Lu Huang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Lu Huang has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
Miao Sun
National Institute of Metrology, Beijing, 100029, CHINA
4 shared publicationsWei Li
National Institute of Metrology (NIM), Beijing, China
2 shared publicationsXin Jia
National Institute of Metrology, Beijing, 100029, CHINA
2 shared publicationsChanghong Xu
National Institute of Metrology, Beijing, China
1 shared publication- Chengming Li
Institute for Advanced Materials and Technology, University of Science and Technology Beijing, Beijing 100083, China
1 shared publication - Dan Guo
State Key Laboratory of Tribology in Advanced Equipment, Tsinghua University, Beijing 100084, China
1 shared publication
Latest Publications
- Open Access
- 1 February 2026
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 3174 (1)
Tensile load measurement of titanium bolts with detailed uncertainty analysis based on acoustoelastic theory by using an ultrasonic sensor
Titanium alloy fasteners are widely used in the aerospace industry. The assembly quality is critical to the reliability and safety of different kinds of components. Limited by the precision and detection efficiency, traditional methods such as the torque coefficient method and the strain gauge method can no longer meet the requirements of rapid, high-precision measurement. The acoustoelasticity method is a fast, precise, and non-destructive method that provides a solution to the above problems. This study focuses on the measurement of tensile load applied to Ti-6Al-4V (TC4) bolts. Stepwise loads are gradually and accurately applied on TC4 bolts, high-frequency echo signals are recorded, and the time-of-flight (TOF) can be calculated correspondingly. Supplemented by a precise calibration procedure, the linear fitting equation of tensile load and TOF based on acoustoelastic theory has been established. Experiment results show that, within (5 – 45) kN tensile load range, the typical relative error is below 5%. The calculated relative expanded uncertainty is around 6.0% ( k = 2). Taking sample dispersion into consideration, the relative expanded uncertainty of the bolt population can be statistically calculated within 8.5% ( k = 2).
- 1 February 2026
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 3174 (1)
Open AccessTensile load measurement of titanium bolts with detailed uncertainty analysis based on acoustoelastic theory by using an ultrasonic sensor
Titanium alloy fasteners are widely used in the aerospace industry. The assembly quality is critical to the reliability and safety of different kinds of components. Limited by the precision and detection efficiency, traditional methods such as the torque coefficient method and the strain gauge method can no longer meet the requirements of rapid, high-precision measurement. The acoustoelasticity method is a fast, precise, and non-destructive method that provides a solution to the above problems. This study focuses on the measurement of tensile load applied to Ti-6Al-4V (TC4) bolts. Stepwise loads are gradually and accurately applied on TC4 bolts, high-frequency echo signals are recorded, and the time-of-flight (TOF) can be calculated correspondingly. Supplemented by a precise calibration procedure, the linear fitting equation of tensile load and TOF based on acoustoelastic theory has been established. Experiment results show that, within (5 – 45) kN tensile load range, the typical relative error is below 5%. The calculated relative expanded uncertainty is around 6.0% ( k = 2). Taking sample dispersion into consideration, the relative expanded uncertainty of the bolt population can be statistically calculated within 8.5% ( k = 2).
