Aiman Ismail
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Aiman Ismail has a total of 34 co-authors. Here are the top co-authors by number of shared publications:
- Fairuz Abdullah
Institute of Power Engineering, Universiti Tenaga Nasional, Kajang, Malaysia
9 shared publications - Md Zaini Jamaludin
Universiti Tenaga Nasional
6 shared publications - Abdul Hadi Sulaiman
Universiti Tenaga Nasional
5 shared publications - Nelidya Md Yusoff
Universiti Teknologi Malaysia Kuala Lumpur
3 shared publications - Nurul Asyikin Mohamed Radzi
Institute of Power Engineering, Universiti Tenaga Nasional, Kajang, Malaysia
3 shared publications - Allen Paul David
Razak Faculty of Technology and Informatics, Universiti Teknologi Malaysia Kuala Lumpur, Jalan Sultan Yahya Petra, 54100 Kuala Lumpur, Malaysia
2 shared publications
Latest Publications
- Open Access
- 24 May 2026
- Published by Universitas Negeri Padang in Teknomekanik
- Vol. 9 (2) , 238-255
Performance evaluation of a standalone PCA-based denoising method for Distributed Acoustic Sensing (DAS) data
This paper experimentally evaluates the effectiveness of Principal Component Analysis (PCA) for denoising distributed acoustic sensing (DAS) data. Experiments were conducted by applying different vibration strengths using a piezo-electric transducer (PZT) at various sensing locations along the sensing fiber. Unlike existing hybrid PCA-based DAS denoising approaches, this work explicitly investigates PCA as a standalone denoising framework, addressing the lack of systematic evaluation of its effectiveness and practical applicability. Results show that PCA improves the signal-to-noise ratio (SNR) by at least 4.7 dB across a range of strain levels. The SNR also shows improvements exceeding 5 dB for sensing fiber lengths up to ~5.2 km. For ~10.2 km vibration location, PCA still achieved around 2.45 dB of SNR improvement. The PCA algorithm was then compared with traditional denoising algorithms, i.e., Moving Average, Low-Pass Filtering, and Wavelet Denoising, at a fixed sensing fiber length of 3.2 km and 2 Vpp applied to the PZT. PCA outperformed these approaches in noise reduction while maintaining moderate computational cost. Overall, PCA effectively suppresses background noise while preserving the integrity of the vibration signal. These results indicate that standalone PCA is a practical denoising option for DAS applications that require improved SNR at a moderate processing cost.
- 24 May 2026
- Published by Universitas Negeri Padang in Teknomekanik
- Vol. 9 (2) , 238-255
Open AccessPerformance evaluation of a standalone PCA-based denoising method for Distributed Acoustic Sensing (DAS) data
This paper experimentally evaluates the effectiveness of Principal Component Analysis (PCA) for denoising distributed acoustic sensing (DAS) data. Experiments were conducted by applying different vibration strengths using a piezo-electric transducer (PZT) at various sensing locations along the sensing fiber. Unlike existing hybrid PCA-based DAS denoising approaches, this work explicitly investigates PCA as a standalone denoising framework, addressing the lack of systematic evaluation of its effectiveness and practical applicability. Results show that PCA improves the signal-to-noise ratio (SNR) by at least 4.7 dB across a range of strain levels. The SNR also shows improvements exceeding 5 dB for sensing fiber lengths up to ~5.2 km. For ~10.2 km vibration location, PCA still achieved around 2.45 dB of SNR improvement. The PCA algorithm was then compared with traditional denoising algorithms, i.e., Moving Average, Low-Pass Filtering, and Wavelet Denoising, at a fixed sensing fiber length of 3.2 km and 2 Vpp applied to the PZT. PCA outperformed these approaches in noise reduction while maintaining moderate computational cost. Overall, PCA effectively suppresses background noise while preserving the integrity of the vibration signal. These results indicate that standalone PCA is a practical denoising option for DAS applications that require improved SNR at a moderate processing cost.
