Yiteng Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Yiteng Wang has a total of 35 co-authors. Here are the top co-authors by number of shared publications:
- Minjoo Larry Lee
University of Illinois Urbana-Champaign
2 shared publications Xizheng Fang
2 shared publicationsAdrian Birge
University of Illinois Urbana-Champaign, Champaign, IL, USA
1 shared publication- Atom O. Watanabe
Department of Electrical and Computer Engineering, Georgia Institute of Technology, Atlanta, GA, 30332 USA
1 shared publication Bora Kim
1 shared publication- Bora Kim
University of Illinois Urbana-Champaign, Champaign, IL, USA
1 shared publication
Latest Publications
- 15 December 2025
- Published by Optica Publishing Group in Optical Materials Express
- Vol. 16 (1) , 32
InP quantum dot lasers: from growth to devices [Invited]
We review progress on the growth and device performance of InP quantum dot lasers emitting in the red spectral region. InAs quantum dot lasers with emission at 1.3 μ m are the most heavily developed quantum dot devices due to their potential for temperature-insensitive operation in optical data communication applications. However, InP quantum dot lasers have become the subject of renewed interest due to the advent of low-loss visible integrated photonic platforms with applications in quantum information, biosensing, and virtual/augmented reality displays. High-performance devices have been grown by both metalorganic chemical vapor deposition and molecular beam epitaxy, and we review the strengths and challenges of each growth technique. Like their InAs counterparts, InP quantum dot lasers have also proven to be tolerant of crystalline defects, making them amenable to monolithic integration on lattice-mismatched substrates such as silicon. Finally, we discuss promising directions for future work in the field, including surface-emitting lasers, mode-locked lasers, and methods of expanding the range of emission wavelengths to both shorter and longer wavelengths.
- 15 December 2025
- Published by Optica Publishing Group in Optical Materials Express
- Vol. 16 (1) , 32
InP quantum dot lasers: from growth to devices [Invited]
We review progress on the growth and device performance of InP quantum dot lasers emitting in the red spectral region. InAs quantum dot lasers with emission at 1.3 μ m are the most heavily developed quantum dot devices due to their potential for temperature-insensitive operation in optical data communication applications. However, InP quantum dot lasers have become the subject of renewed interest due to the advent of low-loss visible integrated photonic platforms with applications in quantum information, biosensing, and virtual/augmented reality displays. High-performance devices have been grown by both metalorganic chemical vapor deposition and molecular beam epitaxy, and we review the strengths and challenges of each growth technique. Like their InAs counterparts, InP quantum dot lasers have also proven to be tolerant of crystalline defects, making them amenable to monolithic integration on lattice-mismatched substrates such as silicon. Finally, we discuss promising directions for future work in the field, including surface-emitting lasers, mode-locked lasers, and methods of expanding the range of emission wavelengths to both shorter and longer wavelengths.
- 22 October 2025
- Published by Optica Publishing Group in Optica
- Vol. 12 (11) , 1697
Embedded growth of visible InP quantum dot lasers in silicon nitride photonic integrated circuits
Integrated photonics using visible light is rapidly emerging as a powerful platform for applications including quantum information, biosensing, and displays. We present heteroepitaxial growth of visible red InP quantum dot lasers within pockets etched into SiN x /Si photonic integrated circuits (PICs) for on-chip light sources and amplifiers. While epitaxial 1.3 µm InAs quantum dot lasers embedded within Si PICs were recently demonstrated, similar integration of red lasers remains unexplored. We achieve a low threshold current density of 450A/cm 2 with emission at 752 nm and uncoupled single-facet output power exceeding 10 mW at room temperature under continuous-wave injection. Although further work is needed to experimentally demonstrate coupling between the embedded lasers and SiN x waveguides, our results represent a critical step toward dense monolithic integration of visible red optical gain on PICs for on-chip applications.
- 22 October 2025
- Published by Optica Publishing Group in Optica
- Vol. 12 (11) , 1697
Embedded growth of visible InP quantum dot lasers in silicon nitride photonic integrated circuits
Integrated photonics using visible light is rapidly emerging as a powerful platform for applications including quantum information, biosensing, and displays. We present heteroepitaxial growth of visible red InP quantum dot lasers within pockets etched into SiN x /Si photonic integrated circuits (PICs) for on-chip light sources and amplifiers. While epitaxial 1.3 µm InAs quantum dot lasers embedded within Si PICs were recently demonstrated, similar integration of red lasers remains unexplored. We achieve a low threshold current density of 450A/cm 2 with emission at 752 nm and uncoupled single-facet output power exceeding 10 mW at room temperature under continuous-wave injection. Although further work is needed to experimentally demonstrate coupling between the embedded lasers and SiN x waveguides, our results represent a critical step toward dense monolithic integration of visible red optical gain on PICs for on-chip applications.
