Arvid Abel
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Arvid Abel has a total of 36 co-authors. Here are the top co-authors by number of shared publications:
- Christian Klose
Institut für Werkstoffkunde (Materials Science), Leibniz University Hannover, Garbsen, Germany
3 shared publications Jörg Hermsdorf
Additive Manufacturing Department Laser Zentrum Hannover e.V. Hollerithallee 8 30419 Hannover Germany
3 shared publicationsStefan Kaierle
3 shared publicationsAnna Buling
2 shared publicationsAnutsek Sharma
2 shared publicationsHannes Holländer
Additive Manufacturing Department Laser Zentrum Hannover e.V. Hollerithallee 8 30419 Hannover Germany
2 shared publications
Latest Publications
- Open Access
- 23 February 2025
- Published by Wiley in Advanced Engineering Materials
- Vol. 27 (14)
Influence of a Hydrogen Addition to the Inert Gas and Subsequent Heat Treatments on the Microstructure and Mechanical Properties of Magnesium WE43 Fabricated by PBF‐LB/M
Additive manufacturing of magnesium alloys shows great potential for producing patient‐specific resorbable implants or lightweight parts. However, due to the reactive behavior, especially in the laser‐based powder bed fusion (PBF‐LB) fabrication process, the processing window to manufacture almost pore‐free parts is narrow compared to other materials such as titanium or steel. This article investigates optimal processing conditions for the PBF‐LB/M of WE43. To reduce the reactivity of the magnesium melt by limiting the interaction with remaining oxygen, a 3 vol% hydrogen admixture to the argon inert gas is investigated. Furthermore, long‐duration heat treatments are investigated in the range of 250–350 °C for 48 h. This study evaluates the impact of both methods on mechanical properties and microstructure. Although hydrogen seems to have no significant influence on the relative density, the microstructure, and the phase composition, it can slightly increase the tensile strength and elongation at break in the as‐built state. A heat treatment of 250 °C can increase the elongation at the break without impeding the tensile strength.
- 23 February 2025
- Published by Wiley in Advanced Engineering Materials
- Vol. 27 (14)
Open AccessInfluence of a Hydrogen Addition to the Inert Gas and Subsequent Heat Treatments on the Microstructure and Mechanical Properties of Magnesium WE43 Fabricated by PBF‐LB/M
Additive manufacturing of magnesium alloys shows great potential for producing patient‐specific resorbable implants or lightweight parts. However, due to the reactive behavior, especially in the laser‐based powder bed fusion (PBF‐LB) fabrication process, the processing window to manufacture almost pore‐free parts is narrow compared to other materials such as titanium or steel. This article investigates optimal processing conditions for the PBF‐LB/M of WE43. To reduce the reactivity of the magnesium melt by limiting the interaction with remaining oxygen, a 3 vol% hydrogen admixture to the argon inert gas is investigated. Furthermore, long‐duration heat treatments are investigated in the range of 250–350 °C for 48 h. This study evaluates the impact of both methods on mechanical properties and microstructure. Although hydrogen seems to have no significant influence on the relative density, the microstructure, and the phase composition, it can slightly increase the tensile strength and elongation at break in the as‐built state. A heat treatment of 250 °C can increase the elongation at the break without impeding the tensile strength.
- Open Access
- 1 December 2024
- Published by Wiley in Advanced Engineering Materials
- Vol. 27 (14)
Development of Ternary Magnesium Alloys for Laser Powder Bed Fusion: Optimizing Oxide Layer Thickness
Magnesium alloys pose challenges in additive manufacturing, due to the difference between the melting temperature of magnesium oxide (2825 °C) on the powder particles and the boiling point of metallic magnesium (1093 °C). A promising approach to overcoming the difficulties is the reduction of the thickness of the high‐melting oxide layer on the surface of the particles. Magnesium alloys, each containing varying amounts of strontium, neodymium, and yttrium, are cast and subsequently analyzed in terms of their microstructures, mechanical properties, oxide layer thicknesses, and corrosion behavior. Alloying magnesium with strontium results in a reduction of the oxide layer thickness, which reaches a minimum of 0.5 wt% strontium content. The presence of rare earth elements increases the strength of the alloys, although the inclusion of neodymium results in an increase in the oxide layer thicknesses. On the other hand, the oxide layer thickness remains unaffected when alloying with yttrium. However, further increases in strontium content up to the monolithic phase Mg17Sr2 have been found to result in a reduced effect on the open‐circuit potential. Further studies should be conducted to investigate the suitability of strontium as an alloying element to reduce the oxide layer thickness of magnesium particles.
