PVPavana Kumar Reddy Vennapusa

Pavana Kumar Reddy Vennapusa

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Pavana Kumar Reddy Vennapusa has a total of 19 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Seasonal Frost Penetration in Pavements with Multiple Layers

    by Yang Zhang, Robert Horton, David J. White, Pavana K. R. Vennapusa

    Seasonal freeze-thaw cycles and frost penetration depth in cold regions can be key contributors to pavement damage, and it is important as part of design practice to account for detrimental freeze-thaw conditions in the foundation layers. Empirical and numerical models have been developed to estimate frost penetration beneath pavements. This case study applies the modified Berggren equation as well as three simple empirical models to estimate frost penetration for multiple pavement conditions. Each of the test locations had an array of buried temperature sensors and different pavement structures. The simple empirical equations performed poorly, but the modified Berggren equation had more promising frost penetration depths. Modified Berggren equation calculations were performed with a computer program. The air and ground surface temperatures were monitored to verify influences of the n-factor transferring air to surface freezing index. Different geomaterial properties were used in calculations to explore ways to improve estimation accuracy. Results indicate that pavement type, foundation layer conditions, and local climate affect the computer program’s frost penetration estimates. Including site-specific information improves the accuracy of frost penetration predictions.


  • Investigating Frost Heave Deterioration at Pavement Joint Locations

    by Yang Zhang, David J. White, Pavana K. R. Vennapusa, Alex E. Johnson, Maxim M. Prokudin

    Frost heave of foundation materials causes severe joint deterioration in concrete pavements. Sufficient freezing depth, continuous water supply, and frost susceptible geomaterials are the three necessary factors leading to frost heave. To investigate the frost actions of deteriorated pavements with frost heaves at joint locations, the longitudinal pavement surface profiles were plotted by measuring vertical heaves crossing transverse joints. Specimens were cored to determine the moisture conditions at different layers. Ice lenses were found at layer interfaces, and frozen base layers with low permeability contributed to trapping water within joint spaces. Another objective of this study was to determine the local freeze-thaw conditions in pavements. Temperature sensors were installed during the reconstruction to estimate the frost penetration depths, lengths of freezing and thawing periods, and number of freeze-thaw cycles at different depths. Up to 1.1 m frost penetration depth was found, and it showed various lengths of freezing periods. The last objective was to evaluate the frost-heave and thaw-weakening susceptibility of the reconstructed foundation materials. Results indicated that all three geomaterials were medium frost-heave susceptible, and the soft subgrade showed high thaw-weakening susceptibility.


  • Comparison of Pavement Slab Stabilization Using Cementitious Grout and Injected Polyurethane Foam

    by Pavana K. R. Vennapusa, Yang Zhang, David J. White

    This paper reviews the current status of slab stabilization specifications and describes in situ test results and statistical analysis comparing injected polyurethane foam and cementitious grout for a deteriorating jointed concrete pavement supported on an open-graded aggregate subbase. The stabilization was performed to improve support conditions by filling voids, reducing deflections under loading, and improving load transfer efficiency (LTE) near joints and cracks. Falling weight deflectometer (FWD) tests and faulting measurements were obtained before and after stabilization. LTE measurements indicated statistically significant improvement near cracks and joints in both sections. Deflections under loading showed statistically significant improvements only near cracks (and not near joints) in the injected foam section and only near joints (and not near cracks) in the cementitious grout section. Faulting reduced by about 2–5 mm after injected foam stabilization and 1–2 mm after cementitious grout...


  • Application of Terrestrial Laser Scanning for the Displacement Monitoring of GRS-IBS Abutments

    by Ahmad Alhasan, Michael P. McGuire, Pavana K. R. Vennapusa, David J. White

    Bridge abutments constructed using geosynthetic-reinforced soil (GRS) with an integrated bridge system (IBS) are becoming increasingly popular because of cost efficiency and rapid construction. Monitoring the vertical and lateral deformations of the GRS-IBS facing is one technique that has been used to assess performance. The conventional approach is to measure vertical and lateral deformations using a standard survey level and rod. This paper describes lessons learned from the use of three-dimensional (3D) stationary terrestrial laser scanning (TLS) to measure facing displacements for a two lane 32 m long GRS-IBS constructed in Sheffield, MA. The intent was to measure displacement of the split-face segmental concrete block facing by comparing position measurements obtained before and after placement of the bridge deck on the abutments. A simple procedure is followed to analyze the point clouds. The high measurement density and resolution provided by the laser scanner enables detailed observation of how the abutments deform in response to the applied loads. The capability of the proposed procedure to measure displacement is discussed in the context of the displacements allowed in the current GRS-IBS design methodology.


  • Pavement thickness and stabilised foundation layer assessment using ground-coupled GPR

    by Jinhui Hu, Pavana K. R. Vennapusa, David J. White, Igor Beresnev

    Experimental results from field and laboratory investigations using a ground-coupled ground penetrating radar (GPR), dielectric measurement, magnetic imaging tomography (MIT) and dynamic cone penetrometer (DCP) tests are presented. Dielectric properties of asphalt pavement and stabilised and unstabilised pavement foundation materials were evaluated in the laboratory in frozen and unfrozen conditions. Laboratory test results showed that dielectric properties of materials back-calculated from GPR in comparison to dielectric gauge measurements are strongly correlated and repeatable. For chemically stabilised materials, curing time affected the dielectric properties of the materials. Field tests were conducted on asphalt pavement test sections with different foundation materials (stabilised and unstabilised layers), drainage conditions and layer thicknesses. GPR and MIT results were used to determine asphalt layer thicknesses and were compared with measured core thicknesses, while GPR and DCP were used to assess foundation layer profiles. Asphalt thicknesses estimated from GPR showed an average error of about 11% using the dielectric gauge values as input. The average error reduced to about 4% when calibrated with cores thicknesses. MIT results showed thicknesses that are about 9% higher than estimated using GPR. Foundation layer thicknesses could not be measured using GPR due to variations in moisture conditions between the test sections, which is partly attributed to variations in gradation and drainage characteristics of the subbase layer.


