Abhilasha Kamboj
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Abhilasha Kamboj has a total of 50 co-authors. Here are the top co-authors by number of shared publications:
- Daniel Wasserman
University of Texas at Austin
9 shared publications - Aaron J. Muhowski
Sandia National Laboratories 2 , Albuquerque, New Mexico 87185
5 shared publications - Leland Nordin
University of Central Florida
5 shared publications - Noah C. Mansfield
The Chandra Family Department of Electrical and Computer Engineering, University of Texas at Austin 1 , Austin, Texas 78758
3 shared publications David Woolf
Physical Sciences Inc., Andover, MA, USA
2 shared publications- Jamie D. Phillips
Department of Electrical and Computer Engineering, University of Delaware, Newark, DE, USA
2 shared publications
Latest Publications
- 7 July 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 127 (1)
Dilute bismuth incorporated InGaBiAs photodetectors for extended short-wave infrared detection
Dilute bismuth (Bi) incorporated InGaBiAs is a promising material for an extended range of short-wave infrared (e-SWIR, 1.7–2.5 μm wavelength) detection. The InGaBiAs is a highly mismatched semiconductor alloy, where small concentrations of Bi incorporation alter the electronic band structure due to the valence band anti-crossing interaction between Bi states and host InGaAs material, resulting in a decrease in the bandgap energy. In this work, photodetectors based on InGaBiAs alloys lattice matched to InP demonstrate an extension of the cutoff wavelength beyond 2 μm. Dark current density, minority carrier lifetime, and responsivity strongly depend on group-V arsenic overpressure during epitaxial growth. Photodetectors grown under high arsenic flux pressure show low dark current values at room temperature (1.0 × 10−3 A/cm2 at 100 mV reverse bias), an order of magnitude lower than stoichiometric and low As flux grown devices, and correspondingly higher lifetime and responsivity. Two distinct activation energies were identified for each growth condition based on temperature-dependent dark current analysis, with trap-assisted generation-recombination in the depletion region and shallow defect recombination as the dark current-limiting factors in all devices.
- 7 July 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 127 (1)
Dilute bismuth incorporated InGaBiAs photodetectors for extended short-wave infrared detection
Dilute bismuth (Bi) incorporated InGaBiAs is a promising material for an extended range of short-wave infrared (e-SWIR, 1.7–2.5 μm wavelength) detection. The InGaBiAs is a highly mismatched semiconductor alloy, where small concentrations of Bi incorporation alter the electronic band structure due to the valence band anti-crossing interaction between Bi states and host InGaAs material, resulting in a decrease in the bandgap energy. In this work, photodetectors based on InGaBiAs alloys lattice matched to InP demonstrate an extension of the cutoff wavelength beyond 2 μm. Dark current density, minority carrier lifetime, and responsivity strongly depend on group-V arsenic overpressure during epitaxial growth. Photodetectors grown under high arsenic flux pressure show low dark current values at room temperature (1.0 × 10−3 A/cm2 at 100 mV reverse bias), an order of magnitude lower than stoichiometric and low As flux grown devices, and correspondingly higher lifetime and responsivity. Two distinct activation energies were identified for each growth condition based on temperature-dependent dark current analysis, with trap-assisted generation-recombination in the depletion region and shallow defect recombination as the dark current-limiting factors in all devices.
- 21 October 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 125 (17)
Room temperature mid-wave infrared guided mode resonance InAsSb photodetectors
We demonstrate room temperature operation of mid-wave infrared photodetectors leveraging a guided mode resonance architecture and bulk alloy InAsSb absorbers. Room temperature operation with low dark current is achieved by using detector structures with ultra-thin (150, 250 nm) absorbers leveraging the strong confinement enabled by the guided mode architecture. Devices with 1D and 2D grating arrays are fabricated and characterized, and compared to unpatterned detector devices. We see enhancement in the detectors’ optical response associated with coupling to both TE- and TM-polarized guided modes and good agreement between experimental and theoretically-predicted behavior. We show strong enhancement for unpolarized light incident on 2D grating arrays, with a broader spectral response than observed for polarized light incident upon 1D grating GMR detectors. The bulk InAsSb detectors presented in this work offer enhanced performance at room temperature for a range of imaging and sensing applications.