- 1 December 2024
- Published by Wiley in Advanced Engineering Materials
- Vol. 27 (14)
Open AccessDevelopment of Ternary Magnesium Alloys for Laser Powder Bed Fusion: Optimizing Oxide Layer Thickness
Magnesium alloys pose challenges in additive manufacturing, due to the difference between the melting temperature of magnesium oxide (2825 °C) on the powder particles and the boiling point of metallic magnesium (1093 °C). A promising approach to overcoming the difficulties is the reduction of the thickness of the high‐melting oxide layer on the surface of the particles. Magnesium alloys, each containing varying amounts of strontium, neodymium, and yttrium, are cast and subsequently analyzed in terms of their microstructures, mechanical properties, oxide layer thicknesses, and corrosion behavior. Alloying magnesium with strontium results in a reduction of the oxide layer thickness, which reaches a minimum of 0.5 wt% strontium content. The presence of rare earth elements increases the strength of the alloys, although the inclusion of neodymium results in an increase in the oxide layer thicknesses. On the other hand, the oxide layer thickness remains unaffected when alloying with yttrium. However, further increases in strontium content up to the monolithic phase Mg17Sr2 have been found to result in a reduced effect on the open‐circuit potential. Further studies should be conducted to investigate the suitability of strontium as an alloying element to reduce the oxide layer thickness of magnesium particles.
- Open Access
- 29 November 2024
- Published by Elsevier in Acta Astronautica
- Vol. 228, 30-41
Influence of ambient pressure on laser beam melting of lunar regolith simulant
- 29 November 2024
- Published by Elsevier in Acta Astronautica
- Vol. 228, 30-41
Open AccessInfluence of ambient pressure on laser beam melting of lunar regolith simulant
- Open Access
- 24 May 2024
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 9 (3) , 683-694
PBF-LB of large-area magnesium WE43 structures surface-enhanced by plasma electrolytic oxidation
Due to the improved understanding of the industry, additive manufacturing processes are becoming increasingly accepted for fabricating complex lightweight components. The focus of the magnesium research is primarily on small implant structures. Due to challenges in the manufacturing process and oxidation behavior, large structures for lightweight components are mainly fabricated with titanium. This paper expands the scope of the laser-based powder bed fusion (PBF-LB) of larger-area magnesium parts with surface enhancement using the Ultraceramic® by the plasma electrolytic oxidation (PEO). For this purpose, the PBF-LB process development for cylindric structures with a diameter of 31 mm is carried out. The processing strategies are adapted for a crack and porosity free process. To mitigate the inherent oxidation of the biodegradable WE43 and reduce the surface wear in tribologically challenging applications, the additively manufactured magnesium is modified by the Ultraceramic®. The thickness of the ceramic surface could be tailored between 10 and 40 µm, while enclosing adhering powder particles of the PBF. Electrochemical impedance spectroscopy showed an increased resistance to corrosion by an increased modulus |Z0.01| by a factor of 658. The tribological behavior was characterized in pin-on-disc experiments and showed a decrease of surface wear down to 7.9 × 10–6 mm3/N·m up to a Hertzian pressure of 720 MPa tested by a tungsten carbide ball. Therefore, the synthesis of the PBF-LB of large-area magnesium parts and the PEO of the Ultraceramic® enables lightweight components for challenging oxidative and tribological conditions in real world applications.