- Open Access
- 8 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 15 (1) , 87-94
AlGaAsP Distributed Bragg Reflectors for GaAsP/Si Solar Cells
We investigate (Al)GaAsP distributed Bragg reflectors (DBRs) on Si (001) to improve the quantum efficiency (QE) of 1.7 eV GaAsP solar cells in GaAsP/Si tandem devices. Samples were grown on Si (001) by molecular beam epitaxy and consisted of a 2.1 $\mu \mathrm{m}$ GaAsP/GaP buffer followed by a ∼2 $\mu \mathrm{m}$ DBR with 20 periods of GaAsP/Al x Ga 1- x AsP alternating layers. Two different DBR designs were studied with x = 0.4 and x = 0.8, both targeting a peak reflectance wavelength of 700 nm. The average threading dislocation density on the DBRs was 1.4 × 10 7 cm −2 , suitable for high-performance GaAsP cells. The reflectance profiles matched well to simulations, and the GaAsP/Al 0.8 Ga 0.2 AsP DBR had a significantly higher peak reflectance and reflectance bandwidth than the GaAsP/Al 0.4 Ga 0.6 AsP DBR due to the higher refractive index contrast. QE simulations of GaAsP cells showed an improvement of ∼1 mA/cm 2 in short-circuit current density with a DBR, which should enable a ∼5% relative efficiency boost in the GaAsP cell and superior current matching to a Si bottom cell in tandem devices.
- 8 November 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Photovoltaics
- Vol. 15 (1) , 87-94
Open AccessAlGaAsP Distributed Bragg Reflectors for GaAsP/Si Solar Cells
We investigate (Al)GaAsP distributed Bragg reflectors (DBRs) on Si (001) to improve the quantum efficiency (QE) of 1.7 eV GaAsP solar cells in GaAsP/Si tandem devices. Samples were grown on Si (001) by molecular beam epitaxy and consisted of a 2.1 $\mu \mathrm{m}$ GaAsP/GaP buffer followed by a ∼2 $\mu \mathrm{m}$ DBR with 20 periods of GaAsP/Al x Ga 1- x AsP alternating layers. Two different DBR designs were studied with x = 0.4 and x = 0.8, both targeting a peak reflectance wavelength of 700 nm. The average threading dislocation density on the DBRs was 1.4 × 10 7 cm −2 , suitable for high-performance GaAsP cells. The reflectance profiles matched well to simulations, and the GaAsP/Al 0.8 Ga 0.2 AsP DBR had a significantly higher peak reflectance and reflectance bandwidth than the GaAsP/Al 0.4 Ga 0.6 AsP DBR due to the higher refractive index contrast. QE simulations of GaAsP cells showed an improvement of ∼1 mA/cm 2 in short-circuit current density with a DBR, which should enable a ∼5% relative efficiency boost in the GaAsP cell and superior current matching to a Si bottom cell in tandem devices.
- Open Access
- 17 July 2023
- Published by AIP Publishing in Applied Physics Letters
- Vol. 123 (3)
8.1 μ m-emitting InP-based quantum cascade laser grown on Si by metalorganic chemical vapor deposition
This study presents the growth and characterization of an 8.1 μm-emitting, InGaAs/AlInAs/InP-based quantum cascade laser (QCL) formed on an InP-on-Si composite template by metalorganic chemical vapor deposition (MOCVD). First, for the composite-template formation, a GaAs buffer layer was grown by solid-source molecular-beam epitaxy on a commercial (001) GaP/Si substrate, thus forming a GaAs/GaP/Si template. Next, an InP metamorphic buffer layer (MBL) structure was grown atop the GaAs/GaP/Si template by MOCVD, followed by the MOCVD growth of the full QCL structure. The top-surface morphology of the GaAs/GaP/Si template before and after the InP MBL growth was assessed via atomic force microscopy, over a 100 μm2 area, and no antiphase domains were found. The average threading dislocation density (TDD) for the GaAs/GaP/Si template was found to be ∼1 × 109 cm−2, with a slightly lower defect density of ∼7.9 × 108 cm−2 after the InP MBL growth. The lasing performance of the QCL structure grown on Si was compared to that of its counterpart grown on InP native substrate and found to be quite similar. That is, the threshold-current density of the QCL on Si, for deep-etched ridge-guide devices with uncoated facets, is somewhat lower than that for its counterpart on native InP substrate, 1.50 vs 1.92 kA/cm2, while the maximum output power per facet is 1.64 vs 1.47 W. These results further demonstrate the resilience of QCLs to relatively high residual TDD values.
