AKAmid P. Khodadoust

Amid P. Khodadoust

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Amid P. Khodadoust has a total of 27 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Defluoridation of Water Using Al-Mg-Ca Ternary Metal Oxide-Coated Sand in Adsorption Column Study

    by Kiana Modaresahmadi, Amid P. Khodadoust, James Wescott

    Defluoridation of water was investigated in an adsorption column study using Al-Mg-Ca-coated sand (AMCCS), a ternary metal oxide adsorbent with eco-friendly components that were shown to be effective for water defluoridation, in a batch adsorption study. A packed column of the AMCCS sorbent was evaluated as function of column flow rate, solution type, and sorbent recyclability. Adsorption column experiments included two column flow rates of 2 mL/min and 10 mL/min using two different solutions: deionized water and a synthetic solution representative of groundwater. Greater fluoride column adsorption capacity was obtained at the lower flow rate for both solutions, mainly due to longer contact times between solution and AMCCS sorbent. Adsorption of fluoride occurred through physical adsorption, which followed the Langmuir adsorption model and second-order kinetics for deionized water and synthetic solution. A lower AMCCS column fluoride adsorption capacity was observed for the synthetic solution due to the competition from adsorption of other ions in the synthetic solution, whereas fluoride adsorption by the AMCCS column was influenced by interphase mass transfer to a lesser extent using the synthetic solution than deionized water. The re-coating of spent AMCCS sorbent in the adsorption column resulted in effective recycling and reuse of the AMCCS adsorption column for both deionized water and the synthetic solution, rendering the AMCCS adsorption column a recyclable and sustainable flow through water defluoridation system.


  • Open Access

    Defluoridation of Water Using Cu-Mg-Binary-Metal-Oxide-Coated Sand

    by Kiana Modaresahmadi, Amid P. Khodadoust, James Wescott

    Defluoridation of water was evaluated using a copper–magnesium (Cu-Mg) coated sand (CMCS) as a sustainable adsorbent containing binary metal oxides. The CMCS sorbent coating contained mostly amorphous copper and magnesium oxides in the Cu-Mg coating on the crystalline sand surface. Pseudo-second-order kinetics was observed where most fluoride was removed rapidly within an hour. Favorable adsorption occurred according to the Langmuir and Freundlich adsorption equations, while physisorption occurred according to the Dubinin–Radushkevich (D-R) adsorption equation. The adsorption capacity of the CMCS sorbent based on sorbent surface was similar to various other adsorbents with larger adsorbent surface areas, likely due to the efficacy of the Cu-Mg coating despite the CMCS sorbent’s much smaller surface area. Fluoride was adsorbed effectively from pH 3 to pH 11 through adsorption of anionic fluoride onto the CMCS sorbent’s protonated surface with a pHPZC of 10.5, indicative of electrostatic attraction as the main adsorption mechanism. The CMCS sorbent’s re-coating was conducive to successful recycling and reuse of the CMCS sorbent as a sustainable adsorbent for water defluoridation.


  • Open Access

    Adsorption of Fluoride from Water Using Aluminum-Coated Silica Adsorbents: Comparison of Silica Sand and Microcrystalline Silica

    by Kiana Modaresahmadi, Amid P. Khodadoust, James Wescott

    Two aluminum-coated silica adsorbents were evaluated using silica sand and microcrystalline silica as aluminum-oxide-based adsorbents with different crystalline silica base materials. The aluminum coating contained mainly amorphous aluminum oxides for both aluminum-coated silica adsorbents. The adsorption of fluoride onto both adsorbents was favorable according to the Langmuir and Freundlich adsorption equations, while the physical adsorption of fluoride occurred for both adsorbents according to the Dubinin–Raduskevish (D-R) equation. The adsorption of fluoride was stronger for aluminum-coated silica sand based on adsorption parameters from the Langmuir, Freundlich, and D-R adsorption equations, with the stronger binding of fluoride likely due to the observed greater specific adsorption. The adsorption capacity determined using the Langmuir equation was about 7 times greater for aluminum-coated microcrystalline silica primarily due to the 1.22-orders-of-magnitude-larger surface area of aluminum-coated microcrystalline silica, whereas the surface-normalized adsorption capacity was 2.4 times greater for aluminum-coated silica sand, possibly due to more aluminum being present on the surface of silica sand. Fluoride adsorption occurred over a broad pH range from 3 to 10 for both adsorbents, with nearly the same pHPZC of 9.6, while aluminum-coated microcrystalline silica displayed a higher selectivity for fluoride adsorption from different natural water sources.


