Marcio F. A. de Souza
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Marcio F. A. de Souza has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- M. T. de Melo
Departamento de Eletrônica e Sistemas ‐ Grupo de Fotônica Universidade Federal de Pernambuco (UFPE) Pernambuco 50740‐530 Brazil
2 shared publications A. L. Bezerra
Departamento de Eletronica e Sistemas - Grupo de Fotonica, Universidade Federal de Pernambuco (UFPE), Av. Academico Helio Ramos, S/N, 50740-530 Recife, Pernambuco, Brazil
1 shared publicationB. G. M. de Oliveira
Departamento de Eletronica e Sistemas - Grupo de Fotonica, Universidade Federal de Pernambuco (UFPE), Av. Academico Helio Ramos, S/N, 50740-530 Recife, Pernambuco, Brazil
1 shared publicationF. R. L. e Silva
Departamento de Eletronica e Sistemas - Grupo de Fotonica, Universidade Federal de Pernambuco (UFPE), Av. Academico Helio Ramos, S/N, 50740-530 Recife, Pernambuco, Brazil
1 shared publication- F. R. L. e Silva
Departamento de Eletrônica e Sistemas, Universidade Federal de Pernambuco 50740-530, Recife, PE, Brasil
1 shared publication Fabio R. L. e Silva
Dept. de Eletron. e Sist., Univ. Fed. de Pernambuco (UFPE), Recife, Brazil
1 shared publication
Latest Publications
- Open Access
- 1 September 2020
- Published by FapUNIFESP (SciELO) in Journal of Microwaves, Optoelectronics and Electromagnetic Applications
- Vol. 19 (3) , 396-406
A Novel Fully Integrated 4-Bit IFM Subsystem Using Band-Stop Filters
In this paper a 2-4 GHz microstrip IFM (Instantaneous Frequency Measurement) subsystem that uses Wilkinson power dividers, frequency discriminators based on band-stop filters and a DC arduino section is reported. The device uses band-stop filters as an alternative to delay lines, commonly used for IFM. The resonators are responsible for frequency adjustment, according to half guided wavelength resonator length, and the distance between the transmission line and the resonator. A fully micro-controlled 125 MHz resolution IFM subsystem is designed and tested. Results of the IFM subsystem composed by filters, 4-way power dividers and an Arduino board are described.
- 1 September 2020
- Published by FapUNIFESP (SciELO) in Journal of Microwaves, Optoelectronics and Electromagnetic Applications
- Vol. 19 (3) , 396-406
Open AccessA Novel Fully Integrated 4-Bit IFM Subsystem Using Band-Stop Filters
In this paper a 2-4 GHz microstrip IFM (Instantaneous Frequency Measurement) subsystem that uses Wilkinson power dividers, frequency discriminators based on band-stop filters and a DC arduino section is reported. The device uses band-stop filters as an alternative to delay lines, commonly used for IFM. The resonators are responsible for frequency adjustment, according to half guided wavelength resonator length, and the distance between the transmission line and the resonator. A fully micro-controlled 125 MHz resolution IFM subsystem is designed and tested. Results of the IFM subsystem composed by filters, 4-way power dividers and an Arduino board are described.
- 25 August 2009
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 57 (9) , 2224-2231
Discriminators for Instantaneous Frequency Measurement Subsystem Based on Open-Loop Resonators
The authors have studied a new way to design an instantaneous frequency measurement subsystem (IFMS). The method is based on bandstop filters. The device uses rectangular open-loop resonators instead of delay lines. The resonance frequency is adjusted by a resonator perimeter that must be approximately a half-wavelength long, and also by coupling distance between the resonators and the main transmission line. Simulated and experimental results are presented for a 5-bit IFMS.
- 25 August 2009
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 57 (9) , 2224-2231
Discriminators for Instantaneous Frequency Measurement Subsystem Based on Open-Loop Resonators
The authors have studied a new way to design an instantaneous frequency measurement subsystem (IFMS). The method is based on bandstop filters. The device uses rectangular open-loop resonators instead of delay lines. The resonance frequency is adjusted by a resonator perimeter that must be approximately a half-wavelength long, and also by coupling distance between the resonators and the main transmission line. Simulated and experimental results are presented for a 5-bit IFMS.
- 1 October 2008
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 36-39
A Novel LSB Discriminator for a 5 bit IFM Subsystem Based on Microstrip Band-Stop Filter
The authors have studied a new way to design IFM (Instantaneous Frequency Measurement) subsystem. The method is based on band-stop filters. The IFM uses rectangular open loop resonators instead of delay lines. The resonance frequency is adjusted by resonator perimeter, that must be half guided wavelength, and also by coupling distance between the resonators and the main transmission line. A LSB (least significant bit) discriminator of an IFM subsystem with resolution of 62.5 MHz is designed. The device has been fabricated on RT6010.2 substrate of thickness h=1.27 mm. A full wave EM simulator is used to obtain the frequency response.
- 1 October 2008
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 36-39
A Novel LSB Discriminator for a 5 bit IFM Subsystem Based on Microstrip Band-Stop Filter
The authors have studied a new way to design IFM (Instantaneous Frequency Measurement) subsystem. The method is based on band-stop filters. The IFM uses rectangular open loop resonators instead of delay lines. The resonance frequency is adjusted by resonator perimeter, that must be half guided wavelength, and also by coupling distance between the resonators and the main transmission line. A LSB (least significant bit) discriminator of an IFM subsystem with resolution of 62.5 MHz is designed. The device has been fabricated on RT6010.2 substrate of thickness h=1.27 mm. A full wave EM simulator is used to obtain the frequency response.
- 18 June 2008
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 50 (9) , 2422-2426
GSM open‐loop duplexer filter with internal stubs
- 18 June 2008
- Published by Wiley in Microwave and Optical Technology Letters
- Vol. 50 (9) , 2422-2426
GSM open‐loop duplexer filter with internal stubs