- Open Access
- 12 January 2024
- Published by Tsinghua University Press in Friction
- Vol. 12 (4) , 618-631
Origin and evolution of false brinelling and fretting corrosion under rolling conditions
Rolling bearings working in oscillating applications often suffer from false brinelling and fretting corrosion that limit their service life. At present, the study of oscillation-induced failures is primarily dominated by a large number of sliding and bench tests. However, most of the previous work are not able to fully describe the two closely related but different failure mechanisms. In this study, the origin and evolution of the two failures are thoroughly investigated under strictly controlled oscillating rolling conditions. The results show that failure evolves from false brinelling to fretting corrosion under dry friction conditions regardless of the oscillation amplitude. This process is accompanied by a large area peeling and serious oxidation, and the oxygen content increases from 2.50 wt% to 21.22 wt%. Oxidation is a crucial factor in the evolution of false brinelling into fretting corrosion. However, the distribution of microwear and oxygen content depend on the oscillation amplitude. Under lubrication conditions, the friction coefficient (COF) is smaller in the initial stage and led to local slip or transient instability of rolling elements. Therefore, the size of the wear marks and COF increased and appeared to be larger than those under a dry friction condition. However, grease can separate the contact surfaces, only surface deformation owing to false brinelling and slight damage at the roughness level occurred. The evolution of false brinelling and fretting corrosion is also closely related to residual stress. False brinelling often occurrs with residual stress accomulation, meanwhile, the residual stress increases from 120 to 300 MPa. When peeling occurs, residual stress is released. The failure pattern transformed from false brinelling to fretting corrosion and is accompanied by oxidation. So far, none of investigation is able to show satisfactory evolution of oscillating-induced failures, this study may contribute to more scientific understanding of rolling bearings against long-run reciprocating oscillating wear.
- 12 January 2024
- Published by Tsinghua University Press in Friction
- Vol. 12 (4) , 618-631
Open AccessOrigin and evolution of false brinelling and fretting corrosion under rolling conditions
Rolling bearings working in oscillating applications often suffer from false brinelling and fretting corrosion that limit their service life. At present, the study of oscillation-induced failures is primarily dominated by a large number of sliding and bench tests. However, most of the previous work are not able to fully describe the two closely related but different failure mechanisms. In this study, the origin and evolution of the two failures are thoroughly investigated under strictly controlled oscillating rolling conditions. The results show that failure evolves from false brinelling to fretting corrosion under dry friction conditions regardless of the oscillation amplitude. This process is accompanied by a large area peeling and serious oxidation, and the oxygen content increases from 2.50 wt% to 21.22 wt%. Oxidation is a crucial factor in the evolution of false brinelling into fretting corrosion. However, the distribution of microwear and oxygen content depend on the oscillation amplitude. Under lubrication conditions, the friction coefficient (COF) is smaller in the initial stage and led to local slip or transient instability of rolling elements. Therefore, the size of the wear marks and COF increased and appeared to be larger than those under a dry friction condition. However, grease can separate the contact surfaces, only surface deformation owing to false brinelling and slight damage at the roughness level occurred. The evolution of false brinelling and fretting corrosion is also closely related to residual stress. False brinelling often occurrs with residual stress accomulation, meanwhile, the residual stress increases from 120 to 300 MPa. When peeling occurs, residual stress is released. The failure pattern transformed from false brinelling to fretting corrosion and is accompanied by oxidation. So far, none of investigation is able to show satisfactory evolution of oscillating-induced failures, this study may contribute to more scientific understanding of rolling bearings against long-run reciprocating oscillating wear.
- Open Access
The Effect of Interlayer Microstructure on the Thermal Boundary Resistance of GaN-on-Diamond Substrate
Diamond has the highest thermal conductivity of any natural material. It can be used to integrate with GaN to dissipate heat from AlGaN/GaN high electron mobility transistor (HEMT) channels. Much past work has investigated the thermal properties of GaN-on-diamond devices, especially the thermal boundary resistance between the diamond and GaN (TBReff,Dia/GaN). However, the effect of SiNx interlayer structure on the thermal resistance of GaN-on-diamond devices is less investigated. In this work, we explore the role of different interfaces in contributing to the thermal boundary resistance of the GaN-on-diamond layers, specifically using 100 nm layer of SiNx, 80 nm layer of SiNx, 100 nm layer of SiNx with a 20 nm × 20 nm periodic structure. Through combination with time-domain thermoreflectance measurement and microstructural analysis, we were able to determine that a patterning SiNx interlayer provided the lower thermal boundary resistance (32.2 ± 1.8 m2KGW−1) because of the diamond growth seeding and the diamond nucleation surface. In addition, the patterning of the SiNx interlayer can effectively improve the interface bonding force and diamond nucleation density and reduce the thermal boundary resistance of the GaN-on-diamond. This enables significant improvement in heat dissipation capability of GaN-on-diamond with respect to GaN wafers.