- 5 February 2024
- Published by Optica Publishing Group in Applied Optics
- Vol. 63 (5) , 1241-1246
Sagnac-interferometer-based multiwavelength SOA fiber laser assisted by an intensity-dependent loss mechanism
We demonstrate a Sagnac-interferometer-based multiwavelength fiber laser with an intensity-dependent loss (IDL) mechanism in the L-band region using a semiconductor optical amplifier (SOA) as the gain medium. The IDL mechanism flattens and stabilizes the multiwavelength spectrum. We also investigate the effect of rotation angles of polarization controllers (PCs) at different polarization devices on multiwavelength performance. At best settings, 31 lasing lines within 3 dB uniformity were generated with an extinction ratio (ER) of 17 dB. Adjusting the half-wave plate of PC1 and PC2 from 0° to 90° shifted the multiwavelength output by 0.01 nm and 0.072 nm, respectively. PC2 adjustment also affects the multiwavelength flatness as compared to PC1. Furthermore, the number of lasing lines and the ER were directly influenced by the SOA current.
- 5 February 2024
- Published by Optica Publishing Group in Applied Optics
- Vol. 63 (5) , 1241-1246
Sagnac-interferometer-based multiwavelength SOA fiber laser assisted by an intensity-dependent loss mechanism
We demonstrate a Sagnac-interferometer-based multiwavelength fiber laser with an intensity-dependent loss (IDL) mechanism in the L-band region using a semiconductor optical amplifier (SOA) as the gain medium. The IDL mechanism flattens and stabilizes the multiwavelength spectrum. We also investigate the effect of rotation angles of polarization controllers (PCs) at different polarization devices on multiwavelength performance. At best settings, 31 lasing lines within 3 dB uniformity were generated with an extinction ratio (ER) of 17 dB. Adjusting the half-wave plate of PC1 and PC2 from 0° to 90° shifted the multiwavelength output by 0.01 nm and 0.072 nm, respectively. PC2 adjustment also affects the multiwavelength flatness as compared to PC1. Furthermore, the number of lasing lines and the ER were directly influenced by the SOA current.
- Open Access
- 4 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 110724-110735
Selecting Communication Technologies for an Electrical Substation Based on the AHP
Traditional communication technologies for distribution substations will soon have difficulties meeting the needs of emerging applications. This is due to exponential population growth and future energy demands, which necessitate a reliable and fast response from the grid. Thus, this research aims to aid decision-makers in selecting the best communication technologies for an electrical distribution substation. In this study, the Analytical Hierarchy Process (AHP) is used to shortlist, rank, and decide the most suitable communication technologies for an electrical substation based on its geographical location. The main criteria used for the selection are technical criteria, economic criteria, infrastructure, and service standards. The weight obtained from the pairwise comparison for each criterion is based on the literature review and expert opinions. The results comprise rankings of communication technologies tailored to different demographic settings, including urban, suburban, and rural areas. These rankings are generated through a comprehensive pairwise comparison process, building upon the earlier comparative analysis. Additionally, a structured framework has been developed to select the most appropriate communication technology for electrical substations in urban, suburban, and rural areas.
- 4 October 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 11, 110724-110735
Open AccessSelecting Communication Technologies for an Electrical Substation Based on the AHP
Traditional communication technologies for distribution substations will soon have difficulties meeting the needs of emerging applications. This is due to exponential population growth and future energy demands, which necessitate a reliable and fast response from the grid. Thus, this research aims to aid decision-makers in selecting the best communication technologies for an electrical distribution substation. In this study, the Analytical Hierarchy Process (AHP) is used to shortlist, rank, and decide the most suitable communication technologies for an electrical substation based on its geographical location. The main criteria used for the selection are technical criteria, economic criteria, infrastructure, and service standards. The weight obtained from the pairwise comparison for each criterion is based on the literature review and expert opinions. The results comprise rankings of communication technologies tailored to different demographic settings, including urban, suburban, and rural areas. These rankings are generated through a comprehensive pairwise comparison process, building upon the earlier comparative analysis. Additionally, a structured framework has been developed to select the most appropriate communication technology for electrical substations in urban, suburban, and rural areas.
