Alexander Ovchinnikov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Alexander Ovchinnikov has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Nadiia Kovalova
Навчально-науковий інститут «Український державний хіміко-технологічний університет», Український Державний університет науки і технологій
2 shared publications - Oleh Kalinichenko
Ukrainian State University of Science and Technologies
2 shared publications - Игорь Андреевич Петрик
АТ «Мотор Січ», Запоріжжя
2 shared publications - Костянтин Михайлович Сухий
член-кореспондент НАН України, ректор Українського державного університету науки і технологій
2 shared publications - Dmytro Kuts
Ukrainian State University of Science and Technologies
1 shared publication - Maria Matkovskaya
Zaporizhia National Technical University Zhukovskoho str., 64, Zaporizhia, Ukraine, 69063
1 shared publication
Latest Publications
- 1 December 2024
- Published by SHEI Ukrainian State University of Chemical Technology in Voprosy Khimii i Khimicheskoi Tekhnologii
- No. 6
Properties of Zr–Ti–Nb and Ti–Al–V alloys
This article is devoted to studying the properties of the new Zr–Ti–Nb alloy and comparing it with the well-known Ti–Al–V alloy (ВТ-6, Grade 5 analog). The properties were analyzed through chemical composition determination and corrosion resistance assessment. The Zr–Ti–Nb alloy does not contain the toxic impurities present in the Ti–Al–V alloy, specifically aluminum and vanadium. Structural studies were conducted to identify the phases (X-ray diffraction analysis) and their composition using scanning electron microscopy. The microstructure and phase composition of the Zr–Ti–Nb alloy indicated a uniform distribution of elements throughout the alloy. The wetting angle of the Zr–Ti–Nb alloy with an oxide layer is significantly smaller than that of the Ti–Al–V alloy, suggesting greater hydrophilicity. Physical research methods included determining density, reflectivity, and electrical conductivity. Mechanical properties were examined by determining the elastic modulus, strength limit, yield strength, longitudinal elongation, transverse contraction, and microhardness. Notably, the elastic modulus of the Zr–Ti–Nb alloy is 26.4 GPa, similar to that of cortical bone, in contrast to the Ti–Al–V alloy, which has an elastic modulus of 110–140 GPa. The obtained data indicate that the superior chemical and mechanical properties of the Zr–Ti–Nb alloy make it suitable for medical applications.
- 1 December 2024
- Published by SHEI Ukrainian State University of Chemical Technology in Voprosy Khimii i Khimicheskoi Tekhnologii
- No. 6
Properties of Zr–Ti–Nb and Ti–Al–V alloys
This article is devoted to studying the properties of the new Zr–Ti–Nb alloy and comparing it with the well-known Ti–Al–V alloy (ВТ-6, Grade 5 analog). The properties were analyzed through chemical composition determination and corrosion resistance assessment. The Zr–Ti–Nb alloy does not contain the toxic impurities present in the Ti–Al–V alloy, specifically aluminum and vanadium. Structural studies were conducted to identify the phases (X-ray diffraction analysis) and their composition using scanning electron microscopy. The microstructure and phase composition of the Zr–Ti–Nb alloy indicated a uniform distribution of elements throughout the alloy. The wetting angle of the Zr–Ti–Nb alloy with an oxide layer is significantly smaller than that of the Ti–Al–V alloy, suggesting greater hydrophilicity. Physical research methods included determining density, reflectivity, and electrical conductivity. Mechanical properties were examined by determining the elastic modulus, strength limit, yield strength, longitudinal elongation, transverse contraction, and microhardness. Notably, the elastic modulus of the Zr–Ti–Nb alloy is 26.4 GPa, similar to that of cortical bone, in contrast to the Ti–Al–V alloy, which has an elastic modulus of 110–140 GPa. The obtained data indicate that the superior chemical and mechanical properties of the Zr–Ti–Nb alloy make it suitable for medical applications.
