Hyung Doh Roh
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Hyung Doh Roh has a total of 40 co-authors. Here are the top co-authors by number of shared publications:
Young-Bin Park
4 shared publicationsIn Yong Lee
3 shared publicationsMoon-Kwang Um
3 shared publicationsJung-Soo Kim
2 shared publicationsJungwan Lee
2 shared publications- Yakun Li2 shared publications
Latest Publications
- Open Access
- 11 September 2026
- Published by Elsevier in SSRN Electronic Journal
Analysis of Thermal Expansion and Torsional Behavior of FDM Additively Manufactured Polyethersulfone and Carbon Fiber-Reinforced Polyethersulfone Composites for Wind Turbine Blade Molds
This study investigates the thermal expansion and torsional behavior of polyethersulfone (PES), and carbon fiber reinforced PES composites fabricated by fused deposition modeling (FDM) for high temperature vacuum assisted resin infusion tooling. Three material systems, neat PES, chopped carbon fiber reinforced PES and milled carbon fiber reinforced PES, were examined with unidirectional [UD], [0/90] and [0/45/90/135] stacking configurations. Experiments conducted in an oven measured thermal deformation, Classical Laminate Plate Theory (CLPT) explained stacking effects on bending and torsion, and three-dimensional finite element analysis (FEA) in ANSYS quantified deformation and torsion. In the oven experiment, carbon fiber reinforcement strongly reduced in plane thermal strain: CCF PES and MCF PES showed in plane strains approximately 26 to 38% of neat PES, while through thickness strains remained similar. In FEA, CCF PES reduced in plane thermal strain by approximately 60% and through thickness strain by 40 to 45% relative to PES. Torsion angle, calculated from Z directional deformation along the top edge, was essentially zero for [UD] and [0/90], while [0/45/90/135] produced 0.0035° (PES) and 0.0014° (CCF PES). CLPT and FEA agreed closely, with CCF PES showing approximately 58.5% (CLPT) and 60% (FEA) lower torsion angle than PES for [0/45/90/135]. Asymmetric stacking and geometry further increased the torsion angle. The wind turbine blade mold showed the same reinforcement trend, with [0/45/90/135] producing 0.0026° (PES) and 0.0011° (CCF PES). These results indicate that stacking configuration governs the occurrence of torsion, and carbon fiber reinforcement reduces both directional thermal strain and torsional deformation magnitude.
- 11 September 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessAnalysis of Thermal Expansion and Torsional Behavior of FDM Additively Manufactured Polyethersulfone and Carbon Fiber-Reinforced Polyethersulfone Composites for Wind Turbine Blade Molds
This study investigates the thermal expansion and torsional behavior of polyethersulfone (PES), and carbon fiber reinforced PES composites fabricated by fused deposition modeling (FDM) for high temperature vacuum assisted resin infusion tooling. Three material systems, neat PES, chopped carbon fiber reinforced PES and milled carbon fiber reinforced PES, were examined with unidirectional [UD], [0/90] and [0/45/90/135] stacking configurations. Experiments conducted in an oven measured thermal deformation, Classical Laminate Plate Theory (CLPT) explained stacking effects on bending and torsion, and three-dimensional finite element analysis (FEA) in ANSYS quantified deformation and torsion. In the oven experiment, carbon fiber reinforcement strongly reduced in plane thermal strain: CCF PES and MCF PES showed in plane strains approximately 26 to 38% of neat PES, while through thickness strains remained similar. In FEA, CCF PES reduced in plane thermal strain by approximately 60% and through thickness strain by 40 to 45% relative to PES. Torsion angle, calculated from Z directional deformation along the top edge, was essentially zero for [UD] and [0/90], while [0/45/90/135] produced 0.0035° (PES) and 0.0014° (CCF PES). CLPT and FEA agreed closely, with CCF PES showing approximately 58.5% (CLPT) and 60% (FEA) lower torsion angle than PES for [0/45/90/135]. Asymmetric stacking and geometry further increased the torsion angle. The wind turbine blade mold showed the same reinforcement trend, with [0/45/90/135] producing 0.0026° (PES) and 0.0011° (CCF PES). These results indicate that stacking configuration governs the occurrence of torsion, and carbon fiber reinforcement reduces both directional thermal strain and torsional deformation magnitude.
- Top Cited PapersOpen Access
- 10 February 2026
- Published by Elsevier in Polymer Testing
- Vol. 156
Recent advances in manufacturing and post-processing of fiber-reinforced thermoset and thermoplastic composites: A multi-domain perspective
- 10 February 2026
- Published by Elsevier in Polymer Testing
- Vol. 156
Top Cited PapersOpen AccessRecent advances in manufacturing and post-processing of fiber-reinforced thermoset and thermoplastic composites: A multi-domain perspective
- 3 November 2025
- Published by SAGE Publications in Journal of Sandwich Structures & Materials
- Vol. 28 (4) , 676-700
One-shot manufacturing of foam core sandwich composite without adhesive and its acousto-ultrasonic non-destructive evaluation
This study investigates the interfacial bonding reliability of CFRP/PVC foam core sandwich composites fabricated via a one-shot co-curing process without adhesive film, aiming to overcome the limitations of conventional multi-step bonding methods. Various types of carbon fiber prepregs were co-cured with a PVC foam core in a single-step process using either an oven or a hot press. To assess the bonding strength, mechanical testing, optical microscopy, and ultrasonic testing were conducted, focusing on the resin impregnation into the core. The results showed that the 3K and 12K configurations achieved sufficient bonding strength even without adhesive film, with failures mainly occurring within the foam core. The strengths of the adhesive-less composite was as acceptable as only 0–3.63% difference in average was observed with 5.75–9.34% weight reduction and 19.22–29.74% cost saving in compared to the conventional composite. In contrast, the UD and 6K configurations exhibited interfacial debonding because of insufficient resin impregnation to the foam core. Ultrasonic non-destructive evaluation analyzed the interfacial bonding at the interface. This study revealed the structural feasibility of adhesive-free one-shot co-curing. The proposed method enables reliable sandwich composite manufacturing without adhesive film, enhancing the lightweight and cost.
