Baoju Liu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Baoju Liu has a total of 48 co-authors. Here are the top co-authors by number of shared publications:
Bingjiang Chen
3 shared publications- Jinyan Shi
School of Civil Engineering, Central South University, Changsha, People’s Republic of China
3 shared publications Junyi Jiang
3 shared publications- Wei Zhuang
School of Civil Engineering, Central South University, Changsha 410075, China
3 shared publications Zhihai He
3 shared publicationsChen Huang
2 shared publications
Latest Publications
- Open Access
The Coupling Effects of Thermosetting Polyurethane Crosslinking and an Aggregate Skeleton on the Mechanical Response of Asphalt Mixtures
To clarify the coupled effects of the thermosetting polyurethane (PU) crosslinked binder network and aggregate gradation on the multi-mode mechanical response of asphalt mixtures, three representative 13 mm gradations—stone mastic asphalt (SMA-13), dense-skeleton asphalt concrete (SAC-13), and dense-graded asphalt concrete (AC-13)—were used to prepare polyurethane-modified asphalt (PUA) mixtures, with an SMA-13 styrene–butadiene–styrene (SBS)-modified asphalt mixture employed as the control. Uniaxial penetration and dynamic modulus tests were conducted to systematically characterize strength, deformation, fracture, and viscoelastic responses under direct tension, crack propagation, localized compression–shear loading, and cyclic loading. Under the same SMA gradation and binder–aggregate ratio, SMA-PUA exhibited a 212.5% increase in peak tensile stress, a 29.2% reduction in peak strain, and increases of 76.3% and 92.8% in penetration strength and the penetration modulus, respectively, relative to SMA-SBS, demonstrating the enhanced load-bearing and stress transfer capacity provided by the three-dimensional PU chemical network. Gradation had a limited influence on tensile strength but a pronounced effect on penetration and fracture behavior. In terms of penetration strength and the penetration modulus, the mixtures followed the order SAC-PUA > SMA-PUA > AC-PUA, the SCB maximum fracture strength followed the same order and the maximum tensile strain showed the reverse trend. Dynamic testing showed clear temperature–frequency dependence for all PUA mixtures, with SAC-PUA generally maintaining higher dynamic stiffness. At the common test temperature of 35 °C, SMA-PUA exhibited a higher dynamic modulus and a smaller, more stable phase angle than SMA-SBS. Overall, the macroscopic mechanical response of thermosetting PUA mixtures is governed by the synergy between the high-strength crosslinked binder network and the aggregate skeleton: the PU network establishes the basic load-bearing level, while gradation further regulates stiffness, crack propagation, and deformation compatibility.
Open AccessThe Coupling Effects of Thermosetting Polyurethane Crosslinking and an Aggregate Skeleton on the Mechanical Response of Asphalt Mixtures
To clarify the coupled effects of the thermosetting polyurethane (PU) crosslinked binder network and aggregate gradation on the multi-mode mechanical response of asphalt mixtures, three representative 13 mm gradations—stone mastic asphalt (SMA-13), dense-skeleton asphalt concrete (SAC-13), and dense-graded asphalt concrete (AC-13)—were used to prepare polyurethane-modified asphalt (PUA) mixtures, with an SMA-13 styrene–butadiene–styrene (SBS)-modified asphalt mixture employed as the control. Uniaxial penetration and dynamic modulus tests were conducted to systematically characterize strength, deformation, fracture, and viscoelastic responses under direct tension, crack propagation, localized compression–shear loading, and cyclic loading. Under the same SMA gradation and binder–aggregate ratio, SMA-PUA exhibited a 212.5% increase in peak tensile stress, a 29.2% reduction in peak strain, and increases of 76.3% and 92.8% in penetration strength and the penetration modulus, respectively, relative to SMA-SBS, demonstrating the enhanced load-bearing and stress transfer capacity provided by the three-dimensional PU chemical network. Gradation had a limited influence on tensile strength but a pronounced effect on penetration and fracture behavior. In terms of penetration strength and the penetration modulus, the mixtures followed the order SAC-PUA > SMA-PUA > AC-PUA, the SCB maximum fracture strength followed the same order and the maximum tensile strain showed the reverse trend. Dynamic testing showed clear temperature–frequency dependence for all PUA mixtures, with SAC-PUA generally maintaining higher dynamic stiffness. At the common test temperature of 35 °C, SMA-PUA exhibited a higher dynamic modulus and a smaller, more stable phase angle than SMA-SBS. Overall, the macroscopic mechanical response of thermosetting PUA mixtures is governed by the synergy between the high-strength crosslinked binder network and the aggregate skeleton: the PU network establishes the basic load-bearing level, while gradation further regulates stiffness, crack propagation, and deformation compatibility.