- Open Access
- 28 November 2024
- Published by Khmelnytskyi National University in Herald of Khmelnytskyi National University. Technical sciences
- Vol. 345 (6(2)) , 218-225
МЕТОДИКА КОМП’ЮТЕРНОГО МОДЕЛЮВАННЯ ПРИ СТВОРЕННІ ІНДИВІДУАЛІЗОВАНИХ ІМПЛАНТАТІВ
Робота присвячена опису методики моделювання індивідуалізованих імплантатів із застосуванням медичної інформації. Методика складається з п’яти кроків. Для реалізації методики потрібно застосування комп’ютерних програм InVesalius, SolidWorks, PrusaSlicer та деяких інших. Першим кроком є одержання скану тіла людини за допомогою комп'ютерної томографії або магніто-резонансної томографії у форматі DICOM. Другим кроком є завантаження пакету DICOM в комп'ютерну програму InVesalius для одержання комп'ютерного файлу зі зшитою поверхнею форми кістки. Третім кроком є виготовлення 3D комп'ютерної твердотільної моделі кістки в програмі SolidWorks. Четвертим є підготовка моделі до 3D друку з допомогою програми PrusaSlicer і 3D друк прототипу кістки пластиком. П’ятим кроком є друк імплантату в металі на 3D принтері. Подана методика дозволяє швидко та точно проєктувати, друкувати у пластику для узгодження плану оперативного втручання та передавати твердотільну модель для друку металом на 3D принтері з виготовленням індивідуалізованого імплантату.
- 28 November 2024
- Published by Khmelnytskyi National University in Herald of Khmelnytskyi National University. Technical sciences
- Vol. 345 (6(2)) , 218-225
Open AccessМЕТОДИКА КОМП’ЮТЕРНОГО МОДЕЛЮВАННЯ ПРИ СТВОРЕННІ ІНДИВІДУАЛІЗОВАНИХ ІМПЛАНТАТІВ
Робота присвячена опису методики моделювання індивідуалізованих імплантатів із застосуванням медичної інформації. Методика складається з п’яти кроків. Для реалізації методики потрібно застосування комп’ютерних програм InVesalius, SolidWorks, PrusaSlicer та деяких інших. Першим кроком є одержання скану тіла людини за допомогою комп'ютерної томографії або магніто-резонансної томографії у форматі DICOM. Другим кроком є завантаження пакету DICOM в комп'ютерну програму InVesalius для одержання комп'ютерного файлу зі зшитою поверхнею форми кістки. Третім кроком є виготовлення 3D комп'ютерної твердотільної моделі кістки в програмі SolidWorks. Четвертим є підготовка моделі до 3D друку з допомогою програми PrusaSlicer і 3D друк прототипу кістки пластиком. П’ятим кроком є друк імплантату в металі на 3D принтері. Подана методика дозволяє швидко та точно проєктувати, друкувати у пластику для узгодження плану оперативного втручання та передавати твердотільну модель для друку металом на 3D принтері з виготовленням індивідуалізованого імплантату.