- 22 August 2023
- Published by IOP Publishing in Physica Scripta
- Vol. 98 (9) , 095023
Effect of Rayleigh backscattering on the multiwavelength random fiber laser bandwidth
We investigated the effect of Rayleigh backscattering on the bandwidth of a multiwavelength random fiber laser (MWRFL). This MWRFL is based on an erbium-doped fiber amplifier (EDFA) as the gain medium and a Lyot filter as the wavelength-selective device. A high number and stable lasing line is generated with the assistance of a nonlinear polarization rotation effect induced by highly nonlinear fiber (HNLF) and optimized by a polarization controller. Longer single-mode fiber (SMF) produces wider multiwavelength bandwidth as compared to shorter SMF lengths, as 10 km, 3 km, and 0.1 km obtained 6.24 nm, 5.76 nm, and 2.75 nm wavelength bandwidth, respectively. When the SMF is removed from the setup, no Rayleigh backscattering is provided in the cavity, which led to a narrower multiwavelength bandwidth of 2.69 nm. Subsequently, the alteration of EDFA power, half-wave plate (HWP) angle, and quarter-wave plate (QWP) angles affected the degradation of multiwavelength performance. The best output spectrum is achieved at an EDFA power of 18 dBm, a HWP angle of 60°, and a QWP angle of 105°. The laser stability over a period of 120 min was excellent with a peak power deviation of 1.33 dB.
- 22 August 2023
- Published by IOP Publishing in Physica Scripta
- Vol. 98 (9) , 095023
Effect of Rayleigh backscattering on the multiwavelength random fiber laser bandwidth
We investigated the effect of Rayleigh backscattering on the bandwidth of a multiwavelength random fiber laser (MWRFL). This MWRFL is based on an erbium-doped fiber amplifier (EDFA) as the gain medium and a Lyot filter as the wavelength-selective device. A high number and stable lasing line is generated with the assistance of a nonlinear polarization rotation effect induced by highly nonlinear fiber (HNLF) and optimized by a polarization controller. Longer single-mode fiber (SMF) produces wider multiwavelength bandwidth as compared to shorter SMF lengths, as 10 km, 3 km, and 0.1 km obtained 6.24 nm, 5.76 nm, and 2.75 nm wavelength bandwidth, respectively. When the SMF is removed from the setup, no Rayleigh backscattering is provided in the cavity, which led to a narrower multiwavelength bandwidth of 2.69 nm. Subsequently, the alteration of EDFA power, half-wave plate (HWP) angle, and quarter-wave plate (QWP) angles affected the degradation of multiwavelength performance. The best output spectrum is achieved at an EDFA power of 18 dBm, a HWP angle of 60°, and a QWP angle of 105°. The laser stability over a period of 120 min was excellent with a peak power deviation of 1.33 dB.
- 15 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 425-428
Flatness Investigation of Multiwavelength SOA Random Fiber Laser Based on Sagnac Loop Mirror
We investigated the lasing performance of multiwavelength random fiber laser (MWRFL) at different single-mode fibers (SMFs). The main investigation is based on 700 m SMF with the presence of highly nonlinear fiber (HNLF) and polarizer as the current of the SOA is set to the maximum which is at 900 mA. With the assistance of the nonlinear polarization rotation (NPR) effect, two simultaneous multiwavelength spectra are generated, centered at 1575 nm and 1603 nm with multiwavelength bandwidth of 12 nm and 5 nm and 60 and 27 lines within 3 dB of bandwidth, respectively. The next investigations are based on 10 km and 300 m of SMF and without HNLF and polarizer from the setup, resulting in increased fluctuations and instability when a shorter 8-m of polarization-maintained fiber (PMF) is used. When the PMF length is changed to 42 m, the flatness is improved. The combination of specific fiber types with lengths such as SMF, PMF, and HNLF along with the polarizer influences the lasing lines and stability for the output of MWRFL.