- 24 May 2024
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 9 (3) , 683-694
Open AccessPBF-LB of large-area magnesium WE43 structures surface-enhanced by plasma electrolytic oxidation
Due to the improved understanding of the industry, additive manufacturing processes are becoming increasingly accepted for fabricating complex lightweight components. The focus of the magnesium research is primarily on small implant structures. Due to challenges in the manufacturing process and oxidation behavior, large structures for lightweight components are mainly fabricated with titanium. This paper expands the scope of the laser-based powder bed fusion (PBF-LB) of larger-area magnesium parts with surface enhancement using the Ultraceramic® by the plasma electrolytic oxidation (PEO). For this purpose, the PBF-LB process development for cylindric structures with a diameter of 31 mm is carried out. The processing strategies are adapted for a crack and porosity free process. To mitigate the inherent oxidation of the biodegradable WE43 and reduce the surface wear in tribologically challenging applications, the additively manufactured magnesium is modified by the Ultraceramic®. The thickness of the ceramic surface could be tailored between 10 and 40 µm, while enclosing adhering powder particles of the PBF. Electrochemical impedance spectroscopy showed an increased resistance to corrosion by an increased modulus |Z0.01| by a factor of 658. The tribological behavior was characterized in pin-on-disc experiments and showed a decrease of surface wear down to 7.9 × 10–6 mm3/N·m up to a Hertzian pressure of 720 MPa tested by a tungsten carbide ball. Therefore, the synthesis of the PBF-LB of large-area magnesium parts and the PEO of the Ultraceramic® enables lightweight components for challenging oxidative and tribological conditions in real world applications.
- Open Access
Development of a Laser Powder Bed Fusion Process Tailored for the Additive Manufacturing of High-Quality Components Made of the Commercial Magnesium Alloy WE43
Additive manufacturing (AM) has become increasingly important over the last decade and the quality of the products generated with AM technology has strongly improved. The most common metals that are processed by AM techniques are steel, titanium (Ti) or aluminum (Al) alloys. However, the proportion of magnesium (Mg) in AM is still negligible, possibly due to the poor processability of Mg in comparison to other metals. Mg parts are usually produced by various casting processes and the experiences in additive manufacturing of Mg are still limited. To address this issue, a parameter screening was conducted in the present study with experiments designed to find the most influential process parameters. In a second step, these parameters were optimized in order to fabricate parts with the highest relative density. This experiment led to processing parameters with which specimens with relative densities above 99.9% could be created. These high-density specimens were then utilized in the fabrication of test pieces with several different geometries, in order to compare the material properties resulting from both the casting process and the powder bed fusion (PBF-LB) process. In this comparison, the compositions of the occurring phases and the alloys’ microstructures as well as the mechanical properties were investigated. Typically, the microstructure of metal parts, produced by PBF-LB, consisted of much finer grains compared to as-cast parts. Consequently, the strength of Mg parts generated by PBF-LB could be further increased.
Open AccessDevelopment of a Laser Powder Bed Fusion Process Tailored for the Additive Manufacturing of High-Quality Components Made of the Commercial Magnesium Alloy WE43
Additive manufacturing (AM) has become increasingly important over the last decade and the quality of the products generated with AM technology has strongly improved. The most common metals that are processed by AM techniques are steel, titanium (Ti) or aluminum (Al) alloys. However, the proportion of magnesium (Mg) in AM is still negligible, possibly due to the poor processability of Mg in comparison to other metals. Mg parts are usually produced by various casting processes and the experiences in additive manufacturing of Mg are still limited. To address this issue, a parameter screening was conducted in the present study with experiments designed to find the most influential process parameters. In a second step, these parameters were optimized in order to fabricate parts with the highest relative density. This experiment led to processing parameters with which specimens with relative densities above 99.9% could be created. These high-density specimens were then utilized in the fabrication of test pieces with several different geometries, in order to compare the material properties resulting from both the casting process and the powder bed fusion (PBF-LB) process. In this comparison, the compositions of the occurring phases and the alloys’ microstructures as well as the mechanical properties were investigated. Typically, the microstructure of metal parts, produced by PBF-LB, consisted of much finer grains compared to as-cast parts. Consequently, the strength of Mg parts generated by PBF-LB could be further increased.