- 3 November 2025
- Published by SAGE Publications in Journal of Sandwich Structures & Materials
- Vol. 28 (4) , 676-700
One-shot manufacturing of foam core sandwich composite without adhesive and its acousto-ultrasonic non-destructive evaluation
This study investigates the interfacial bonding reliability of CFRP/PVC foam core sandwich composites fabricated via a one-shot co-curing process without adhesive film, aiming to overcome the limitations of conventional multi-step bonding methods. Various types of carbon fiber prepregs were co-cured with a PVC foam core in a single-step process using either an oven or a hot press. To assess the bonding strength, mechanical testing, optical microscopy, and ultrasonic testing were conducted, focusing on the resin impregnation into the core. The results showed that the 3K and 12K configurations achieved sufficient bonding strength even without adhesive film, with failures mainly occurring within the foam core. The strengths of the adhesive-less composite was as acceptable as only 0–3.63% difference in average was observed with 5.75–9.34% weight reduction and 19.22–29.74% cost saving in compared to the conventional composite. In contrast, the UD and 6K configurations exhibited interfacial debonding because of insufficient resin impregnation to the foam core. Ultrasonic non-destructive evaluation analyzed the interfacial bonding at the interface. This study revealed the structural feasibility of adhesive-free one-shot co-curing. The proposed method enables reliable sandwich composite manufacturing without adhesive film, enhancing the lightweight and cost.
- 12 June 2025
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing
- Vol. 26 (8) , 2093-2109
Sandwich Composites Manufacturing: A Review of Materials, Methods, Applications and Challenges
- 12 June 2025
- Published by Springer Nature in International Journal of Precision Engineering and Manufacturing
- Vol. 26 (8) , 2093-2109
Sandwich Composites Manufacturing: A Review of Materials, Methods, Applications and Challenges
- Open Access
- 3 June 2025
- Published by Elsevier in Nuclear Engineering and Technology
- Vol. 57 (10)
Numerical analysis of residual stress in the bending process using kinematic isotropic hardening models for a helical tube in SMR and a U-bent tube in PWR
- 3 June 2025
- Published by Elsevier in Nuclear Engineering and Technology
- Vol. 57 (10)
Open AccessNumerical analysis of residual stress in the bending process using kinematic isotropic hardening models for a helical tube in SMR and a U-bent tube in PWR
- 27 May 2025
- Published by IOP Publishing in Functional Composites and Structures
- Vol. 7 (2) , 025004
Joining technology of carbon fiber reinforced polymer (CFRP) using copper wire and adhesive
This paper investigates a novel approach for joining carbon fiber reinforced polymer (CFRP) composites, aiming to mitigate fiber continuity disruptions and stress concentrations typically associated with conventional mechanical joining methods such as bolts and rivets. Specifically, the study examines the effects of copper wires (diameter: 0.25 mm), arranged horizontally and vertically on the CFRP surface, on adhesive bonding performance under curing conditions of 170 °C for 15 min. Single-lap shear tests and optical microscopy analyses were conducted to evaluate the influence of wire orientation and curing conditions on interfacial strength, adhesive mechanisms, and failure modes. Vertically aligned copper wires achieved the highest average shear strength of 20 MPa, representing a maximum load increase of 439.74% compared to adhesive-only joints. Surpassing horizontal and no-wire samples. This improvement is attributed to enhanced adhesive infiltration and mechanical interlocking at the interface, leading to more cohesive failure within the adhesive layer. The results demonstrate that copper wire orientation significantly impacts adhesive penetration, interface quality, and fracture characteristics. Furthermore, optimized curing conditions improve adhesive stability and reduce interfacial degradation, reinforcing the tendency toward cohesive failure. This study provides quantitative and practical insights into copper wire-reinforced bonding mechanisms, facilitating advancements in composite electronics and structural applications.
- 27 May 2025
- Published by IOP Publishing in Functional Composites and Structures
- Vol. 7 (2) , 025004
Joining technology of carbon fiber reinforced polymer (CFRP) using copper wire and adhesive
This paper investigates a novel approach for joining carbon fiber reinforced polymer (CFRP) composites, aiming to mitigate fiber continuity disruptions and stress concentrations typically associated with conventional mechanical joining methods such as bolts and rivets. Specifically, the study examines the effects of copper wires (diameter: 0.25 mm), arranged horizontally and vertically on the CFRP surface, on adhesive bonding performance under curing conditions of 170 °C for 15 min. Single-lap shear tests and optical microscopy analyses were conducted to evaluate the influence of wire orientation and curing conditions on interfacial strength, adhesive mechanisms, and failure modes. Vertically aligned copper wires achieved the highest average shear strength of 20 MPa, representing a maximum load increase of 439.74% compared to adhesive-only joints. Surpassing horizontal and no-wire samples. This improvement is attributed to enhanced adhesive infiltration and mechanical interlocking at the interface, leading to more cohesive failure within the adhesive layer. The results demonstrate that copper wire orientation significantly impacts adhesive penetration, interface quality, and fracture characteristics. Furthermore, optimized curing conditions improve adhesive stability and reduce interfacial degradation, reinforcing the tendency toward cohesive failure. This study provides quantitative and practical insights into copper wire-reinforced bonding mechanisms, facilitating advancements in composite electronics and structural applications.