Stephane Ginestar
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Stephane Ginestar has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Jamal Zbitou
Abdelmalek Essaadi University
6 shared publications - Mohammed El Gibari
Nantes Université
6 shared publications - Fouad Aytouna
Abdelmalek Essaadi University
4 shared publications - Caroline Borderon
IETR, UMR CNRS 6164, Université de Nantes 2 , 44322 Nantes, France
3 shared publications - Hartmut W. Gundel
IETR, UMR CNRS 6164, Université de Nantes 2 , 44322 Nantes, France
3 shared publications - Kevin Nadaud
GREMAN UMR 7347 Université de Tours CNRS INSA-CVL 16 rue Pierre et Marie Curie 37071 Tours France
3 shared publications
Latest Publications
- Open Access
- 1 October 2026
- Published by Institute of Advanced Engineering and Science in Bulletin of Electrical Engineering and Informatics
- Vol. 15 (5) , 4014-4025
A compact flat antenna array based on Wilkinson power divider for radar applications
This paper presents the design, simulation, and achievement of an optimized 64-element antenna array based on Wilkinson power divider operating at 24 GHz. The whole circuit is mounted on a Rogers RO4830 substrate with a thickness of 0.127 mm, copper cladding thickness of 0.018 mm, dielectric constant of 3.24, and a loss tangent of 0.0033. Using advanced design system (ADS) from Keysight, the combiner is meticulously simulated to achieve efficient power combination with minimal insertion loss, excellent impedance matching, and high port-to-port isolation. The design ensures that power from multiple input ports is effectively combined into a single output port, suitable for high-frequency applications. Simulation results at 24 GHz confirm optimal performance, and validation corroborates the accuracy of the ADS-based simulations. The proposed design demonstrates reliability and efficiency for integration into modern communication radar systems operating at millimeter-wave frequencies.
- 1 October 2026
- Published by Institute of Advanced Engineering and Science in Bulletin of Electrical Engineering and Informatics
- Vol. 15 (5) , 4014-4025
Open AccessA compact flat antenna array based on Wilkinson power divider for radar applications
This paper presents the design, simulation, and achievement of an optimized 64-element antenna array based on Wilkinson power divider operating at 24 GHz. The whole circuit is mounted on a Rogers RO4830 substrate with a thickness of 0.127 mm, copper cladding thickness of 0.018 mm, dielectric constant of 3.24, and a loss tangent of 0.0033. Using advanced design system (ADS) from Keysight, the combiner is meticulously simulated to achieve efficient power combination with minimal insertion loss, excellent impedance matching, and high port-to-port isolation. The design ensures that power from multiple input ports is effectively combined into a single output port, suitable for high-frequency applications. Simulation results at 24 GHz confirm optimal performance, and validation corroborates the accuracy of the ADS-based simulations. The proposed design demonstrates reliability and efficiency for integration into modern communication radar systems operating at millimeter-wave frequencies.
- 30 September 2026
- Published by IOP Publishing in Engineering Research Express
- Vol. 8 (19) , 195316
A compact and highly-selective coplanar bandpass filter for ISM band applications
This research outlines the development of a compact and highly selective coplanar bandpass filter designed specifically for applications within the ISM band. The filter utilizes coplanar waveguide technology and is fabricated on a Rogers RT/duroid 5880 substrate, which has a thickness of 1.02mm, a dielectric constant of 2.2, and a minimal loss tangent of 0.0009. The design achieves a return loss exceeding 15 dB and an insertion loss of approximately 1.5dB, centered at a frequency of 2.5 GHz, with an operational bandwidth that spans from 2.29GHz to 2.68 GHz, yielding a total of 390MHz. Electromagnetic simulations performed using two different numerical techniques validate the low passband insertion loss and robust out-of-band rejection. To confirm these findings experimentally, a prototype was constructed, and its S-parameters were measured, revealing a strong correlation with the simulation results. The filter has a compact size of 19.7 ×22.05 mm 2 , making it ideal for use in wireless communication and radio frequency signal processing systems. Notably, the 2.4 GHz ISM band is widely utilized in various practical applications, including microwave ovens, Wi-Fi routers, and Bluetooth devices.
