A. S. Chimanpure
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
A. S. Chimanpure has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
- Ahmet Kahraman
Department of Mechanical and Aerospace Engineering, The Ohio State University, Columbus, OH 43210
2 shared publications - Ahmet Dindar
Department of Mechanical and, Aerospace Engineering, The Ohio State University, 201 W. 19th Avenue, Columbus, OH 43210
1 shared publication - David Talbot
Department of Mechanical and Aerospace Engineering, The Ohio State University, Columbus, OH 43210
1 shared publication
Latest Publications
- 27 August 2021
- Published by ASME International in Journal of Tribology
- Vol. 144 (5)
Mechanical Power Losses of Ball Bearings: Model and Experimental Validation
A tribo-dynamic model of ball bearings is proposed to predict their load-dependent (mechanical) power losses. The model combines (i) a transient, point contact mixed elastohydrodynamic lubrication (EHL) formulation to simulate the mechanics of the load carrying lubricated ball-race interfaces and (ii) a singularity-free dynamics model and establishes the two-way coupling between them that dictates power losses. The dynamic model uses a vectoral formulation with Euler parameters. The EHL model is capable of capturing two-dimensional contact kinematics, velocity variations across the contact as well as asperity interactions of rough contact surfaces. Resultant contact surface shear distributions are processed to predict mechanical power losses of example ball bearings operating under combined radial and axial forces. An experimental setup is introduced for measurement of the power losses of rolling-element bearings. Sets of measurements taken by using the same example ball bearings are compared with those predicted by the model to assess its accuracy in predicting mechanical power loss of a ball bearing within wide ranges of axial and radial forces.
- 27 August 2021
- Published by ASME International in Journal of Tribology
- Vol. 144 (5)
Mechanical Power Losses of Ball Bearings: Model and Experimental Validation
A tribo-dynamic model of ball bearings is proposed to predict their load-dependent (mechanical) power losses. The model combines (i) a transient, point contact mixed elastohydrodynamic lubrication (EHL) formulation to simulate the mechanics of the load carrying lubricated ball-race interfaces and (ii) a singularity-free dynamics model and establishes the two-way coupling between them that dictates power losses. The dynamic model uses a vectoral formulation with Euler parameters. The EHL model is capable of capturing two-dimensional contact kinematics, velocity variations across the contact as well as asperity interactions of rough contact surfaces. Resultant contact surface shear distributions are processed to predict mechanical power losses of example ball bearings operating under combined radial and axial forces. An experimental setup is introduced for measurement of the power losses of rolling-element bearings. Sets of measurements taken by using the same example ball bearings are compared with those predicted by the model to assess its accuracy in predicting mechanical power loss of a ball bearing within wide ranges of axial and radial forces.
- 27 October 2020
- Published by ASME International in Journal of Tribology
- Vol. 143 (6) , 1-27
A Transient Mixed Elastohydrodynamic Lubrication Model for Helical Gear Contacts
In this study, a non-Newtonian, transient, isothermal, mixed elastohydrodynamic lubrication (EHL) model is proposed for helical gear contacts. The model accounts for nonelliptical contacts subject to spatially varying sliding and rolling velocity fields that are not aligned with any principal axis of the contact region, which is the case for helical gear contacts. The time-varying changes pertaining to key contact parameters and relative motion of roughness profiles on mating tooth surfaces are captured simultaneously to follow the contact from the root to the tip of a tooth while accounting for the transient effect due to relative motions of the roughness profiles. Actual tooth load distributions, contact kinematics, and compliances of helical gear contacts are provided to this model by an existing helical gear load distribution model. Measured three-dimensional roughness profiles covering the entire meshing zone are incorporated in the analyses to investigate its impact on the EHL conditions as well as mechanical power loss. Results of a parametric sensitivity study are presented to demonstrate the influence of operating conditions and surface roughness on the EHL behavior and the resultant gear mesh mechanical power loss of an example helical gear pair. The accuracy of the proposed mixed-EHL model is assessed by comparing the mechanical power loss predictions to available experimental results.
- 27 October 2020
- Published by ASME International in Journal of Tribology
- Vol. 143 (6) , 1-27
A Transient Mixed Elastohydrodynamic Lubrication Model for Helical Gear Contacts
In this study, a non-Newtonian, transient, isothermal, mixed elastohydrodynamic lubrication (EHL) model is proposed for helical gear contacts. The model accounts for nonelliptical contacts subject to spatially varying sliding and rolling velocity fields that are not aligned with any principal axis of the contact region, which is the case for helical gear contacts. The time-varying changes pertaining to key contact parameters and relative motion of roughness profiles on mating tooth surfaces are captured simultaneously to follow the contact from the root to the tip of a tooth while accounting for the transient effect due to relative motions of the roughness profiles. Actual tooth load distributions, contact kinematics, and compliances of helical gear contacts are provided to this model by an existing helical gear load distribution model. Measured three-dimensional roughness profiles covering the entire meshing zone are incorporated in the analyses to investigate its impact on the EHL conditions as well as mechanical power loss. Results of a parametric sensitivity study are presented to demonstrate the influence of operating conditions and surface roughness on the EHL behavior and the resultant gear mesh mechanical power loss of an example helical gear pair. The accuracy of the proposed mixed-EHL model is assessed by comparing the mechanical power loss predictions to available experimental results.