- Open Access
- 1 September 2026
- Published by Springer Nature in npj Materials Sustainability
- Vol. 4 (1) , 39
Producing high-quality recycled aggregate concrete: a novel biomimetic strengthening strategy
- 1 September 2026
- Published by Springer Nature in npj Materials Sustainability
- Vol. 4 (1) , 39
Open AccessProducing high-quality recycled aggregate concrete: a novel biomimetic strengthening strategy
- 20 April 2026
- Published by Elsevier in Environmental Research
- Vol. 301, 124555
Sustainable utilization of lithium slag through chemical activation: Development of low-carbon cementitious materials based on cement-lithium slag-limestone
- 20 April 2026
- Published by Elsevier in Environmental Research
- Vol. 301, 124555
Sustainable utilization of lithium slag through chemical activation: Development of low-carbon cementitious materials based on cement-lithium slag-limestone
- 27 March 2025
- Published by Elsevier in Construction and Building Materials
- Vol. 473
Hydration properties and microstructure evolution of recycled concrete powder under the action of alkanolamines
- 27 March 2025
- Published by Elsevier in Construction and Building Materials
- Vol. 473
Hydration properties and microstructure evolution of recycled concrete powder under the action of alkanolamines
- Open Access
Modification Mechanism and Performance of High-Content Polyurethane-Modified Asphalt
To explore the influence of the polyurethane blending ratio on the micro-characteristics of polyurethane-modified asphalt, three samples of the modified asphalt with different blending ratios (40%, 50%, and 60%) were prepared. Fourier transform infrared spectroscopy (FTIR), atomic force microscopy (AFM), and scanning electron microscopy (SEM) were employed to elucidate the modification mechanism of polyurethane-modified asphalt. To investigate how the preparation method affects the performance of polyurethane-modified asphalt mixtures, two different preparation methods, namely internal blending and external blending, were adopted. The road performance of the polyurethane-modified asphalt mixtures was evaluated through the utilization of rutting tests, low-temperature trabecular bending tests, and freeze–thaw splitting tests. The FTIR test results indicate that during the modification of polyurethane, there is a change in both the intensity and position of the absorption peak, which affects the local arrangement of the molecular structure. Upon reaching a polyurethane blending ratio of 50%, a cross-linked network structure that is similar to polyurethane is formed. The results of the AFM test demonstrate that an increase in polyurethane content results in a corresponding increase in surface roughness. At a polyurethane content of 50%, the curing reaction is most effective, which is beneficial for enhancing the bonding performance between the asphalt and the aggregate, thereby enhancing the overall water stability of the mixture. The results of the scanning electron microscopy (SEM) tests indicate that the microstructure is more stable when the polyurethane content is 50%. The results of the performance test of the polyurethane-modified asphalt mixture indicate that the dynamic stability of the polyurethane-modified asphalt mixture is approximately four times that of the SBS-modified asphalt mixture. The flexural tensile strength and maximum flexural strain of the polyurethane-modified asphalt mixture are, respectively, 1.5 and 3.2 times those of the SBS-modified asphalt mixture, indicating that its anti-deformation ability is stronger in a low-temperature environment, and it is found that the low-temperature performance of the mixture prepared with the internal blending method is better than that with the external blending method. The splitting strength of the polyurethane asphalt mixture before and after freezing and thawing is greater than that of an SBS asphalt mixture: before freezing and thawing, by about 3.8 times; after freezing and thawing, by about 3 times. Although the freezing and thawing of the polyurethane mixture has damage, it still meets the requirements of the use of pavement materials. It can be observed that the incorporation of polyurethane alters the internal structure of the asphalt, which markedly enhances the properties of the asphalt mixture and offers a novel perspective on the development of modified asphalt materials.