- 30 September 2026
- Published by IOP Publishing in Engineering Research Express
- Vol. 8 (19) , 195316
A compact and highly-selective coplanar bandpass filter for ISM band applications
This research outlines the development of a compact and highly selective coplanar bandpass filter designed specifically for applications within the ISM band. The filter utilizes coplanar waveguide technology and is fabricated on a Rogers RT/duroid 5880 substrate, which has a thickness of 1.02mm, a dielectric constant of 2.2, and a minimal loss tangent of 0.0009. The design achieves a return loss exceeding 15 dB and an insertion loss of approximately 1.5dB, centered at a frequency of 2.5 GHz, with an operational bandwidth that spans from 2.29GHz to 2.68 GHz, yielding a total of 390MHz. Electromagnetic simulations performed using two different numerical techniques validate the low passband insertion loss and robust out-of-band rejection. To confirm these findings experimentally, a prototype was constructed, and its S-parameters were measured, revealing a strong correlation with the simulation results. The filter has a compact size of 19.7 ×22.05 mm 2 , making it ideal for use in wireless communication and radio frequency signal processing systems. Notably, the 2.4 GHz ISM band is widely utilized in various practical applications, including microwave ovens, Wi-Fi routers, and Bluetooth devices.
- Open Access
- 1 September 2026
- Published by IOP Publishing in Journal of Instrumentation
- Vol. 21 (09) , P09030
Design and development of multi-section coupled-line couplers with reconfigurable capacitance for high-frequency operating at 24 GHz
This article presents a comparative study of three coupled-line couplers (CLC) designed to operate at a high frequency of 24 GHz, along with an investigation of a reconfigurable CLC. The couplers differ in the number of sections: the first CLC has one section, the second has two sections, and the third has three sections. The latter will be transformed into a reconfigurable coupler by adding capacitors at transmission line terminals. The performance of each design is evaluated according to key criteria, including reflection ( S 11 ), transmission ( S 12 ), coupling ( S 13 ), isolation ( S 14 ) and phase response. The simulation results showed that the single-section coupler provides moderate performance, with rather weak coupling, while the two-section coupler shows significant improvement, especially in coupling, which prompted us to add the third section, which gave the best performance, better improvement and good results on all S-parameters. Good isolation ( S 14 = -34.3 dB), reflection ( S 11 = -34 dB), transmission ( S 12 = -2.95 dB), coupling ( S 13 = -3.22 dB) and the phase difference between S 12 and S 13 is 90 deg, outperforming all previous single- and two-section configurations, which prompted us to develop this three-section CLC and make it adjustable over a wider range, so that it can be suitable for many applications. Simulations were performed using an Electromagnetic Solver (EM) based on Finite Integration Technique and advanced design system (ADS) solver based on Moments Method to evaluate the coupler behavior.
- 1 September 2026
- Published by IOP Publishing in Journal of Instrumentation
- Vol. 21 (09) , P09030
Open AccessDesign and development of multi-section coupled-line couplers with reconfigurable capacitance for high-frequency operating at 24 GHz
This article presents a comparative study of three coupled-line couplers (CLC) designed to operate at a high frequency of 24 GHz, along with an investigation of a reconfigurable CLC. The couplers differ in the number of sections: the first CLC has one section, the second has two sections, and the third has three sections. The latter will be transformed into a reconfigurable coupler by adding capacitors at transmission line terminals. The performance of each design is evaluated according to key criteria, including reflection ( S 11 ), transmission ( S 12 ), coupling ( S 13 ), isolation ( S 14 ) and phase response. The simulation results showed that the single-section coupler provides moderate performance, with rather weak coupling, while the two-section coupler shows significant improvement, especially in coupling, which prompted us to add the third section, which gave the best performance, better improvement and good results on all S-parameters. Good isolation ( S 14 = -34.3 dB), reflection ( S 11 = -34 dB), transmission ( S 12 = -2.95 dB), coupling ( S 13 = -3.22 dB) and the phase difference between S 12 and S 13 is 90 deg, outperforming all previous single- and two-section configurations, which prompted us to develop this three-section CLC and make it adjustable over a wider range, so that it can be suitable for many applications. Simulations were performed using an Electromagnetic Solver (EM) based on Finite Integration Technique and advanced design system (ADS) solver based on Moments Method to evaluate the coupler behavior.
