Jung Wan Lee
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Jung Wan Lee has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Jung Soo Kim
Composites Research Division, Korea Institute of Materials Science (KIMS), 797 Changwon-daero, Seongsan-gu, Changwon-si 51508, Gyeongsangnam-do, Republic of Korea
2 shared publications - Moon-Kwang Um
Composites Research Division, Korea Institute of Materials Science (KIMS), 797 Changwon-daero, Seongsan-gu, Changwon-si 51508, Gyeongsangnam-do, Republic of Korea
2 shared publications - Hyeong-Min Yoo
School of Mechanical Engineering Kookmin University Seoul Republic of Korea
1 shared publication - Hyung Doh Roh
Hanyang University ERICA
1 shared publication - Sehun An
Composites Research Division, Korea Institute of Materials Science (KIMS), 797 Changwon-daero, Seongsan-gu, Changwon-si 51508, Gyeongsangnam-do, Republic of Korea
1 shared publication - Wiedae Kim
Department of Aerospace Engineering, Pusan National University, Busan, Republic of Korea
1 shared publication
Latest Publications
- Open Access
Effect of Peel Ply on Resin Flow during Vacuum Infusion
Although various simulations have been conducted for the vacuum infusion process, most of the studies have considered only fabrics and flow medium and ignored the effect of peel ply. However, peel ply can affect resin flow because it is placed between the fabrics and flow medium. To verify this, permeability of two types of peel plies was measured, and it was found that the permeability between the peel plies differed significantly. Moreover, the permeability of the peel plies was lower than that of the carbon fabric; thus, peel ply can cause a bottleneck in the flow in the out-of-plane direction. Some 3D flow simulations were conducted in cases of no peel ply and for two types of the peel plies to confirm the effect of peel ply, and experiments were also conducted for two types of the peel plies. It was observed that filling time and flow pattern were highly dependent on the peel plies. The smaller permeability of peel ply has, the greater effect of peel ply is. These results indicate that the permeability of peel ply is one of the dominant factors and should be considered in process design in vacuum infusion. Additionally, by adding one layer of peel ply and applying permeability, the accuracy of flow simulations can be improved for filling time and pattern.
Open AccessEffect of Peel Ply on Resin Flow during Vacuum Infusion
Although various simulations have been conducted for the vacuum infusion process, most of the studies have considered only fabrics and flow medium and ignored the effect of peel ply. However, peel ply can affect resin flow because it is placed between the fabrics and flow medium. To verify this, permeability of two types of peel plies was measured, and it was found that the permeability between the peel plies differed significantly. Moreover, the permeability of the peel plies was lower than that of the carbon fabric; thus, peel ply can cause a bottleneck in the flow in the out-of-plane direction. Some 3D flow simulations were conducted in cases of no peel ply and for two types of the peel plies to confirm the effect of peel ply, and experiments were also conducted for two types of the peel plies. It was observed that filling time and flow pattern were highly dependent on the peel plies. The smaller permeability of peel ply has, the greater effect of peel ply is. These results indicate that the permeability of peel ply is one of the dominant factors and should be considered in process design in vacuum infusion. Additionally, by adding one layer of peel ply and applying permeability, the accuracy of flow simulations can be improved for filling time and pattern.
- Open Access
- 10 October 2020
- Published by MDPI AG in Applied Sciences
- Vol. 10 (20) , 7039
Influence of Non-Reactive Epoxy Binder on the Permeability and Friction Coefficient of Twill-Woven Carbon Fabric in the Liquid Composite Molding Process
In the liquid composite molding process, a binder is used to fix the preform. In this study, the influence of a non-reactive epoxy binder was investigated. To allow the measurement of permeability, the preform specimen was produced under three preforming conditions: neat fabric preform, binder-treated fabric preform without heat treatment, and binder-treated fabric preform with heat treatment. The in-plane directional permeability, K1 (having maximum flow velocity), and K2 (having minimum flow velocity) of the binder-treated fabric preform decreased approximately 80% compared to the neat fabric preform. The permeability in the out-of-plane direction decreased approximately 80% in the binder-treated fabric preform without heat treatment and about 98% in the binder-treated fabric preform with heat treatment. This decrease occurred because the treated binder on the fiber hindered resin impregnation. The effect of the binder on the friction coefficient of carbon fabric was also investigated. The friction coefficient was high when the binder was on the friction surface and increased 40–200% at 110 °C, compared to 25 °C.
- 10 October 2020
- Published by MDPI AG in Applied Sciences
- Vol. 10 (20) , 7039
Open AccessInfluence of Non-Reactive Epoxy Binder on the Permeability and Friction Coefficient of Twill-Woven Carbon Fabric in the Liquid Composite Molding Process
In the liquid composite molding process, a binder is used to fix the preform. In this study, the influence of a non-reactive epoxy binder was investigated. To allow the measurement of permeability, the preform specimen was produced under three preforming conditions: neat fabric preform, binder-treated fabric preform without heat treatment, and binder-treated fabric preform with heat treatment. The in-plane directional permeability, K1 (having maximum flow velocity), and K2 (having minimum flow velocity) of the binder-treated fabric preform decreased approximately 80% compared to the neat fabric preform. The permeability in the out-of-plane direction decreased approximately 80% in the binder-treated fabric preform without heat treatment and about 98% in the binder-treated fabric preform with heat treatment. This decrease occurred because the treated binder on the fiber hindered resin impregnation. The effect of the binder on the friction coefficient of carbon fabric was also investigated. The friction coefficient was high when the binder was on the friction surface and increased 40–200% at 110 °C, compared to 25 °C.