Abdallah Cheraitia
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Abdallah Cheraitia has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Abdelmalek Saoud
Process Engineering Department, Faculty of Science and Technology, Université 8 Mai 1945-Guelma, Guelma 24000, Algeria
1 shared publication Basma Al-Najar
1 shared publication- Fouad Boukhelf
Institut de Recherche de la Construction, ESTP-Grande Ecole d’ingénieurs de la Construction, 28 Avenue du Président Wilson, 94230 Cachan, France
1 shared publication Ikram Boukerche
1 shared publication- Laidi Babouri
Department of Physics and Chemistry, Normal Higher School of Technological Education of Skikda, Skikda 21000, Algeria
1 shared publication - Mebrouk Ghougali
Department of Physics, University of El Oued, El Oued, Algeria
1 shared publication
Latest Publications
- Open Access
Sustainable Graphene-like Carbon from Ghars Date Waste for Photothermal-Enhanced Solar Desalination: A Circular Economy Approach
The valorization of agricultural waste into high-value carbon nanomaterials offers dual benefits: it reduces pollution and provides low-cost materials for sustainable technologies. This work synthesizes graphene-like carbon from Ghars date waste via mild KOH-assisted pyrolysis at 1000 °C. The material (G-GhW1000) exhibits a sharp (002) XRD peak at 26.16° (d-spacing = 3.40 Å), a characteristic π → π* transition at 253 nm, and a high C/O ratio of 27.37. Dispersed in tap water (0.5 g/L) by simple hand shaking (without ultrasonication), it serves as a photothermal nanofluid in a modified single-slope solar still (MSS). Under outdoor conditions, the MSS produces 4.69 L·m−2·day−1, which is 18.7% higher than a conventional still, with thermal efficiency rising from 27.2% to 30.8% (with a reproducible 19.0% enhancement in summer). Samples prepared at 800 °C and 900 °C give 4.0% and 6.4% lower yields, while the 1100 °C sample gives only 6.0% improvement, confirming 1000 °C as the optimal temperature. The superior performance at 1000 °C is attributed to the optimal balance between graphitization, deoxygenation, and structural integrity, as evidenced by XRD, FTIR, EDX and UV-Vis analyses. The enhanced performance is linked to higher water temperature (68 °C) and larger ΔT. The distilled water meets WHO standards (TDS 9.35 mg/L, >99.4% reduction) with no detectable graphene-like carbon carryover. This work demonstrates the potential of waste-derived graphene-like carbon as a low-cost additive for solar desalination, addressing water scarcity and waste management within a circular economy framework. To our knowledge, this is the first study to use Ghars date waste-derived graphene-like carbon in a solar still.
Open AccessSustainable Graphene-like Carbon from Ghars Date Waste for Photothermal-Enhanced Solar Desalination: A Circular Economy Approach
The valorization of agricultural waste into high-value carbon nanomaterials offers dual benefits: it reduces pollution and provides low-cost materials for sustainable technologies. This work synthesizes graphene-like carbon from Ghars date waste via mild KOH-assisted pyrolysis at 1000 °C. The material (G-GhW1000) exhibits a sharp (002) XRD peak at 26.16° (d-spacing = 3.40 Å), a characteristic π → π* transition at 253 nm, and a high C/O ratio of 27.37. Dispersed in tap water (0.5 g/L) by simple hand shaking (without ultrasonication), it serves as a photothermal nanofluid in a modified single-slope solar still (MSS). Under outdoor conditions, the MSS produces 4.69 L·m−2·day−1, which is 18.7% higher than a conventional still, with thermal efficiency rising from 27.2% to 30.8% (with a reproducible 19.0% enhancement in summer). Samples prepared at 800 °C and 900 °C give 4.0% and 6.4% lower yields, while the 1100 °C sample gives only 6.0% improvement, confirming 1000 °C as the optimal temperature. The superior performance at 1000 °C is attributed to the optimal balance between graphitization, deoxygenation, and structural integrity, as evidenced by XRD, FTIR, EDX and UV-Vis analyses. The enhanced performance is linked to higher water temperature (68 °C) and larger ΔT. The distilled water meets WHO standards (TDS 9.35 mg/L, >99.4% reduction) with no detectable graphene-like carbon carryover. This work demonstrates the potential of waste-derived graphene-like carbon as a low-cost additive for solar desalination, addressing water scarcity and waste management within a circular economy framework. To our knowledge, this is the first study to use Ghars date waste-derived graphene-like carbon in a solar still.