- Open Access
- 1 August 2026
- Published by Institute of Advanced Engineering and Science in Bulletin of Electrical Engineering and Informatics
- Vol. 15 (4) , 3047-3057
A new compact printed ring bandpass filter structure for ISM band applications
We introduce a novel, compact bandpass filter (BPF) that employs Ring coupling through a microstrip design. This filter features a ring resonator that mainly relies on capacitive coupling to achieve its resonant characteristic. The results from experimental fabrication confirmed the expected performance of the filter, showing strong agreement between the simulated and measured S-parameters. The filter is built on a RO4003C substrate that is 1.52 mm thick, with a dielectric constant of 3.38 and a loss tangent of 0.0027. Designed for a center frequency of 5.72 GHz and a bandwidth of 930 MHz, it exhibits low insertion loss and effective signal rejection, as supported by advanced electromagnetic simulations. This flexible and efficient filter design represents a significant step forward, offering great potential for innovative communication systems and wireless power transmission, especially when integrated with 5.8 GHz straight-through antenna arrays for wireless energy harvesting.
- 1 August 2026
- Published by Institute of Advanced Engineering and Science in Bulletin of Electrical Engineering and Informatics
- Vol. 15 (4) , 3047-3057
Open AccessA new compact printed ring bandpass filter structure for ISM band applications
We introduce a novel, compact bandpass filter (BPF) that employs Ring coupling through a microstrip design. This filter features a ring resonator that mainly relies on capacitive coupling to achieve its resonant characteristic. The results from experimental fabrication confirmed the expected performance of the filter, showing strong agreement between the simulated and measured S-parameters. The filter is built on a RO4003C substrate that is 1.52 mm thick, with a dielectric constant of 3.38 and a loss tangent of 0.0027. Designed for a center frequency of 5.72 GHz and a bandwidth of 930 MHz, it exhibits low insertion loss and effective signal rejection, as supported by advanced electromagnetic simulations. This flexible and efficient filter design represents a significant step forward, offering great potential for innovative communication systems and wireless power transmission, especially when integrated with 5.8 GHz straight-through antenna arrays for wireless energy harvesting.
- 1 July 2026
- Published by IOP Publishing in Engineering Research Express
- Vol. 8 (13) , 135335
A novel compact microstrip structure of a reconfigurable coupled-line bandpass filter based on varactor diode agility
This work presents a reconfigurability study of a compact coupled-line bandpass filter (CL-BPF) through four successive design stages. The baseline CL-BPF, designed on a Rogers RT/duroid-5880 substrate, demonstrates excellent initial performance with a return loss ( S 11 ) of −25 dB and an insertion loss ( S 12 ) of −0.1 dB at the resonance frequency f 0 = 5.80 GHz , and a bandwidth of 800 MHz. Building upon this reference structure, a first reconfigurable stage was introduced by integrating four lumped capacitors, enabling a tuning window from 6.30 to 6.75 GHz for capacitances ranging between 0.7 and 1.5 pF, with a bandwidth varying between 100 and 300 MHz. The second configuration, which employs six capacitors, expands the tuning capability from 6.27 to 6.85 GHz as the capacitance varies from 0.5 to 1.5 pF, while maintaining a passband bandwidth from 130 to 320 MHz at each capacitance setting. Due to its superior tunability, the six-capacitor architecture was selected as the foundation for full electrical reconfigurability. In the final stage, the capacitors were replaced with SMV1405 varactor diodes whose capacitance range aligns well with the values of the passive design and a simplified biasing network was implemented. Two dedicated biasing networks are employed to control the varactor diodes, while both networks are supplied by a single DC voltage source. By adjusting the control voltage from 1 to 29 V, the proposed reconfigurable filter exhibits smooth and continuous frequency tuning from 6.65 to 7.40 GHz, while maintaining a nearly constant passband bandwidth ranging from 280 to 300 MHz across all tuning states. The design was validated through simulations performed in both solvers: an electromagnetic solver based on the finite integration technique and the advanced design system 2026 using the method of moments, where the excellent correlation between the results confirms the robustness and reliability of the proposed approach.