Open AccessModification Mechanism and Performance of High-Content Polyurethane-Modified Asphalt
To explore the influence of the polyurethane blending ratio on the micro-characteristics of polyurethane-modified asphalt, three samples of the modified asphalt with different blending ratios (40%, 50%, and 60%) were prepared. Fourier transform infrared spectroscopy (FTIR), atomic force microscopy (AFM), and scanning electron microscopy (SEM) were employed to elucidate the modification mechanism of polyurethane-modified asphalt. To investigate how the preparation method affects the performance of polyurethane-modified asphalt mixtures, two different preparation methods, namely internal blending and external blending, were adopted. The road performance of the polyurethane-modified asphalt mixtures was evaluated through the utilization of rutting tests, low-temperature trabecular bending tests, and freeze–thaw splitting tests. The FTIR test results indicate that during the modification of polyurethane, there is a change in both the intensity and position of the absorption peak, which affects the local arrangement of the molecular structure. Upon reaching a polyurethane blending ratio of 50%, a cross-linked network structure that is similar to polyurethane is formed. The results of the AFM test demonstrate that an increase in polyurethane content results in a corresponding increase in surface roughness. At a polyurethane content of 50%, the curing reaction is most effective, which is beneficial for enhancing the bonding performance between the asphalt and the aggregate, thereby enhancing the overall water stability of the mixture. The results of the scanning electron microscopy (SEM) tests indicate that the microstructure is more stable when the polyurethane content is 50%. The results of the performance test of the polyurethane-modified asphalt mixture indicate that the dynamic stability of the polyurethane-modified asphalt mixture is approximately four times that of the SBS-modified asphalt mixture. The flexural tensile strength and maximum flexural strain of the polyurethane-modified asphalt mixture are, respectively, 1.5 and 3.2 times those of the SBS-modified asphalt mixture, indicating that its anti-deformation ability is stronger in a low-temperature environment, and it is found that the low-temperature performance of the mixture prepared with the internal blending method is better than that with the external blending method. The splitting strength of the polyurethane asphalt mixture before and after freezing and thawing is greater than that of an SBS asphalt mixture: before freezing and thawing, by about 3.8 times; after freezing and thawing, by about 3 times. Although the freezing and thawing of the polyurethane mixture has damage, it still meets the requirements of the use of pavement materials. It can be observed that the incorporation of polyurethane alters the internal structure of the asphalt, which markedly enhances the properties of the asphalt mixture and offers a novel perspective on the development of modified asphalt materials.
- Open Access
Mechanical Properties of Polyurethane Mixture and Load Response Behaviour of Polyurethane Composite Pavement
Finite element numerical simulation calculation of pavement structure load response is widely applied; however, there is still a lack of research on the polyurethane (PU) mixture composite pavement load response. The mechanical characteristics of PU mixture composite pavement are not well understood, and there is a lack of research on typical pavement structures of PU mixtures, which limits their application in pavement structures. Therefore, herein, the mechanical properties of PU mixtures are analysed using the dynamic modulus test, uniaxial penetration test, and fatigue test. Further, the finite element theory calculation method is used to realize the load response calculation of orthogonal design composite pavement structure. The results show that PU mixtures exhibit more obvious elastic characteristics and have good shear resistance, fatigue stability, and temperature stability, and can be used as shear and anti-fatigue layers. The structure of ‘4 cm SMA-13 + 5 cm PUM-20 + 6 cm PUM-25 + semi-rigid base’ is recommended for the PU mixture composite structure. In comparison to typical asphalt pavement, the analysis shows that except for shear stress, temperature has little effect on the load response of PU composite pavement structures, while high temperatures lead to a significant increase in the load response of typical asphalt pavement structures. The PU composite pavement can bear greater loads and has a reduced thickness of its surface layer by about 3 cm in comparison to conventional pavement. The results of this study provide theoretical support for the design of PU mixture pavement structures and promote the popularization and application of PU mixture pavement.