- Open Access
- 18 April 2024
- Published by National Aerospace University - Kharkiv Aviation Institute in Aerospace technic and technology
- No. 2,p. 49-56
Визначення власних частот та форм коливань лопатки турбіни, виготовленої зі сплаву на основі алюмініду титану
This paper investigates the possibility of manufacturing the working blade of the 2nd stage of the free turbine from an experimental alloy based on titanium aluminide of the Ti-28Al-7Nb-2Mo-0.3 (Y, Re, B) system. Alloys of this class are important structural materials with a unique set of physical and mechanical characteristics. Alloys based on aluminide are characterized by low density, high heat strength, and heat resistance and have a high potential to replace nickel-based alloys designed for operation at temperatures no higher than 850°C. However, the use of a new alloy for the manufacture of a turbine blade involves calculations of the strength and oscillations of the blades. The purpose of the calculations is to determine the possibility of using an aluminide-based alloy of the Ti-28Al-7Nb-2Mo-0.3 (Y, Re, B) system instead of the VZHL12E-VI alloy for the selected working blade. The research was carried out by performing a modal analysis, determining the stress-deformed state, and checking the strength and mass characteristics. The physical properties of the materials were used as the initial data for the calculation. The geometry and temperature distribution of the blade and its fixing remained constant for the two options. A three-dimensional model of the experimental vane was built using the Unigraphics NX system, and a finite element model was developed using the Ansys software complex. It was established that when an experimental alloy is used, the mass of one blade is reduced by almost 40%. Using the finite element method, the natural frequencies and forms of blade oscillations were calculated, and Campbell’s diagrams were constructed for the original and experimental blades for the nominal operation of the engine. When using an experimental alloy, the frequencies of the blades’ natural oscillations are further from the resonant frequency. The distribution of equivalent stresses was determined, and it was shown that the maximum stresses act in the root section of the blade feather. When using the experimental alloy based on titanium aluminide, the equivalent stresses are reduced by 35% compared with the initial values. It is shown that the safety margin of the proposed material is not less than that of the VZHL12E-VI alloy.
- 18 April 2024
- Published by National Aerospace University - Kharkiv Aviation Institute in Aerospace technic and technology
- No. 2,p. 49-56
Open AccessВизначення власних частот та форм коливань лопатки турбіни, виготовленої зі сплаву на основі алюмініду титану
This paper investigates the possibility of manufacturing the working blade of the 2nd stage of the free turbine from an experimental alloy based on titanium aluminide of the Ti-28Al-7Nb-2Mo-0.3 (Y, Re, B) system. Alloys of this class are important structural materials with a unique set of physical and mechanical characteristics. Alloys based on aluminide are characterized by low density, high heat strength, and heat resistance and have a high potential to replace nickel-based alloys designed for operation at temperatures no higher than 850°C. However, the use of a new alloy for the manufacture of a turbine blade involves calculations of the strength and oscillations of the blades. The purpose of the calculations is to determine the possibility of using an aluminide-based alloy of the Ti-28Al-7Nb-2Mo-0.3 (Y, Re, B) system instead of the VZHL12E-VI alloy for the selected working blade. The research was carried out by performing a modal analysis, determining the stress-deformed state, and checking the strength and mass characteristics. The physical properties of the materials were used as the initial data for the calculation. The geometry and temperature distribution of the blade and its fixing remained constant for the two options. A three-dimensional model of the experimental vane was built using the Unigraphics NX system, and a finite element model was developed using the Ansys software complex. It was established that when an experimental alloy is used, the mass of one blade is reduced by almost 40%. Using the finite element method, the natural frequencies and forms of blade oscillations were calculated, and Campbell’s diagrams were constructed for the original and experimental blades for the nominal operation of the engine. When using an experimental alloy, the frequencies of the blades’ natural oscillations are further from the resonant frequency. The distribution of equivalent stresses was determined, and it was shown that the maximum stresses act in the root section of the blade feather. When using the experimental alloy based on titanium aluminide, the equivalent stresses are reduced by 35% compared with the initial values. It is shown that the safety margin of the proposed material is not less than that of the VZHL12E-VI alloy.