- 21 October 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 125 (17)
Room temperature mid-wave infrared guided mode resonance InAsSb photodetectors
We demonstrate room temperature operation of mid-wave infrared photodetectors leveraging a guided mode resonance architecture and bulk alloy InAsSb absorbers. Room temperature operation with low dark current is achieved by using detector structures with ultra-thin (150, 250 nm) absorbers leveraging the strong confinement enabled by the guided mode architecture. Devices with 1D and 2D grating arrays are fabricated and characterized, and compared to unpatterned detector devices. We see enhancement in the detectors’ optical response associated with coupling to both TE- and TM-polarized guided modes and good agreement between experimental and theoretically-predicted behavior. We show strong enhancement for unpolarized light incident on 2D grating arrays, with a broader spectral response than observed for polarized light incident upon 1D grating GMR detectors. The bulk InAsSb detectors presented in this work offer enhanced performance at room temperature for a range of imaging and sensing applications.
- 30 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 59 (4) , 1110-1122
A Sub-mm3 Wireless Neural Stimulator IC for Visual Cortical Prosthesis With Optical Power Harvesting and 7.5-kb/s Data Telemetry
This article proposes StiMote, an untethered, free-floating and individually addressable stimulator mote designed for visual cortex stimulation, aimed at vision restoration. The system is optically powered by a custom photovoltaic (PV) layer. In addition, the photodiode (PD) layer captures the light modulation and forwards it to the optical receiver (ORX) including a tranimpedance amplifier. Translated instructions can assign a unique slot, up to 1024 available, to each mote within the time-division multiple access (TDMA) framework. In this work, we propose an automatic charge balance (CB) technique that monitors the injected charge to balance in bi-phasic switched-capacitor stimulation (SCS). The chip was confirmed fully functional when operated completely wirelessly using harvested light. Measurement results revealed a power consumption of 4.48 $\mu$ W with a 7.5-kb/s optical downlink data rate, corresponding to continuous updates at 2.5 Hz of 1024 motes to their individual 3-b stimulation intensity levels. The dc–dc converter, responsible for providing high voltage for stimulation, demonstrated 4.3-V output voltage when unloaded, with a maximum efficiency of 67.4%. The proposed CB circuit exhibited linear controllability of stimulation charge up to 16 nC, with a charge imbalance of less than 0.2 nC. Furthermore, in vitro testing confirmed the absence of chemical reactions at electrodes, and in vivo experiments conducted on live rats verified the effectiveness of the stimulation through StiMote.
- 30 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 59 (4) , 1110-1122
A Sub-mm3 Wireless Neural Stimulator IC for Visual Cortical Prosthesis With Optical Power Harvesting and 7.5-kb/s Data Telemetry
This article proposes StiMote, an untethered, free-floating and individually addressable stimulator mote designed for visual cortex stimulation, aimed at vision restoration. The system is optically powered by a custom photovoltaic (PV) layer. In addition, the photodiode (PD) layer captures the light modulation and forwards it to the optical receiver (ORX) including a tranimpedance amplifier. Translated instructions can assign a unique slot, up to 1024 available, to each mote within the time-division multiple access (TDMA) framework. In this work, we propose an automatic charge balance (CB) technique that monitors the injected charge to balance in bi-phasic switched-capacitor stimulation (SCS). The chip was confirmed fully functional when operated completely wirelessly using harvested light. Measurement results revealed a power consumption of 4.48 $\mu$ W with a 7.5-kb/s optical downlink data rate, corresponding to continuous updates at 2.5 Hz of 1024 motes to their individual 3-b stimulation intensity levels. The dc–dc converter, responsible for providing high voltage for stimulation, demonstrated 4.3-V output voltage when unloaded, with a maximum efficiency of 67.4%. The proposed CB circuit exhibited linear controllability of stimulation charge up to 16 nC, with a charge imbalance of less than 0.2 nC. Furthermore, in vitro testing confirmed the absence of chemical reactions at electrodes, and in vivo experiments conducted on live rats verified the effectiveness of the stimulation through StiMote.
