurentiu Ceatra, Grigore Cican, Radu Mirea

    This work investigated the physical properties of Jet-A blended with n-heptane and various n-alcohols. The mixtures contained 10%, 20%, and 30% n-alcohols, including n-propanol, n-butanol, n-pentanol, n-hexanol, n-heptanol, and n-octanol. These alcohols are either derived from biomass or have significant potential for bio-based production. The blends were assessed against American Society for Testing and Materials (ASTM) D1655 standards for Jet-A in terms of the density, viscosity, and flash point. Additionally, the refractive index and Fourier Transform Infrared Spectroscopy (FTIR) analysis were employed to gain insights into the blend chemical composition. Density measurements for the blends fell within the ASTM specifications (0.7939 to 0.8075 g·cm−3). Viscosity measurements at −20 °C were not directly conducted due to technical limitations. However, extrapolating viscosity–temperature data suggests that the blends would meet the ASTM standard. Flash point measurements revealed that all mixtures exhibited values below the ASTM specification of 38 °C. Regression equations were developed to estimate the density, kinematic viscosity, and refractive index of the studied mixtures as a function of alcohol volume. Furthermore, a correlation study was conducted to estimate density and viscosity from refractive index measurements, given their simplicity, and minimal sample volume requirements. The R2 values for these correlations exceeded 0.99, indicating a strong relationship between the refractive index and the other properties.


  • Open Access

    Biodiesel from Recycled Sunflower and Palm Oil—A Sustainable Fuel for Microturbo-Engines Used in Airside Applications

    by Grigore Cican, Daniel Eugeniu Crunteanu, Radu Mirea, Laurentiu Constantin Ceatra, Constantin Leventiu

    An experimental assessment of burning behavior of some aviation fuel and biodiesel obtained from waste oil mixture has been performed within this paper. The biodiesel was obtained from sunflower and palm waste oil (SFP) and the mixtures consisted of 10, 30 and 50% biodiesel in regular aviation fuel. The aviation fuel is a mixture of Jet A fuel + 5% Aeroshell 500 oil (called Ke) with the oil being added for turbo-engine’s lubrication. So, the used fuels were: Ke, Ke + 10% SFP, Ke + 30% SFP, Ke + 50% SFP. In first step, SFP was characterized in terms of: density, kinematic viscosity, flash and freezing points and calorific power. Also a deeper analysis was made by using FTIR for all the fuels involved in the experiments. The second step consisted of assessing the chemical reactions that occur during the burning process. Thus starting from the known elemental analysis, the air needed for a stoichiometric reaction has been calculated for each fuel mixtures. Also the resulting CO2 and water has been calculated from the reactions. The third step consisted of experimental testing the burning behavior of the above mentioned fuels on a micro turbo-engine. The used engine was Jet Cat P80® provided by Gunt Hamburg, Barsbüttel, Germany. The variation of: rpm vs. time, burning temperature vs. time and fuel debit vs. rpm are presented for starting and yield procedures. The tests have been conducted at 8 different working regimes of the engine. For each regime, an 1 min testing period was chose, during which burning temperature vs. rpm, fuel debit vs. rpm and thrust force vs. rpm were monitored. For maximum regime, only calculus for burning, thermal efficiencies and specific consumption have been made. As a main conclusion, the engine working behavior was steady throughout the entire range of rpm and for all the blends fed, thus the studied fuel blends may be considered as sustainable fuel for applications that are using micro turbo-engines with main advantages related to pollution and raw materials allowing the production of this type of fuel.


  • Open Access

    Assessment of Hot Corrosion in Molten Na2SO4 and V2O5 of Inconel 625 Fabricated by Selective Laser Melting versus Conventional Technology

    by Teodor Adrian Badea, Dan Batalu, Nicolae Constantin, Alexandru Paraschiv, Delia Pătroi, Laurentiu Constantin Ceatra

    Inconel 625 samples, obtained by Selective Laser Melting (SLM) and conventional technology, were tested for hot corrosion resistance against a molten mixture of Na2SO4 and V2O5. The assessments were performed in air, at 900 °C with exposure time of up to 96 h, and at 1000 °C for 8 h. Weight gain was higher for samples obtained by SLM, with 37.4% after 8 h, 3.98% after 24 h, 4.46% after 48 h, and 5.8% after 96 h at 900 °C (22.6% at 1000 °C, 8 h). Three stages of corrosion were observed, the first and last with a high corrosion rate, while the second one showed a slower corrosion rate. Corrosion behaviour depends on the morphology of the grain boundary, which can influence the infiltration of corrosive salts, and on the formation of Cr2NiO4 compound, which acts as a temporary barrier.


  • Open Access

    In Vitro Physical-Chemical Behaviour Assessment of 3D-Printed CoCrMo Alloy for Orthopaedic Implants

    by Radu Mirea, Iuliana Manuela Biris, Laurentiu Constantin Ceatra, Razvan Ene, Alexandru Paraschiv, Andrei Tiberiu Cucuruz, Gabriela Sbarcea, Elisa Popescu, Teodor Badea

    In this study, a CoCrMo-based metallic alloy was manufactured using a 3D-printing method with metallic powder and a laser-based 3D printer. The obtained material was immersed in a simulated body fluid (SBF) similar to blood plasma and kept 2 months at 37 °C and in relative motion against the SBF in order to mimic the real motion of body fluids against an implant. At determined time intervals (24, 72, 168, 336, and 1344 h), both the metallic sample and SBF were characterized from a physical-chemical point of view in order to assess the alloy’s behaviour in the SBF. Firstly, the CoCrMo based metallic sample was characterized by scanning electron microscopy (SEM) for assessing surface corrosion and X-ray diffraction (XRD) for determining if and/or what kind of spontaneous protective layer was formed on the surface; secondly, the SBF was characterized by pH, electrical conductivity (EC), and inductively coupled plasma mass spectroscopy (ICP-MS) for assessing the metal ion release. We determined that a 3D-printed CoCrMo alloy does not represent a potential biological hazard in terms of the concentration of metal ion releases, since it forms, in a relatively short period of time, a protective CoCr layer on its exposed surface.


