Laidi Babouri
Research Subjects
Laidi Babouri has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Fouad Boukhelf
Institut de Recherche de la Construction, ESTP-Grande Ecole d’ingénieurs de la Construction, 28 Avenue du Président Wilson, 94230 Cachan, France
2 shared publications - S. M. Anas
Department of Civil Engineering, Jamia Millia Islamia, New Delhi 110025, India
2 shared publications - Yassine El Mendili
Institut de Recherche de l’ESTP, École Spéciale des Travaux Publics, 28 Avenue du Président Wilson, 94230 Cachan, France
2 shared publications - Abdallah Cheraitia
Process Engineering Department, Faculty of Science and Technology, Université 8 Mai 1945-Guelma, Guelma 24000, Algeria
1 shared publication - Abdelaziz Hammouda
Materials Geomaterials and Environment Laboratory (LMGE), Faculty of Technology, Department of Civil Engineering, Badji Mokhtar-Annaba University, Annaba, Algeria
1 shared publication - Abdelmalek Saoud
Process Engineering Department, Faculty of Science and Technology, Université 8 Mai 1945-Guelma, Guelma 24000, Algeria
1 shared publication
Latest Publications
- Open Access
Sustainable Graphene-like Carbon from Ghars Date Waste for Photothermal-Enhanced Solar Desalination: A Circular Economy Approach
The valorization of agricultural waste into high-value carbon nanomaterials offers dual benefits: it reduces pollution and provides low-cost materials for sustainable technologies. This work synthesizes graphene-like carbon from Ghars date waste via mild KOH-assisted pyrolysis at 1000 °C. The material (G-GhW1000) exhibits a sharp (002) XRD peak at 26.16° (d-spacing = 3.40 Å), a characteristic π → π* transition at 253 nm, and a high C/O ratio of 27.37. Dispersed in tap water (0.5 g/L) by simple hand shaking (without ultrasonication), it serves as a photothermal nanofluid in a modified single-slope solar still (MSS). Under outdoor conditions, the MSS produces 4.69 L·m−2·day−1, which is 18.7% higher than a conventional still, with thermal efficiency rising from 27.2% to 30.8% (with a reproducible 19.0% enhancement in summer). Samples prepared at 800 °C and 900 °C give 4.0% and 6.4% lower yields, while the 1100 °C sample gives only 6.0% improvement, confirming 1000 °C as the optimal temperature. The superior performance at 1000 °C is attributed to the optimal balance between graphitization, deoxygenation, and structural integrity, as evidenced by XRD, FTIR, EDX and UV-Vis analyses. The enhanced performance is linked to higher water temperature (68 °C) and larger ΔT. The distilled water meets WHO standards (TDS 9.35 mg/L, >99.4% reduction) with no detectable graphene-like carbon carryover. This work demonstrates the potential of waste-derived graphene-like carbon as a low-cost additive for solar desalination, addressing water scarcity and waste management within a circular economy framework. To our knowledge, this is the first study to use Ghars date waste-derived graphene-like carbon in a solar still.
Open AccessSustainable Graphene-like Carbon from Ghars Date Waste for Photothermal-Enhanced Solar Desalination: A Circular Economy Approach
The valorization of agricultural waste into high-value carbon nanomaterials offers dual benefits: it reduces pollution and provides low-cost materials for sustainable technologies. This work synthesizes graphene-like carbon from Ghars date waste via mild KOH-assisted pyrolysis at 1000 °C. The material (G-GhW1000) exhibits a sharp (002) XRD peak at 26.16° (d-spacing = 3.40 Å), a characteristic π → π* transition at 253 nm, and a high C/O ratio of 27.37. Dispersed in tap water (0.5 g/L) by simple hand shaking (without ultrasonication), it serves as a photothermal nanofluid in a modified single-slope solar still (MSS). Under outdoor conditions, the MSS produces 4.69 L·m−2·day−1, which is 18.7% higher than a conventional still, with thermal efficiency rising from 27.2% to 30.8% (with a reproducible 19.0% enhancement in summer). Samples prepared at 800 °C and 900 °C give 4.0% and 6.4% lower yields, while the 1100 °C sample gives only 6.0% improvement, confirming 1000 °C as the optimal temperature. The superior performance at 1000 °C is attributed to the optimal balance between graphitization, deoxygenation, and structural integrity, as evidenced by XRD, FTIR, EDX and UV-Vis analyses. The enhanced performance is linked to higher water temperature (68 °C) and larger ΔT. The distilled water meets WHO standards (TDS 9.35 mg/L, >99.4% reduction) with no detectable graphene-like carbon carryover. This work demonstrates the potential of waste-derived graphene-like carbon as a low-cost additive for solar desalination, addressing water scarcity and waste management within a circular economy framework. To our knowledge, this is the first study to use Ghars date waste-derived graphene-like carbon in a solar still.