- Open Access
- 1 March 2023
- Published by AIP Publishing in APL Photonics
- Vol. 8 (3)
High-gain low-excess-noise MWIR detection with a 3.5-µm cutoff AlInAsSb-based separate absorption, charge, and multiplication avalanche photodiode
Mid-wavelength infrared detection is useful for a variety of scientific and military applications. Avalanche photodiodes can provide an advantage for detection as their internal gain mechanism can increase the system signal-to-noise ratio of a receiver. We demonstrate a separate absorption, charge, and multiplication avalanche photodiode using a digitally-grown narrow-bandgap Al0.05InAsSb absorber for MWIR detection and a wide bandgap Al0.7InAsSb multiplier for low-excess-noise amplification. Under 2-μm illumination at 100 K the device can reach gains over 850. The excess noise factor of the device scales with a low k-factor of ~0.04. The unity-gain external quantum efficiency of the device peaks at 54% (1.02 A/W) at 2.35 μm and maintains an efficiency of 24% (0.58 A/W) at 3 μm before cutting off at ~3.5 μm. At a gain of 850 the device has a gain-normalized dark current density of 0.05 mA/cm2. This device achieves gains more than double state-of-the-art InAs detectors and gain-normalized dark current densities over two orders of magnitude lower than a previously reported MWIR Al0.15InAsSb-based detector.
- 1 March 2023
- Published by AIP Publishing in APL Photonics
- Vol. 8 (3)
Open AccessHigh-gain low-excess-noise MWIR detection with a 3.5-µm cutoff AlInAsSb-based separate absorption, charge, and multiplication avalanche photodiode
Mid-wavelength infrared detection is useful for a variety of scientific and military applications. Avalanche photodiodes can provide an advantage for detection as their internal gain mechanism can increase the system signal-to-noise ratio of a receiver. We demonstrate a separate absorption, charge, and multiplication avalanche photodiode using a digitally-grown narrow-bandgap Al0.05InAsSb absorber for MWIR detection and a wide bandgap Al0.7InAsSb multiplier for low-excess-noise amplification. Under 2-μm illumination at 100 K the device can reach gains over 850. The excess noise factor of the device scales with a low k-factor of ~0.04. The unity-gain external quantum efficiency of the device peaks at 54% (1.02 A/W) at 2.35 μm and maintains an efficiency of 24% (0.58 A/W) at 3 μm before cutting off at ~3.5 μm. At a gain of 850 the device has a gain-normalized dark current density of 0.05 mA/cm2. This device achieves gains more than double state-of-the-art InAs detectors and gain-normalized dark current densities over two orders of magnitude lower than a previously reported MWIR Al0.15InAsSb-based detector.
- Open Access
- 9 January 2023
- Published by AIP Publishing in Applied Physics Letters
- Vol. 122 (2)
All-epitaxial resonant cavity enhanced long-wave infrared detectors for focal plane arrays
We demonstrate a monolithic all-epitaxial resonant-cavity architecture for long-wave infrared photodetectors with substrate-side illumination. An nBn detector with an ultra-thin (t≈350 nm) absorber layer is integrated into a leaky resonant cavity, formed using semi-transparent highly doped (n++) epitaxial layers, and aligned to the anti-node of the cavity's standing wave. The devices are characterized electrically and optically and demonstrate an external quantum efficiency of ∼25% at T=180 K in an architecture compatible with focal plane array configurations.
- 9 January 2023
- Published by AIP Publishing in Applied Physics Letters
- Vol. 122 (2)
Open AccessAll-epitaxial resonant cavity enhanced long-wave infrared detectors for focal plane arrays
We demonstrate a monolithic all-epitaxial resonant-cavity architecture for long-wave infrared photodetectors with substrate-side illumination. An nBn detector with an ultra-thin (t≈350 nm) absorber layer is integrated into a leaky resonant cavity, formed using semi-transparent highly doped (n++) epitaxial layers, and aligned to the anti-node of the cavity's standing wave. The devices are characterized electrically and optically and demonstrate an external quantum efficiency of ∼25% at T=180 K in an architecture compatible with focal plane array configurations.