  • Road Map for Implementation of Intelligent Compaction Technology

    by David J. White, Pavana Vennapusa, Mark Dunn

    Over the past few years, intelligent compaction (IC) has been a focus of research, demonstration projects, and specification development in the United States. The Federal Highway Administration (FHWA) has recently moved IC to national level implementation. Equipment manufacturers, individual state DOTs, and the Technology Transfer for Intelligent Compaction Consortium (TTICC), a Transportation Pooled Fund, TPF-5(233) initiative, are also focusing on implementation efforts. What this paper does is describe the results of a series of workshops attended by more than 400 attendees—representing several state DOTs, FHWA, equipment manufacturers, and researchers—that contributed to a detailed roadmap identifying implementation needs and action items. A key outcome of these workshops was the development of a prioritized list initially created in 2008 and updated annually through 2012. This paper describes in greater detail how this list was developed and prioritized and how it has changed since it was initiated in 2008. Accompanying this list is a set of action items to overcome the various barriers identified.


  • Interpretation of Dual Roller-Integrated Compaction Measurements on Layered Granular Fill

    by Pavana K. R. Vennapusa, David J. White

    This paper presents findings from a field study conducted with a smooth drum vibratory roller equipped with machine drive power (MDP) and accelerometer-based compaction meter value (CMV) technologies. Two test sections with layered granular materials were mapped using the roller and tested using lightweight deflectometer (LWD) and dynamic cone penetrometer (DCP). One area consisted of a thin relatively stiff recycled asphalt material underlain by poorly graded fine sand, and the other test area consisted of compacted layers of poorly graded sand. Results indicated that the thin stiff layer in one of the test areas influenced the MDP and LWD measurements more than the CMV measurements. CMV showed deeper influence depths (up to 1 m) compared with MDP (< 0.5 m). MDP measurements correlated well with LWD and DCP-California bearing ratio (CBR) measurements when data from the top 300 mm was used. CMV correlated well with CBR measurements when data from the full profile (up to 800 mm) was used.


  • A Case Study of Geosynthetic-Reinforced Soil in a Low-Volume Bridge Abutment in Iowa

    by Pavana Kr. Vennapusa, David J. White, Brian Keierleber

    This paper presents findings from a case study conducted on a low-volume road bridge in Iowa, where geosynthetic-reinforced soil (GRS) was used as fill material in the reconstructed bridge abutments. The original steel bridge supported was on concrete abutments and was replaced with a longer railroad flat car bridge and spread footings founded on the GRS fill. The concrete abutments along with some of the existing fill were left in place to serve as GRS facing, and the soil under the new footing was excavated and replaced with GRS fill. The cost of constructing the bridge was about 60% lower than a conventional concrete bridge deck and abutments. Laboratory tests showed that samples reinforced with geosynthetic layers exhibit higher shear strength and lower permanent strain. When a static load was applied over the foundation with a loaded truck, horizontal stress increase was low along the excavation walls. Analysis indicated that the location of the water table and loading conditions influence the bearing capacity and global stability of the abutment system.

  • Rapid In Situ Measurement of Hydraulic Conductivity for Granular Pavement Foundations

    by David J. White, Pavana Vennapusa

    This paper describes the application of a relatively new rapid in situ test device for measuring the hydraulic conductivity of granular pavement foundation materials. The test device uses air as the permeating fluid with compensations for fluid viscosity and unsaturated flow conditions. Because the test device allows for rapid measurement, many tests can be performed in a short time, which allows for statistical analysis of the results. Three different sections surfaced with crushed limestone subbase material were tested in this study. These test sections varied in support conditions beneath the subbase layer with cement-stabilized subgrade, geogrid at the subbase/subbase interface, and compacted subgrade (control section with no stabilization). Control section showed relatively high hydraulic conductivity on average and low amount of spatial variation. Cement-stabilized subgrade section showed relatively low hydraulic conductivity on average, and the geogrid reinforced section showed relatively high amount of spatial variation. The variations observed in hydraulic conductivity are directly related to the segregation and degradation of the base material, which occurred due to differences in the support conditions beneath the subbase layer and traffic loading.


  • In situmechanistic characterisations of granular pavement foundation layers

    by Pavana Kumar Reddy Vennapusa, David J. White, John Siekmeier, Rebecca A. Embacher

    This paper presents experimental test results comparing in situ point test measurements using falling weight deflectometer (FWD), light weight deflectometer (LWD), dynamic cone penetrometer and static piezocone, and near continuous roller-integrated continuous compaction control measurements on a granular pavement foundation embankment. Piezoelectric earth pressure cells buried in the pavement foundation layers were used to compare vertical and horizontal stresses during vibratory roller compaction, and LWD and FWD impulse loading. The resulting total stress paths are compared with standard laboratory resilient modulus stress paths. Insights into differences in measurement influence depths and comparison of vertical stress profiles for the different measurements are discussed and relationships between the various measurements in terms of elastic modulus are presented. Some practical considerations for interpreting the relationships and implementation are discussed.