  • Open Access

    Adsorption of fluoride from water using Al–Mg–Ca ternary metal oxide-coated sand

    by Kiana Modaresahmadi, Amid P. Khodadoust, James Wescott

    An aluminum–magnesium–calcium-coated sand (AMCCS) sorbent was evaluated as a low-cost ternary metal oxide adsorbent for adsorption and removal of fluoride from water with potential application in flow-through water filtration systems. The AMCCS sorbent coating contained mostly amorphous oxides of aluminum, magnesium, and calcium. The adsorption of fluoride occurred in less than an hour, while fluoride adsorption followed pseudo-second-order kinetics. The favorable adsorption of fluoride onto the AMCCS sorbent occurred according to the Langmuir and Freundlich adsorption equations, whereas the physical adsorption of fluoride onto the AMCCS sorbent occurred based on the Dubinin–Radushkevich adsorption equation. The adsorption of fluoride occurred over a broad pH range from 2 to 10.5 with a decrease in adsorption at pH above 10.5, indicative of the adsorption of fluoride onto the positively charged surface of AMCCS sorbent at pH below the AMCCS sorbent pHPZC of 10.4. The AMCCS sorbent was able to remove fluoride from natural waters with appreciable alkalinity, total hardness and total dissolved solids, indicative of AMCCS sorbent selectivity for fluoride adsorption. The AMCCS sorbent was re-coated and reused after several adsorption cycles, rendering the AMCCS sorbent a recyclable and sustainable adsorbent for effective and rapid removal of fluoride from water.


  • Removal of chromium from water using manganese (II, III) oxides coated sand: adsorption and transformation of Cr(VI) and Cr(III)

    by Lisha Wu, Amid P. Khodadoust, Snover Punia

    A manganese coated sand (MCS) sorbent containing manganese (II,III) oxides was developed for adsorption and transformation of chromium [Cr(VI) and Cr(III)] with potential application in flow-through permeable media adsorption filters. Characterization of the MCS sorbent using XRD and XPS showed that the oxides of manganese (II) and manganese (III) were present on the MCS sorbent surface. Adsorption of both Cr(VI) and Cr(III) onto the MCS sorbent occurred over a broad pH range from 3 to 10. Surface charge analysis of the MCS sorbent determined a pHPZC of 7.8, which may facilitate the uptake of both oxy-anionic Cr(VI) species and cationic Cr(III) species. Favorable adsorption of Cr(VI) and Cr(III) onto the MCS sorbent occurred according to the Langmuir and the Freundlich adsorption equations, with a higher adsorption capacity for Cr(III) than Cr(VI). Adsorption parameters from the Langmuir, the Freundlich and the Temkin adsorption equations showed a stronger binding of Cr(VI) than Cr(III). Adsorption of Cr(III) decreased with increasing calcium concentration while adsorption of Cr(VI) decreased with increasing concentration of common anions found in natural water in the following order: phosphate > sulfate> bicarbonate. Transformation of chromium occurred on the surface of the MCS sorbent due to the partial reduction of Cr(VI) and the partial oxidation of Cr(III), which may be attributed to the role of surface manganese (II,III) oxides as either reducing or oxidizing agents. The MCS sorbent is a recyclable and sustainable adsorbent for removal of chromium from water with an environmental impact comparable to ion-exchange technology. GRAPHICAL ABSTRACT


  • Adsorption of hexavalent chromium from water using manganese-aluminum coated sand: Kinetics, equilibrium, effect of pH and ionic strength

    by Snover Punia, Lisha Wu, Amid P. Khodadoust

    Removal of hexavalent chromium [Cr(VI)] from water was evaluated using a low-cost coated sand adsorbent for potential application in a flow-through filter system using permeable adsorption media. Manganese-aluminum coated sand (MACS) was investigated as a hybrid metal oxide based adsorbent due to the potential efficacy of manganese oxide and aluminum oxide for adsorption of Cr(VI) from water. Adsorbent characterization was performed using XRD, SEM/EDX, XPS and BET. Adsorption experiments were performed to determine adsorption capacity and kinetics. The effect of pH, common co-existing ions found in natural water, and the recyclability of adsorbent were investigated. Adsorbent characterization showed that the MACS sorbent contained aluminum oxide, manganese (III) oxide and manganese (IV) oxide. Adsorption followed the Langmuir and Freundlich adsorption equations, indicating favorable adsorption of Cr(VI) onto the MACS sorbent, while results from the Dubinin–Radushkevich equation were suggestive of physical adsorption of Cr(VI). Cr(VI) adsorption onto the MACS sorbent followed pseudo-second order kinetics. The adsorbent was effective in removing Cr(VI) over a broad pH range from 3 to 9.5, while surface charge analysis confirmed the adsorption of Cr(VI) onto the acidic surface of the MACS sorbent with a pHPZC of 9.72. The presence of co-existing ions bicarbonate, sulfate and phosphate in water resulted in a decrease in Cr(VI) uptake in the following order: phosphate > bicarbonate > sulfate. The presence of calcium resulted in a slight increase in Cr(VI) uptake. The MACS sorbent is a recyclable sorbent for adsorption and removal of Cr(VI) from water within 30 minutes of contact time.