- Open Access
- 26 December 2022
- Published by AIP Publishing in Applied Physics Letters
- Vol. 121 (26)
Mid-infrared rainbow light-emitting diodes
We demonstrate a room-temperature all-epitaxial guided-mode resonance light-emitting diode operating in the mid-wave infrared. The device comprises a dielectric waveguide with an AlGaAsSb p−i−n diode core, below a layer of grating-patterned GaSb and above a highly doped, and thus, low index, InAsSb layer. Light emitted from the device active region into propagating modes in the waveguide scatters into free space via the GaSb grating, giving rise to spectrally narrow features that shift with emission angle across much of the mid-wave infrared. For collection angles approaching 0°, we are able to obtain linewidths of ∼2.4 meV across the spectral/angular emission of the LED, corresponding to λ/Δλ∼570. Fine control of emission wavelength can be achieved by tuning the applied current, which causes a redshift of approximately 20 nm due to the thermo-optic effect. The presented device has the potential for use in compact, high bandwidth, and low-cost mid-wave infrared sensing applications requiring spectral discrimination.
- 26 December 2022
- Published by AIP Publishing in Applied Physics Letters
- Vol. 121 (26)
Open AccessMid-infrared rainbow light-emitting diodes
We demonstrate a room-temperature all-epitaxial guided-mode resonance light-emitting diode operating in the mid-wave infrared. The device comprises a dielectric waveguide with an AlGaAsSb p−i−n diode core, below a layer of grating-patterned GaSb and above a highly doped, and thus, low index, InAsSb layer. Light emitted from the device active region into propagating modes in the waveguide scatters into free space via the GaSb grating, giving rise to spectrally narrow features that shift with emission angle across much of the mid-wave infrared. For collection angles approaching 0°, we are able to obtain linewidths of ∼2.4 meV across the spectral/angular emission of the LED, corresponding to λ/Δλ∼570. Fine control of emission wavelength can be achieved by tuning the applied current, which causes a redshift of approximately 20 nm due to the thermo-optic effect. The presented device has the potential for use in compact, high bandwidth, and low-cost mid-wave infrared sensing applications requiring spectral discrimination.
- 13 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 34 (11) , 615-618
Room-Temperature Mid-Wave Infrared Guided-Mode Resonance Detectors
We demonstrate room temperature mid-wave infrared detectors with high peak detectivity. Our detector structures consist of type-II superlattice nBn detectors with ultra-thin ($\sim $ 250 nm) absorbers, integrated into an all-epitaxial guided-mode resonance architecture. The resulting devices show strong spectral selectivity, controlled by grating period, and low dark currents. We achieve room temperature$\vphantom {_{\int }}$ TE-polarized peak specific detectivity ($D^{*}$ ) of$\approx {1.2\times 10^{10}} \, {\text {cm}\sqrt {\text {Hz}}/\text {W}}$ at$\lambda = {4.4} \,{\mu }\text {m}$ and$\approx {1\times 10^{10}} \, {\text {cm}\sqrt {\text {Hz}}/W}$ at$\lambda = {4.7} \,{\mu }\text{m}$ , for grating periods of$\Lambda = {1.6} \, {\mu }\text{m}$ and$\Lambda ={1.8}\, {\mu }\text{m}$ , respectively. The presented all-epitaxial devices offer a unique approach to efficient room temperature mid-wave infrared detection with strong spectral and polarization selectivity.- 13 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Photonics Technology Letters
- Vol. 34 (11) , 615-618
Room-Temperature Mid-Wave Infrared Guided-Mode Resonance Detectors
We demonstrate room temperature mid-wave infrared detectors with high peak detectivity. Our detector structures consist of type-II superlattice nBn detectors with ultra-thin ($\sim $ 250 nm) absorbers, integrated into an all-epitaxial guided-mode resonance architecture. The resulting devices show strong spectral selectivity, controlled by grating period, and low dark currents. We achieve room temperature$\vphantom {_{\int }}$ TE-polarized peak specific detectivity ($D^{*}$ ) of$\approx {1.2\times 10^{10}} \, {\text {cm}\sqrt {\text {Hz}}/\text {W}}$ at$\lambda = {4.4} \,{\mu }\text {m}$ and$\approx {1\times 10^{10}} \, {\text {cm}\sqrt {\text {Hz}}/W}$ at$\lambda = {4.7} \,{\mu }\text{m}$ , for grating periods of$\Lambda = {1.6} \, {\mu }\text{m}$ and$\Lambda ={1.8}\, {\mu }\text{m}$ , respectively. The presented all-epitaxial devices offer a unique approach to efficient room temperature mid-wave infrared detection with strong spectral and polarization selectivity.- Open Access
- 3 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in TechRxiv
Room-Temperature Mid-Wave Infrared Guided-Mode Resonance Detectors
In this work, we report guided-mode resonance enhanced room-temperature mid-wave infrared photodetectors with significant spectral-selective enhancement in responsivity and detectivity, all in the absorber thickness of only 250 nm.