- 10 October 2025
- Published by Springer Nature in Innovative Infrastructure Solutions
- Vol. 10 (11) , 1-17
Surface treatment of Alfa fibers to improve mechanical performance and matrix compatibility in sustainable bio-composites
- 10 October 2025
- Published by Springer Nature in Innovative Infrastructure Solutions
- Vol. 10 (11) , 1-17
Surface treatment of Alfa fibers to improve mechanical performance and matrix compatibility in sustainable bio-composites
- Open Access
Assessment of Mechanical Behavior and Microstructure of Unsaturated Polyester Resin Composites Reinforced with Recycled Marble Waste
The quarrying and utilization of natural stones such as marble and granite are growing rapidly in developing countries. However, the processing, cutting, sizing, and shaping of these stones to render them functional generates huge quantities of waste and dust. These materials are often disposed of openly in the environment, and their potentially hazardous nature has negative repercussions on both the environment and human health. In this study, marble waste (MW) was used as a filler in the unsaturated polyester resin (UPR) matrix to enhance performance and characteristics while adding value to the waste and minimizing manufacturing costs. For this purpose, samples of UPR/MW composites were produced with 0, 5, 10, 15, and 20 wt.% of MW incorporated into the UPR. A full characterization that focused on the microstructure, thermal stability, and physical and mechanical properties was carried out. The results revealed that the use of 10 to 15% of MW improves mechanical performance, with increases from 17 to 26 kJ/m2, 14 to 17 MPa, and 794 to 1522 GPa in impact strength, tensile strength, and elastic modulus, respectively. By introducing a 20% MW filler, the composite loses its performance, particularly Shore D hardness, and becomes very brittle. Thermogravimetric analysis (TGA) indicated significant thermal stabilization, with a delay in the start decomposition temperature of 28 °C for 20 UPR/MW compared to 0 UPR/MW. Additionally, morphological and microstructural tests, namely, FT-IR, XRD, and SEM analysis, show a microstructural change, including the formation of crystalline phases, enhancing matrix-filler interactions due to the creation of Mg-O and Ca-O chemical bonds and the forming of filler agglomeration at high introduction rates that lead to defects in the microstructure. These results confirmed the mechanical results of the UPR/MW composites.
Open AccessAssessment of Mechanical Behavior and Microstructure of Unsaturated Polyester Resin Composites Reinforced with Recycled Marble Waste
The quarrying and utilization of natural stones such as marble and granite are growing rapidly in developing countries. However, the processing, cutting, sizing, and shaping of these stones to render them functional generates huge quantities of waste and dust. These materials are often disposed of openly in the environment, and their potentially hazardous nature has negative repercussions on both the environment and human health. In this study, marble waste (MW) was used as a filler in the unsaturated polyester resin (UPR) matrix to enhance performance and characteristics while adding value to the waste and minimizing manufacturing costs. For this purpose, samples of UPR/MW composites were produced with 0, 5, 10, 15, and 20 wt.% of MW incorporated into the UPR. A full characterization that focused on the microstructure, thermal stability, and physical and mechanical properties was carried out. The results revealed that the use of 10 to 15% of MW improves mechanical performance, with increases from 17 to 26 kJ/m2, 14 to 17 MPa, and 794 to 1522 GPa in impact strength, tensile strength, and elastic modulus, respectively. By introducing a 20% MW filler, the composite loses its performance, particularly Shore D hardness, and becomes very brittle. Thermogravimetric analysis (TGA) indicated significant thermal stabilization, with a delay in the start decomposition temperature of 28 °C for 20 UPR/MW compared to 0 UPR/MW. Additionally, morphological and microstructural tests, namely, FT-IR, XRD, and SEM analysis, show a microstructural change, including the formation of crystalline phases, enhancing matrix-filler interactions due to the creation of Mg-O and Ca-O chemical bonds and the forming of filler agglomeration at high introduction rates that lead to defects in the microstructure. These results confirmed the mechanical results of the UPR/MW composites.
- 29 October 2020
- Published by Taylor & Francis in European Journal of Environmental and Civil Engineering
- Vol. 26 (9) , 4112-4129
Mechanical performance and corrosion resistance of reinforced concrete with marble waste
In this work, the performance of reinforced concrete containing different percentages of marble filler as a partial substitution of ordinary Portland cement is investigated. The cement is replaced by marble accordingly in the range of 5, 10, 15 and 20 wt.% for concrete. The measurements of flexural and compressive strengths are conducted on the concrete with marble dust. The corrosion behaviour of reinforced concrete in the aggressive medium (3% NaCl) is carried out using the potentiodynamic polarisation and impedance spectroscopy. From the outcome of this investigation, the partial substitution of cement by up to 20% of marble in concrete is achieved without compromising the overall strength. For all mixtures, the maximum compressive and flexural strengths at all curing ages are obtained with a 5% replacement of cement by marble. The greater effectiveness of marble waste is attributed to its higher calcium content and CO32– ions release, which lead to the formation of carboaluminate hydrates, then to further porosity reduction that increases the strengths. The results also show that the steel bars in reinforced concrete prepared with 5% of marble have better corrosion to that in the ordinary reinforced concrete.
- 29 October 2020
- Published by Taylor & Francis in European Journal of Environmental and Civil Engineering
- Vol. 26 (9) , 4112-4129
Mechanical performance and corrosion resistance of reinforced concrete with marble waste
In this work, the performance of reinforced concrete containing different percentages of marble filler as a partial substitution of ordinary Portland cement is investigated. The cement is replaced by marble accordingly in the range of 5, 10, 15 and 20 wt.% for concrete. The measurements of flexural and compressive strengths are conducted on the concrete with marble dust. The corrosion behaviour of reinforced concrete in the aggressive medium (3% NaCl) is carried out using the potentiodynamic polarisation and impedance spectroscopy. From the outcome of this investigation, the partial substitution of cement by up to 20% of marble in concrete is achieved without compromising the overall strength. For all mixtures, the maximum compressive and flexural strengths at all curing ages are obtained with a 5% replacement of cement by marble. The greater effectiveness of marble waste is attributed to its higher calcium content and CO32– ions release, which lead to the formation of carboaluminate hydrates, then to further porosity reduction that increases the strengths. The results also show that the steel bars in reinforced concrete prepared with 5% of marble have better corrosion to that in the ordinary reinforced concrete.