  • Open Access

    In-Depth Comparative Assessment of Different Metallic Biomaterials in Simulated Body Fluid

    by Radu Mirea, Andrei Tiberiu Cucuruz, Laurentiu Constantin Ceatra, Teodor Badea, Iuliana Biris, Elisa Popescu, Alexandru Paraschiv, Razvan Ene, Gabriela Sbarcea, Mihaiella Cretu

    Invitro experiments have been conducted on metallic biomaterials used for orthopedic implants in order to determine their behavior when immersed in simulated body fluid (SBF). Thus, 3Ti-based metallic biomaterial samples already available on the marked were purchased and immersed in simulated blood plasma, and kept at 37 °C for 4 months. In-depth characterization consisted of a wide series of structural characterizations of both the samples and SBF. Sample analysis consisted of the following: optical (OM) and scanning electron microscopy (SEM) in order to establish the surface and deep corrosion, mass gain/loss assessment for determining the metallic ions loss and/or protective layer formation, and X-ray diffraction in order to establish if and what kind of layers are formed. SBF analysis consisted of using inductively coupled plasma mass spectroscopy (ICP-MS) in order to establish if and/or how many metallic ions have dissociated from the metallic samples into the SBF, and measurements of pH and electrical conductivity. The key findings of the research are as follows: during the four months while kept in SBF, the samples show surface corrosion degradation and protective layer generation. Also, the amount of metallic ions dissociated into the SBF is making them suitable for use. Taking into account that it is highly improbable for such a large area of metal as the one considered within this work to be exposed to real body fluids and that all the samples have developed protective oxide films, the overall conclusion is that they are appropriate for implant use.


  • Open Access

    An Experimental Investigation to Use the Biodiesel Resulting from Recycled Sunflower Oil, and Sunflower Oil with Palm Oil as Fuels for Aviation Turbo-Engines

    by Grigore Cican, Marius Deaconu, Radu Mirea, Laurentiu Constantin Ceatra, Mihaiella Cretu

    The paper is presenting the experimental analysis of the use of biodiesel from waste sunflower oil and a blend of sunflower oil with palm oil as fuel for aviation turbo-engines. A comparative analysis for fuel mixtures made of Jet A + 5% Aeroshell 500 Oil (Ke) with 10%, 30%, and 50% for each bio-fuel type has been performed and Ke has been used as reference. Firstly, the following physical and chemical properties were determined: density, viscosity, flash point, freezing point, calorific power. Then, elemental analysis and Fourier transform infrared spectroscopy (FTIR) analysis were conducted for Ke, biodiesel obtained from recycled sunflower oil (SF), biodiesel obtained from blending recycled sunflower oil, and recycled palm oil (SFP), and for each fuel blend. Secondly, experimental tests of the blends have been conducted on the Jet Cat P80® micro-turbo engine (Gunt Hamburg, Barsbüttel, Germany). The tests have been conducted at different engine working regimes as follows: idle, cruise, intermediate, and maximum. For each regime, a one-minute testing period was chosen, and the engine parameters have been monitored. The turbo engine instrumentation recorded the temperature after the compressor and before the turbine, the fuel consumption and air flow, pressure inside the combustion chamber, and generated thrust. The burning efficiency and the specific consumption have been calculated for all four above-mentioned regimes and for all fuel blends. Two accelerometers have been installed on the engine’s support to register radial and axial vibrations allowing the assessment of engine stability.


  • Open Access

    Investigating the Use of Recycled Pork Fat-Based Biodiesel in Aviation Turbo Engines

    by Grigore Cican, Marius Deaconu, Radu Mirea, Laurentiu Ceatra, Mihaiella Cretu, Tănase Dobre

    This paper presents an analysis of the possibility of using recycled pork fat-based biodiesel as fuel for aviation turbo-engines. The analysis consists of the assessment of four blends of Jet A kerosene with 10%, 30%, 50%, and 100% biodiesel and pure Jet A that was used as reference in the study. The first part of the paper presents the physical-chemical properties of the blends: density, viscosity, flash point, freezing point, and calorific power. Through Fourier transform infrared spectroscopy (FTIR) analysis, a benchmark was performed on the mixtures of Jet A with 10%, 20%, 30%, 50%, and 100% biodiesel compared with Jet A. The second part of the paper presents the test results of these blends used for fuelling a Jet Cat P80 turbo engine at the Turbo Engines Laboratory of the Aerospace Engineering Faculty of Polyethnic University of Bucharest. These functional tests were performed using different operating regimes as follows: idle, cruise, intermediate, and maximum. For each regime, a testing period of around 1 min was selected and the engine parameters were monitored during the test execution. The burning efficiency was calculated for the maximum regime for all mixtures. To evaluate the functioning stability of the turbo engine using biodiesel, two accelerometers were mounted on the engine support that recorded the radial and axial vibrations. Moreover, to assess the burning stability and to identify other acoustic spectral components when biodiesel is used, two microphones were placed near the jet region. A comparative analysis between blends was made by taking the Jet A fuel as reference.