- 1 July 2026
- Published by IOP Publishing in Engineering Research Express
- Vol. 8 (13) , 135335
A novel compact microstrip structure of a reconfigurable coupled-line bandpass filter based on varactor diode agility
This work presents a reconfigurability study of a compact coupled-line bandpass filter (CL-BPF) through four successive design stages. The baseline CL-BPF, designed on a Rogers RT/duroid-5880 substrate, demonstrates excellent initial performance with a return loss ( S 11 ) of −25 dB and an insertion loss ( S 12 ) of −0.1 dB at the resonance frequency f 0 = 5.80 GHz , and a bandwidth of 800 MHz. Building upon this reference structure, a first reconfigurable stage was introduced by integrating four lumped capacitors, enabling a tuning window from 6.30 to 6.75 GHz for capacitances ranging between 0.7 and 1.5 pF, with a bandwidth varying between 100 and 300 MHz. The second configuration, which employs six capacitors, expands the tuning capability from 6.27 to 6.85 GHz as the capacitance varies from 0.5 to 1.5 pF, while maintaining a passband bandwidth from 130 to 320 MHz at each capacitance setting. Due to its superior tunability, the six-capacitor architecture was selected as the foundation for full electrical reconfigurability. In the final stage, the capacitors were replaced with SMV1405 varactor diodes whose capacitance range aligns well with the values of the passive design and a simplified biasing network was implemented. Two dedicated biasing networks are employed to control the varactor diodes, while both networks are supplied by a single DC voltage source. By adjusting the control voltage from 1 to 29 V, the proposed reconfigurable filter exhibits smooth and continuous frequency tuning from 6.65 to 7.40 GHz, while maintaining a nearly constant passband bandwidth ranging from 280 to 300 MHz across all tuning states. The design was validated through simulations performed in both solvers: an electromagnetic solver based on the finite integration technique and the advanced design system 2026 using the method of moments, where the excellent correlation between the results confirms the robustness and reliability of the proposed approach.
- 21 April 2026
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 44 (3)
In situ XPS investigation of β-Ga2O3 surface chemistry for the development of SF6/Ar based plasma atomic layer etching processes
Atomic layer etching (ALE) is promising approach for low-damage etching of β-Ga2O3, a key ultrawide bandgap semiconductor for next-generation electronic and optoelectronic devices. ALE offers nanometer-scale control over the etching process, enabling the fabrication of smooth surfaces and precise management of surface defect density. In this work, an SF6/Ar-based ALE process is investigated with a focus on plasma–surface interactions and surface chemical evolution. In situ x-ray photoelectron spectroscopy is used to monitor chemical changes after the modification and activation steps, while atomic force microscopy is used to evaluate surface morphology. The modification step is dominated by fluorine-based surface reactions, leading to the formation of stable Ga–F species and exhibiting an intrinsically self-limiting behavior. Material removal occurs during the activation step under Ar+ ion bombardment, where physical sputtering competes with fluorine redeposition. Insufficient activation results in fluorine accumulation and surface degradation, whereas optimized ion energy and activation time establish a stable surface composition and yield smooth, defect-free surfaces. These results highlight the critical role of plasma conditions in controlling ALE mechanisms and demonstrate the potential of fluorine-based ALE for controlled etching and surface smoothing of β-Ga2O3.
- 21 April 2026
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 44 (3)
In situ XPS investigation of β-Ga2O3 surface chemistry for the development of SF6/Ar based plasma atomic layer etching processes
Atomic layer etching (ALE) is promising approach for low-damage etching of β-Ga2O3, a key ultrawide bandgap semiconductor for next-generation electronic and optoelectronic devices. ALE offers nanometer-scale control over the etching process, enabling the fabrication of smooth surfaces and precise management of surface defect density. In this work, an SF6/Ar-based ALE process is investigated with a focus on plasma–surface interactions and surface chemical evolution. In situ x-ray photoelectron spectroscopy is used to monitor chemical changes after the modification and activation steps, while atomic force microscopy is used to evaluate surface morphology. The modification step is dominated by fluorine-based surface reactions, leading to the formation of stable Ga–F species and exhibiting an intrinsically self-limiting behavior. Material removal occurs during the activation step under Ar+ ion bombardment, where physical sputtering competes with fluorine redeposition. Insufficient activation results in fluorine accumulation and surface degradation, whereas optimized ion energy and activation time establish a stable surface composition and yield smooth, defect-free surfaces. These results highlight the critical role of plasma conditions in controlling ALE mechanisms and demonstrate the potential of fluorine-based ALE for controlled etching and surface smoothing of β-Ga2O3.
- Open Access
- 1 February 2026
- Published by Institute of Advanced Engineering and Science in Bulletin of Electrical Engineering and Informatics
- Vol. 15 (1) , 209-218
Design and fabrication of a novel millimeter-wave bandstop filter using transversal signal interference technique
This paper presents the design, simulation, and fabrication of a miniaturized millimeter-wave band-stop filter (BSF) on microstrip technology. The proposed arrangement is based on the concept of transversal interference of signals, and is realized as a pair of parallel transmission lines with the appropriate characteristic impedance and electrical length. Such scheme provides sharpening signal discrimination without resonator structures additional to the filter. The filter is fabricated on a ROGERS RT/Duroid 5880 substrate, selected for its favorable properties at high frequencies, including a thickness of 0.13 mm, a relative dielectric constant of 2.2, and a loss tangent of 0.0009. The optimized design was validated through electromagnetic simulations by two types of electromagnetic solvers, and then fabricated and measured by coplanar waveguide (CPW) probe to confirm its practical performance.