- 17 July 2023
- Published by AIP Publishing in Applied Physics Letters
- Vol. 123 (3)
Open Access8.1 μ m-emitting InP-based quantum cascade laser grown on Si by metalorganic chemical vapor deposition
This study presents the growth and characterization of an 8.1 μm-emitting, InGaAs/AlInAs/InP-based quantum cascade laser (QCL) formed on an InP-on-Si composite template by metalorganic chemical vapor deposition (MOCVD). First, for the composite-template formation, a GaAs buffer layer was grown by solid-source molecular-beam epitaxy on a commercial (001) GaP/Si substrate, thus forming a GaAs/GaP/Si template. Next, an InP metamorphic buffer layer (MBL) structure was grown atop the GaAs/GaP/Si template by MOCVD, followed by the MOCVD growth of the full QCL structure. The top-surface morphology of the GaAs/GaP/Si template before and after the InP MBL growth was assessed via atomic force microscopy, over a 100 μm2 area, and no antiphase domains were found. The average threading dislocation density (TDD) for the GaAs/GaP/Si template was found to be ∼1 × 109 cm−2, with a slightly lower defect density of ∼7.9 × 108 cm−2 after the InP MBL growth. The lasing performance of the QCL structure grown on Si was compared to that of its counterpart grown on InP native substrate and found to be quite similar. That is, the threshold-current density of the QCL on Si, for deep-etched ridge-guide devices with uncoated facets, is somewhat lower than that for its counterpart on native InP substrate, 1.50 vs 1.92 kA/cm2, while the maximum output power per facet is 1.64 vs 1.47 W. These results further demonstrate the resilience of QCLs to relatively high residual TDD values.
- 21 September 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. PP (00189480) , 1
Ultrathin Antenna-Integrated Glass-Based Millimeter-Wave Package With Through-Glass Vias
This article presents the design and demonstration of a high-bandwidth antenna-in-package (AiP) module focusing on low-loss interconnects and Yagi-Uda antenna performance fabricated on a 100-μm low coefficient-of-thermal-expansion (CTE) glass for the 28-GHz band. It shows the modeling, design, and characterization of key technology building blocks along with the process development of advanced 3-D glass packages. The building blocks include impedance-matched antenna-to-die signal transitions, Yagi-Uda antenna, and 3-D active-passive integration with backside die assembly on 100-μm glass substrates. The design and stack-up optimization of antenna-integrated millimeter-wave (mm-wave) modules is discussed. Process development to achieve high-density interconnects and precise dimensional control in multilayered thin glass-based packages is also described. The characterization results of the key technology building blocks show an insertion loss of 0.021 dB per through-package via (TPV), leading to the whole-chain loss of less than 1 dB and a return loss lower than 20 dB. The fabricated Yagi-Uda antenna features high repeatability of wide bandwidth due to the process control enabled by glass substrates. The antenna measurements show a bandwidth of 28.2%, which covers the entire 28-GHz fifth-generation (5G) frequency bands (n257, n258, and n261). The flip-chip assembled low-noise amplifier with 80-μm solder balls shows a maximum gain of 20 dB as desired. The performance of the glass-based package integrated antennas is benchmarked to other 5G substrate technologies, such as organic laminates or co-fired ceramic-based substrates.
- 21 September 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. PP (00189480) , 1
Ultrathin Antenna-Integrated Glass-Based Millimeter-Wave Package With Through-Glass Vias
This article presents the design and demonstration of a high-bandwidth antenna-in-package (AiP) module focusing on low-loss interconnects and Yagi-Uda antenna performance fabricated on a 100-μm low coefficient-of-thermal-expansion (CTE) glass for the 28-GHz band. It shows the modeling, design, and characterization of key technology building blocks along with the process development of advanced 3-D glass packages. The building blocks include impedance-matched antenna-to-die signal transitions, Yagi-Uda antenna, and 3-D active-passive integration with backside die assembly on 100-μm glass substrates. The design and stack-up optimization of antenna-integrated millimeter-wave (mm-wave) modules is discussed. Process development to achieve high-density interconnects and precise dimensional control in multilayered thin glass-based packages is also described. The characterization results of the key technology building blocks show an insertion loss of 0.021 dB per through-package via (TPV), leading to the whole-chain loss of less than 1 dB and a return loss lower than 20 dB. The fabricated Yagi-Uda antenna features high repeatability of wide bandwidth due to the process control enabled by glass substrates. The antenna measurements show a bandwidth of 28.2%, which covers the entire 28-GHz fifth-generation (5G) frequency bands (n257, n258, and n261). The flip-chip assembled low-noise amplifier with 80-μm solder balls shows a maximum gain of 20 dB as desired. The performance of the glass-based package integrated antennas is benchmarked to other 5G substrate technologies, such as organic laminates or co-fired ceramic-based substrates.