- 3 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in TechRxiv
Open AccessRoom-Temperature Mid-Wave Infrared Guided-Mode Resonance Detectors
In this work, we report guided-mode resonance enhanced room-temperature mid-wave infrared photodetectors with significant spectral-selective enhancement in responsivity and detectivity, all in the absorber thickness of only 250 nm.
- 28 January 2022
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 131 (4) , 043105
Cascaded InGaSb quantum dot mid-infrared LEDs
We demonstrate cascaded, mid-infrared light-emitting diodes with quantum dot based active regions. Cascading is achieved through highly reverse-biased AlInAsSb tunnel junctions that serve to connect the successive InGaSb quantum dot active regions. Temperature-dependent characterization of the output irradiance as a function of the current and voltage indicates that the cascade architecture has minimal leakage currents in contrast to earlier single-stage devices and provides carrier recycling with a concomitant increase in irradiance. The results show that cascaded architectures can be applied to quantum dot platforms and that the quantum efficiency of the active region limits the overall device efficiency.
- 28 January 2022
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 131 (4) , 043105
Cascaded InGaSb quantum dot mid-infrared LEDs
We demonstrate cascaded, mid-infrared light-emitting diodes with quantum dot based active regions. Cascading is achieved through highly reverse-biased AlInAsSb tunnel junctions that serve to connect the successive InGaSb quantum dot active regions. Temperature-dependent characterization of the output irradiance as a function of the current and voltage indicates that the cascade architecture has minimal leakage currents in contrast to earlier single-stage devices and provides carrier recycling with a concomitant increase in irradiance. The results show that cascaded architectures can be applied to quantum dot platforms and that the quantum efficiency of the active region limits the overall device efficiency.
- 17 May 2021
- Published by AIP Publishing in Applied Physics Letters
- Vol. 118 (20) , 201102
All-epitaxial guided-mode resonance mid-wave infrared detectors
We demonstrate all-epitaxial guided-mode resonance mid-wave infrared (MWIR) type-II superlattice nBn photodetectors. Our detectors consist of a high-index absorber/waveguide layer grown above a heavily doped ( ), and thus, low-index, semiconductor layer, and below a high-index and wide-bandgap grating-patterned layer. Polarization- and angle-dependent detector response is measured experimentally and simulated numerically, showing strongly enhanced absorption, compared to unpatterned detectors, at wavelengths associated with coupling to guided-mode resonances in our fabricated detectors. The detectors show high operating temperature (T = 200 K) external quantum efficiencies over 50% for TE-polarized light with absorber thickness of only 250 nm ( ). We calculate T = 200 K estimated specific detectivity for our detectors, on resonance, of , comparable with state-of-the-art MWIR detectors. The presented results offer an approach to monolithic, all-epitaxial integration of IR detector architectures with resonant optical cavities for enhanced detector response across the mid-wave infrared.- 17 May 2021
- Published by AIP Publishing in Applied Physics Letters
- Vol. 118 (20) , 201102
All-epitaxial guided-mode resonance mid-wave infrared detectors
We demonstrate all-epitaxial guided-mode resonance mid-wave infrared (MWIR) type-II superlattice nBn photodetectors. Our detectors consist of a high-index absorber/waveguide layer grown above a heavily doped ( ), and thus, low-index, semiconductor layer, and below a high-index and wide-bandgap grating-patterned layer. Polarization- and angle-dependent detector response is measured experimentally and simulated numerically, showing strongly enhanced absorption, compared to unpatterned detectors, at wavelengths associated with coupling to guided-mode resonances in our fabricated detectors. The detectors show high operating temperature (T = 200 K) external quantum efficiencies over 50% for TE-polarized light with absorber thickness of only 250 nm ( ). We calculate T = 200 K estimated specific detectivity for our detectors, on resonance, of , comparable with state-of-the-art MWIR detectors. The presented results offer an approach to monolithic, all-epitaxial integration of IR detector architectures with resonant optical cavities for enhanced detector response across the mid-wave infrared.