- 15 August 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 425-428
Flatness Investigation of Multiwavelength SOA Random Fiber Laser Based on Sagnac Loop Mirror
We investigated the lasing performance of multiwavelength random fiber laser (MWRFL) at different single-mode fibers (SMFs). The main investigation is based on 700 m SMF with the presence of highly nonlinear fiber (HNLF) and polarizer as the current of the SOA is set to the maximum which is at 900 mA. With the assistance of the nonlinear polarization rotation (NPR) effect, two simultaneous multiwavelength spectra are generated, centered at 1575 nm and 1603 nm with multiwavelength bandwidth of 12 nm and 5 nm and 60 and 27 lines within 3 dB of bandwidth, respectively. The next investigations are based on 10 km and 300 m of SMF and without HNLF and polarizer from the setup, resulting in increased fluctuations and instability when a shorter 8-m of polarization-maintained fiber (PMF) is used. When the PMF length is changed to 42 m, the flatness is improved. The combination of specific fiber types with lengths such as SMF, PMF, and HNLF along with the polarizer influences the lasing lines and stability for the output of MWRFL.
- Open Access
- 12 August 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 113850-113865
5G New Radio: Dynamic Time Division Duplex Radio Resource Management Approaches
The Internet of Everything is currently in demand and has burdened the network tremendously. Accommodating this exponential increase in demand will require improved Radio Resource Management technology. This problem can be curbed with higher spectrum bands, reevaluation of Time Division Duplex, deployment of Software Defined Network, and Network Function Virtualization into 5G New Radio (NR) network. Therefore, this work aims to provide an in-depth survey on the recent resource management schemes that can be proposed for 5G NR enhancement by exploiting both rule-based algorithms and machine learning methods. Radio resource management consists of managing user allocation, the antenna transmission power, bandwidth, and modulation scheme. Therefore, in this paper, three categories of radio resource management technologies are introduced: resource allocation, energy efficiency, and interference management. The discussion revolves around their potentials and contributions as well as challenges faced to produce efficient 5G resource management schemes.
- 12 August 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 9, 113850-113865
Open Access5G New Radio: Dynamic Time Division Duplex Radio Resource Management Approaches
The Internet of Everything is currently in demand and has burdened the network tremendously. Accommodating this exponential increase in demand will require improved Radio Resource Management technology. This problem can be curbed with higher spectrum bands, reevaluation of Time Division Duplex, deployment of Software Defined Network, and Network Function Virtualization into 5G New Radio (NR) network. Therefore, this work aims to provide an in-depth survey on the recent resource management schemes that can be proposed for 5G NR enhancement by exploiting both rule-based algorithms and machine learning methods. Radio resource management consists of managing user allocation, the antenna transmission power, bandwidth, and modulation scheme. Therefore, in this paper, three categories of radio resource management technologies are introduced: resource allocation, energy efficiency, and interference management. The discussion revolves around their potentials and contributions as well as challenges faced to produce efficient 5G resource management schemes.
- Open Access
- 15 July 2021
- Published by Pertubuhan Ikatan Ilmuwan Nasional in Jurnal OptoElektronik
Nonlinearity Effect on Multiwavelength fiber laser based on Sagnac loop mirror interferometer
This paper demonstrates a multiwavelength fiber laser (MWFL) with erbiumdoped fiber amplifier (EDFA) as gain medium and Sagnac loop mirror interferometer as filter. Stable and flat lasing spectrum was achieved when highly nonlinear fiber (HNLF) was inserted into the laser cavity. The number of lasing lines and extinction ratio (ER) was directly influenced by EDFA gain where at maximum setting, 14 lasing lines with ER of 19 dB were generated. The stable and flat spectrum achieved spanned about 1.6 nm. This is due to the induced intensity dependent loss mechanism in the cavity by adjusting the half-wave plate of the polarization controller in combination with the HNLF. The MWFL output showed peak power variation of about 2.1 dB within 100 minutes of observation time.