- Open Access
- 28 February 2026
- Published by International Information and Engineering Technology Association in Annales de Chimie - Science des Matériaux
- Vol. 50 (1) , 87-97
Tailoring Pore Size in Clay Ceramics Using Cornstarch and Reduced Graphene Oxide as Pore-Forming Agents
- 28 February 2026
- Published by International Information and Engineering Technology Association in Annales de Chimie - Science des Matériaux
- Vol. 50 (1) , 87-97
Open AccessTailoring Pore Size in Clay Ceramics Using Cornstarch and Reduced Graphene Oxide as Pore-Forming Agents
- 24 September 2020
- Published by Wiley in International Journal of Applied Ceramic Technology
- Vol. 18 (1) , 70-80
Novel mullite‐cordierite ceramic refractory fabricated from halloysite and talc
This research work aims to fabricate industrial refractory bricks using cheap and abundant kaolin DD 3 constituted of Halloysite. The fabrication process consists on mixing the crushed raw materials (Kaolin/Clay, Fireclay, Talc) with the respective proportions and an optimized granulometry, shaped by a uniaxial hydrostatic pressure of 250 bars, followed by drying at 100°C and sintering at 1300°C. The addition of Talc ‐ at first with water, Fireclay and AP/DD 3 ‐ as a source of MgO promotes the increase of Cordierite formation in order to obtain high heat resistance shock and reduced thermal expansion. Three assays are studied with AP Clay and DD 3 Kaolin weight ratios (100/0, 50/50 and 0/100) % corresponding to (ER 0 , ER 1 and ER 2 ) respectively. Mineralogical analysis results of the new refractory bricks, indicate the presence of Mullite and Cordierite as major phases besides Corundum and Quartz as minor phases. All products (ER 0 , ER 1 and ER 2 ) are found to be argillaceous refractory with Alumina concentration (40 < Al 2 O 3 < 45%, FC 40 group) and a melting point higher than 1600°C. The mechanical resistance of the samples is of the same order of magnitude; reaching 51 MPa.
- 24 September 2020
- Published by Wiley in International Journal of Applied Ceramic Technology
- Vol. 18 (1) , 70-80
Novel mullite‐cordierite ceramic refractory fabricated from halloysite and talc
This research work aims to fabricate industrial refractory bricks using cheap and abundant kaolin DD 3 constituted of Halloysite. The fabrication process consists on mixing the crushed raw materials (Kaolin/Clay, Fireclay, Talc) with the respective proportions and an optimized granulometry, shaped by a uniaxial hydrostatic pressure of 250 bars, followed by drying at 100°C and sintering at 1300°C. The addition of Talc ‐ at first with water, Fireclay and AP/DD 3 ‐ as a source of MgO promotes the increase of Cordierite formation in order to obtain high heat resistance shock and reduced thermal expansion. Three assays are studied with AP Clay and DD 3 Kaolin weight ratios (100/0, 50/50 and 0/100) % corresponding to (ER 0 , ER 1 and ER 2 ) respectively. Mineralogical analysis results of the new refractory bricks, indicate the presence of Mullite and Cordierite as major phases besides Corundum and Quartz as minor phases. All products (ER 0 , ER 1 and ER 2 ) are found to be argillaceous refractory with Alumina concentration (40 < Al 2 O 3 < 45%, FC 40 group) and a melting point higher than 1600°C. The mechanical resistance of the samples is of the same order of magnitude; reaching 51 MPa.