Open AccessThe Effect of Interlayer Microstructure on the Thermal Boundary Resistance of GaN-on-Diamond Substrate
Diamond has the highest thermal conductivity of any natural material. It can be used to integrate with GaN to dissipate heat from AlGaN/GaN high electron mobility transistor (HEMT) channels. Much past work has investigated the thermal properties of GaN-on-diamond devices, especially the thermal boundary resistance between the diamond and GaN (TBReff,Dia/GaN). However, the effect of SiNx interlayer structure on the thermal resistance of GaN-on-diamond devices is less investigated. In this work, we explore the role of different interfaces in contributing to the thermal boundary resistance of the GaN-on-diamond layers, specifically using 100 nm layer of SiNx, 80 nm layer of SiNx, 100 nm layer of SiNx with a 20 nm × 20 nm periodic structure. Through combination with time-domain thermoreflectance measurement and microstructural analysis, we were able to determine that a patterning SiNx interlayer provided the lower thermal boundary resistance (32.2 ± 1.8 m2KGW−1) because of the diamond growth seeding and the diamond nucleation surface. In addition, the patterning of the SiNx interlayer can effectively improve the interface bonding force and diamond nucleation density and reduce the thermal boundary resistance of the GaN-on-diamond. This enables significant improvement in heat dissipation capability of GaN-on-diamond with respect to GaN wafers.
- 7 March 2021
- Published by Springer Nature in Optoelectronics Letters
- Vol. 17 (3) , 170-175
Precise measurement of gold nanorods by using depolarized dynamic light scattering apparatus
- 7 March 2021
- Published by Springer Nature in Optoelectronics Letters
- Vol. 17 (3) , 170-175
Precise measurement of gold nanorods by using depolarized dynamic light scattering apparatus
- Open Access
- 26 January 2021
- Published by Tsinghua University Press in Friction
- Vol. 10 (3) , 388-397
Direct observation of the impact of water droplets on oil replenishment in EHD lubricated contacts
Water is one of the most significant causes of lubrication failure. There is little research on the direct observation of the impact of water on lubrication properties. In this study, the influence of water on oil replenishment under different elastohydrodynamic (EHD) lubricating conditions is evaluated using optical interferometry and infrared microscopy, and a dimensionless criterion when water influences the film thickness is proposed. Evidence shows that the scour displacing effect and emulsification of water/oil are the main reasons for the reduction in film thickness. Once a water droplet enters an oil reservoir around the critical contact zone, it hardly moves away. This aggravates starvation, reduces the center film thickness of the contact, and leads to lubrication failure of the mechanical components.
- 26 January 2021
- Published by Tsinghua University Press in Friction
- Vol. 10 (3) , 388-397
Open AccessDirect observation of the impact of water droplets on oil replenishment in EHD lubricated contacts
Water is one of the most significant causes of lubrication failure. There is little research on the direct observation of the impact of water on lubrication properties. In this study, the influence of water on oil replenishment under different elastohydrodynamic (EHD) lubricating conditions is evaluated using optical interferometry and infrared microscopy, and a dimensionless criterion when water influences the film thickness is proposed. Evidence shows that the scour displacing effect and emulsification of water/oil are the main reasons for the reduction in film thickness. Once a water droplet enters an oil reservoir around the critical contact zone, it hardly moves away. This aggravates starvation, reduces the center film thickness of the contact, and leads to lubrication failure of the mechanical components.
- 20 September 2020
- Published by Springer Nature in Applied Physics B
- Vol. 126 (10) , 1-9
Precise measurement of particle size in colloid system based on the development of multiple-angle dynamic light scattering apparatus
- 20 September 2020
- Published by Springer Nature in Applied Physics B
- Vol. 126 (10) , 1-9
Precise measurement of particle size in colloid system based on the development of multiple-angle dynamic light scattering apparatus