- 1 February 2026
- Published by Institute of Advanced Engineering and Science in Bulletin of Electrical Engineering and Informatics
- Vol. 15 (1) , 209-218
Open AccessDesign and fabrication of a novel millimeter-wave bandstop filter using transversal signal interference technique
This paper presents the design, simulation, and fabrication of a miniaturized millimeter-wave band-stop filter (BSF) on microstrip technology. The proposed arrangement is based on the concept of transversal interference of signals, and is realized as a pair of parallel transmission lines with the appropriate characteristic impedance and electrical length. Such scheme provides sharpening signal discrimination without resonator structures additional to the filter. The filter is fabricated on a ROGERS RT/Duroid 5880 substrate, selected for its favorable properties at high frequencies, including a thickness of 0.13 mm, a relative dielectric constant of 2.2, and a loss tangent of 0.0009. The optimized design was validated through electromagnetic simulations by two types of electromagnetic solvers, and then fabricated and measured by coplanar waveguide (CPW) probe to confirm its practical performance.
- Open Access
- 4 May 2023
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 133 (17)
Metastable and field-induced ferroelectric response in antiferroelectric lead zirconate thin film studied by the hyperbolic law and third harmonic response
In this paper, the field-induced residual ferroelectricity in antiferroelectric lead zirconate thin films has been studied by impedance measurements together with a hyperbolic law analysis, which permits us to extract the different contributions to the material’s complex permittivity. By measuring the Rayleigh coefficient αr, it appears that the residual ferroelectricity is considerably enhanced when the sample has been previously exposed to an electric field close to the antiferroelectric to ferroelectric transition field. This indicates that a part of the material remains ferroelectric after the antiferroelectric–ferroelectric backward transition, which constitutes an additional contribution to polarization. Consequently, a higher domain wall density and mobility can be observed. Measurements after exposition to thermal treatment show that this ferroelectric response is metastable.
- 4 May 2023
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 133 (17)
Open AccessMetastable and field-induced ferroelectric response in antiferroelectric lead zirconate thin film studied by the hyperbolic law and third harmonic response
In this paper, the field-induced residual ferroelectricity in antiferroelectric lead zirconate thin films has been studied by impedance measurements together with a hyperbolic law analysis, which permits us to extract the different contributions to the material’s complex permittivity. By measuring the Rayleigh coefficient αr, it appears that the residual ferroelectricity is considerably enhanced when the sample has been previously exposed to an electric field close to the antiferroelectric to ferroelectric transition field. This indicates that a part of the material remains ferroelectric after the antiferroelectric–ferroelectric backward transition, which constitutes an additional contribution to polarization. Consequently, a higher domain wall density and mobility can be observed. Measurements after exposition to thermal treatment show that this ferroelectric response is metastable.
- 7 April 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control
- Vol. 67 (9) , 1733-1737
Design and Development of a Tunable Ferroelectric Microwave Surface Mounted Device
Based on a Ba(1-x)SrxTiO3 ferroelectric thin film, a discrete tunable surface mounted device (SMD) capacitor has been developed for microwave frequency applications purpose. The proposed SMD topology has the particular advantage of inherent decoupling between the RF signal and the DC biasing voltage, necessary to tune the ferroelectric permittivity. The design and technological development of the SMD component is presented and synthesis of the ferroelectric thin film is summarized. Material characterization shows convenient tunability, while low dielectric losses at 10 MHz. Integration of the SMD tunable capacitor into a Planar Inverted-F Antenna has been done in order to evaluate the agility and tunability performance of the antenna.
- 7 April 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control
- Vol. 67 (9) , 1733-1737
Design and Development of a Tunable Ferroelectric Microwave Surface Mounted Device
Based on a Ba(1-x)SrxTiO3 ferroelectric thin film, a discrete tunable surface mounted device (SMD) capacitor has been developed for microwave frequency applications purpose. The proposed SMD topology has the particular advantage of inherent decoupling between the RF signal and the DC biasing voltage, necessary to tune the ferroelectric permittivity. The design and technological development of the SMD component is presented and synthesis of the ferroelectric thin film is summarized. Material characterization shows convenient tunability, while low dielectric losses at 10 MHz. Integration of the SMD tunable capacitor into a Planar Inverted-F Antenna has been done in order to evaluate the agility and tunability performance of the antenna.