- 24 February 2022
- Published by National Aerospace University - Kharkiv Aviation Institute in Aerospace technic and technology
- No. 1,p. 57-63
Досвід впровадження адитивних технологій при ремонті деталей ГТД зі сплава ЕП 648 ВІ (ХН50ВМТЮБ-ВІ) в умовах серійного виробництва
Technology has been developed for repairing the nozzle assembly (SA) casing in the D-18T engine by additively growing the damaged part by microplasma surfacing with a powder of EP648VI (KhN50VMTYUB-VI) alloy. Traditionally, a part with such damage was rejected. The cost of replacing a damaged part with a new one is about 200 thousand hryvnias. The article discusses the equipment and features of the growing technology using the method of microplasma multilayer surfacing. Additive growth of the cut-damaged part was carried out on a STARWELD 190 H robotic installation for microplasma powder surfacing using EP648 VI alloy powders with a 63–163 micron fraction. After growing, heat treatment (aging at 700 ºС, exposure for 16 hours), mechanical processing, and quality control of the grown part were carried out. To create an evidence base to determine the possibility of installing a repaired part on the engine, a set of studies was carried out, which included the determination of the chemical composition of samples grown using a technology similar to repair, metallographic studies, and mechanical tests. As a result, it was found that the chemical composition of the deposited metal meets the requirements of the technical specifications TU 14-1-3046-97 "Bars made of heat-resistant alloy grade KhN50VMTYUB (EP648), and the microstructure of the deposited metal after heat treatment is a γ - solid solution with the presence of carbides, carbonitrides and a small amount of γ´ phase, which corresponds to the normally heat-treated state of the EP 648 VI (KhN50VMTYUB-VI) alloy and the level of mechanical properties of the grown alloy with subsequent serial heat treatment (aging at 700 ° C, holding for 16 hours) not lower than the level of the forging used at serial production of a part. The economic effect of the introduction of this technology is shown, which is more than 100 thousand hryvnias (about 23% of the cost of a new part).
- 24 February 2022
- Published by National Aerospace University - Kharkiv Aviation Institute in Aerospace technic and technology
- No. 1,p. 57-63
Досвід впровадження адитивних технологій при ремонті деталей ГТД зі сплава ЕП 648 ВІ (ХН50ВМТЮБ-ВІ) в умовах серійного виробництва
Technology has been developed for repairing the nozzle assembly (SA) casing in the D-18T engine by additively growing the damaged part by microplasma surfacing with a powder of EP648VI (KhN50VMTYUB-VI) alloy. Traditionally, a part with such damage was rejected. The cost of replacing a damaged part with a new one is about 200 thousand hryvnias. The article discusses the equipment and features of the growing technology using the method of microplasma multilayer surfacing. Additive growth of the cut-damaged part was carried out on a STARWELD 190 H robotic installation for microplasma powder surfacing using EP648 VI alloy powders with a 63–163 micron fraction. After growing, heat treatment (aging at 700 ºС, exposure for 16 hours), mechanical processing, and quality control of the grown part were carried out. To create an evidence base to determine the possibility of installing a repaired part on the engine, a set of studies was carried out, which included the determination of the chemical composition of samples grown using a technology similar to repair, metallographic studies, and mechanical tests. As a result, it was found that the chemical composition of the deposited metal meets the requirements of the technical specifications TU 14-1-3046-97 "Bars made of heat-resistant alloy grade KhN50VMTYUB (EP648), and the microstructure of the deposited metal after heat treatment is a γ - solid solution with the presence of carbides, carbonitrides and a small amount of γ´ phase, which corresponds to the normally heat-treated state of the EP 648 VI (KhN50VMTYUB-VI) alloy and the level of mechanical properties of the grown alloy with subsequent serial heat treatment (aging at 700 ° C, holding for 16 hours) not lower than the level of the forging used at serial production of a part. The economic effect of the introduction of this technology is shown, which is more than 100 thousand hryvnias (about 23% of the cost of a new part).
- Open Access
- 26 February 2019
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 1 (12 (97)) , 49-55
Detecting the influence of heat sources on material properties when producing aviation parts by a direct energy deposition method
Detecting the influence of heat sources on material properties when producing aviation parts by a direct energy deposition method
- 26 February 2019
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 1 (12 (97)) , 49-55
Open AccessDetecting the influence of heat sources on material properties when producing aviation parts by a direct energy deposition method
Detecting the influence of heat sources on material properties when producing aviation parts by a direct energy deposition method