Open AccessMechanical Properties of Polyurethane Mixture and Load Response Behaviour of Polyurethane Composite Pavement
Finite element numerical simulation calculation of pavement structure load response is widely applied; however, there is still a lack of research on the polyurethane (PU) mixture composite pavement load response. The mechanical characteristics of PU mixture composite pavement are not well understood, and there is a lack of research on typical pavement structures of PU mixtures, which limits their application in pavement structures. Therefore, herein, the mechanical properties of PU mixtures are analysed using the dynamic modulus test, uniaxial penetration test, and fatigue test. Further, the finite element theory calculation method is used to realize the load response calculation of orthogonal design composite pavement structure. The results show that PU mixtures exhibit more obvious elastic characteristics and have good shear resistance, fatigue stability, and temperature stability, and can be used as shear and anti-fatigue layers. The structure of ‘4 cm SMA-13 + 5 cm PUM-20 + 6 cm PUM-25 + semi-rigid base’ is recommended for the PU mixture composite structure. In comparison to typical asphalt pavement, the analysis shows that except for shear stress, temperature has little effect on the load response of PU composite pavement structures, while high temperatures lead to a significant increase in the load response of typical asphalt pavement structures. The PU composite pavement can bear greater loads and has a reduced thickness of its surface layer by about 3 cm in comparison to conventional pavement. The results of this study provide theoretical support for the design of PU mixture pavement structures and promote the popularization and application of PU mixture pavement.
- Top Cited Papers
- 1 March 2021
- Published by Elsevier in Journal of Cleaner Production
- Vol. 288
A green ultra-lightweight chemically foamed concrete for building exterior: A feasibility study
- 1 March 2021
- Published by Elsevier in Journal of Cleaner Production
- Vol. 288
Top Cited PapersA green ultra-lightweight chemically foamed concrete for building exterior: A feasibility study
- Top Cited Papers
- 1 February 2021
- Published by Elsevier in Construction and Building Materials
- Vol. 272
New perspectives on utilization of sequestration technologies in cement-based materials- 1 February 2021
- Published by Elsevier in Construction and Building Materials
- Vol. 272
Top Cited PapersNew perspectives on utilization of sequestration technologies in cement-based materials - 1 December 2020
- Published by American Society of Civil Engineers (ASCE) in Journal of Construction Engineering and Management
- Vol. 146 (12) , 04020130
Experimental Studies and Microstructure Analysis for Rapid-Hardening Cement Emulsified Asphalt Mortar
A cement emulsified asphalt mortar (CEAM) made with calcium sulfoaluminate cement was prepared and tested indoors, which has a relatively slight environmental impact compared with ordinary Portland cement. The effects of asphalt to cement ( ) and water to cement ( ) ratios on the performance of CEAM were systematically evaluated, such as the fresh properties, mechanical properties, volume deformation, temperature dependence, permeability, and frost resistance. Meanwhile, the microstructure images and void characteristics were also obtained by computed tomography technology and scanning electron microscope. The results indicated that with the increase of ratio, the flow time, setting time, and air content of fresh CEAM increase, while the slump flow decreases. The fast-hardening CEAM has higher early strength, which decreases with the and ratios increasing. In addition, the ratio also has a significant influence on the long-term performance of CEAM. High emulsified asphalt content will reduce shrinkage, temperature dependence, and impermeability, but will increase its frost resistance. In addition, different emulsified asphalt and cement contents have a significant effect on microstructure and pore characteristics of CEAM, which directly determines its macroscopic properties. This paper contributes to the structure formation of calcium sulfoaluminate CEAM and provides a reference scheme for the construction of track slabs in winter.- 1 December 2020
- Published by American Society of Civil Engineers (ASCE) in Journal of Construction Engineering and Management
- Vol. 146 (12) , 04020130
Experimental Studies and Microstructure Analysis for Rapid-Hardening Cement Emulsified Asphalt Mortar
A cement emulsified asphalt mortar (CEAM) made with calcium sulfoaluminate cement was prepared and tested indoors, which has a relatively slight environmental impact compared with ordinary Portland cement. The effects of asphalt to cement ( ) and water to cement ( ) ratios on the performance of CEAM were systematically evaluated, such as the fresh properties, mechanical properties, volume deformation, temperature dependence, permeability, and frost resistance. Meanwhile, the microstructure images and void characteristics were also obtained by computed tomography technology and scanning electron microscope. The results indicated that with the increase of ratio, the flow time, setting time, and air content of fresh CEAM increase, while the slump flow decreases. The fast-hardening CEAM has higher early strength, which decreases with the and ratios increasing. In addition, the ratio also has a significant influence on the long-term performance of CEAM. High emulsified asphalt content will reduce shrinkage, temperature dependence, and impermeability, but will increase its frost resistance. In addition, different emulsified asphalt and cement contents have a significant effect on microstructure and pore characteristics of CEAM, which directly determines its macroscopic properties. This paper contributes to the structure formation of calcium sulfoaluminate CEAM and provides a reference scheme for the construction of track slabs in winter.