- 15 July 2021
- Published by Pertubuhan Ikatan Ilmuwan Nasional in Jurnal OptoElektronik
Open AccessNonlinearity Effect on Multiwavelength fiber laser based on Sagnac loop mirror interferometer
This paper demonstrates a multiwavelength fiber laser (MWFL) with erbiumdoped fiber amplifier (EDFA) as gain medium and Sagnac loop mirror interferometer as filter. Stable and flat lasing spectrum was achieved when highly nonlinear fiber (HNLF) was inserted into the laser cavity. The number of lasing lines and extinction ratio (ER) was directly influenced by EDFA gain where at maximum setting, 14 lasing lines with ER of 19 dB were generated. The stable and flat spectrum achieved spanned about 1.6 nm. This is due to the induced intensity dependent loss mechanism in the cavity by adjusting the half-wave plate of the polarization controller in combination with the HNLF. The MWFL output showed peak power variation of about 2.1 dB within 100 minutes of observation time.
- 1 July 2021
- Published by Elsevier in Optical Fiber Technology
- Vol. 64
Tunable C + L bands triple frequency spacing multi-wavelength Brillouin-erbium fiber laser
- 1 July 2021
- Published by Elsevier in Optical Fiber Technology
- Vol. 64
Tunable C + L bands triple frequency spacing multi-wavelength Brillouin-erbium fiber laser
- 1 May 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 30-31
Raspberry Pi as Reconfigurable Fiber-based Router and Its Performance Analysis
Passive Optical Network (PON) has evolved drastically in order to provide greater speed and better reliability such as Next Generation PON1 (NG-PON1) and NG-PON2 which able to provide more than 40 Gbps and 128 Gbps of bandwidth respectively. Due to rapid growth of PON technologies, researchers have conducted many thorough experiments in order to enhance current PON-base technologies in a form of testbeds. However, most of the studies show that the testbeds have limitations either on its configurability, compactness or cost-efficiency. Hence, this motivates us to propose a lab-scale router testbed in PON architecture by using Raspberry Pi for its promising features and size. The experiments were done in a lab-scale area because the proposed router testbed is to provide a proof-of-concept solution of a reconfigurability router in PON. The results of the experiments are in terms of throughput, end-to-end delay and jitter for both downstream and upstream transmissions. After conducting the experiments, we have come to a conclusion that Raspberry Pis are suitable to be used as lab-scale routers in fiber networking architectures due to their reconfigurability, open source kernel, space-friendly and cost-efficient.
- 1 May 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 30-31
Raspberry Pi as Reconfigurable Fiber-based Router and Its Performance Analysis
Passive Optical Network (PON) has evolved drastically in order to provide greater speed and better reliability such as Next Generation PON1 (NG-PON1) and NG-PON2 which able to provide more than 40 Gbps and 128 Gbps of bandwidth respectively. Due to rapid growth of PON technologies, researchers have conducted many thorough experiments in order to enhance current PON-base technologies in a form of testbeds. However, most of the studies show that the testbeds have limitations either on its configurability, compactness or cost-efficiency. Hence, this motivates us to propose a lab-scale router testbed in PON architecture by using Raspberry Pi for its promising features and size. The experiments were done in a lab-scale area because the proposed router testbed is to provide a proof-of-concept solution of a reconfigurability router in PON. The results of the experiments are in terms of throughput, end-to-end delay and jitter for both downstream and upstream transmissions. After conducting the experiments, we have come to a conclusion that Raspberry Pis are suitable to be used as lab-scale routers in fiber networking architectures due to their reconfigurability, open source kernel, space-friendly and cost-efficient.