  • Removal of arsenic from water using manganese (III) oxide: Adsorption of As(III) and As(V)

    by Kamel Babaeivelni, Amid P. Khodadoust

    Removal of arsenic from water was evaluated with manganese (III) oxide (Mn2O3) as adsorbent. Adsorption of As(III) and As(V) onto Mn2O3 was favorable according to the Langmuir and Freundlich adsorption equilibrium equations, while chemisorption of arsenic occurred according to the Dubinin–Radushkevich equation. Adsorption parameters from the Langmuir, Freundlich, and Temkin equations showed a greater adsorption and removal of As(III) than As(V) by Mn2O3. Maximum removal of As(III) and As(V) occurred at pH 3–9 and at pH 2, respectively, while removal of As(V) in the pH range of 6–9 was 93% (pH 6) to 61% (pH 9) of the maximum removal. Zeta potential measurements for Mn2O3 in As(III) was likely converted to As(V) solutions indicated that As(III) was likely converted to As(V) on the Mn2O3 surface at pH 3–9. Overall, the effective Mn2O3 sorbent rapidly removed As(III) and As(V) from water in the pH range of 6-9 for natural waters.


  • Adsorption and removal of arsenic (V) using crystalline manganese (II,III) oxide: Kinetics, equilibrium, effect of pH and ionic strength

    by Kamel Babaeivelni, Amid P. Khodadoust, Dorin Bogdan

    Manganese (II,III) oxide (Mn3O4) crystalline powder was evaluated as a potential sorbent for removal of arsenic (V) from water. Adsorption isotherm experiments were carried out to determine the adsorption capacity using de-ionized (DI) water, a synthetic solution containing bicarbonate alkalinity, and two natual groundwater samples. Adsorption isotherm data followed the Langmuir and Freundlich equations, indicating favorable adsorption of arsenic (V) onto Mn3O4, while results from the Dubinin–Radushkevich equation were suggestive of chemisorption of arsenic (V). When normalized to the sorbent surface area, the maximum adsorption capacity of Mn3O4 for arsenic (V) was 101 μg m−2, comparable to that of activated alumina. Arsenic (V) adsorption onto Mn3O4 followed pseudo–second-order kinetics. Adsorption of arsenic (V) was greatest at pH 2, while adsorption at pH 7–9 was within 91% of maximum adsorption, whereas adsorption decreased to 32% of maximum adsorption at pH 10. Surface charge analysis confirmed the adsorption of arsenic (V) onto the acidic surface of the Mn3O4 sorbent with a pHPZC of 7.32. The presence of coexisting ions bicarbonate and phosphate resulted in a decrease in arsenic (V) uptake. Comparable adsorption capacities were obtained for the synthetic solution and both groundwater samples. Overall, crystalline Mn3O4 was an effective and viable sorbent for removal of arsenic (V) from natural water, removing greater than 95% of arsenic (V) from a 1 mg L−1 solution within 60 min of contact time.


  • Uptake of arsenic by alkaline soils near alkaline coal fly ash disposal facilities

    by Amid P. Khodadoust, Thomas L. Theis, Ishwar P. Murarka, Pratibha Naithani, Kamel Babaeivelni


  • Transport and Reactivity of Lactate-Modified Nanoscale Iron Particles in PCP-Contaminated Soils

    by Krishna R. Reddy, Amid P. Khodadoust, Kenneth Darko-Kagya

    Remediation of sites contaminated by toxic chlorinated organic compounds by using nanoscale iron particles (NIP) has received great attention owing to their high reactivity resulting from small size and large reactive surface area. However, adequate delivery of NIP into the contaminated zones for in situ remediation applications is difficult because of NIP agglomeration and sedimentation. Different surface modifications of NIP are suggested to enhance the transport of NIP in soils. This study investigated the transport and remediation efficiency of bare NIP and lactate-modified NIP (LMNIP) in field sand contaminated with pentachlorophenol (PCP). Soil column experiments were conducted to investigate the reactivity and transport of NIP and LMNIP at different concentrations (1 and 4 g/L ) under two different constant hydraulic gradients, and the consequent degradation of PCP in the soil. Bare NIP was transported only to limited distances and its distribution through the soil was nonuniform; however, LMNIP w...