Ozlem Celik Sola
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Ozlem Celik Sola has a total of 24 co-authors. Here are the top co-authors by number of shared publications:
- Baris Sayin
Istanbul University-Cerrahpaşa, Türkiye
6 shared publications - Cengiz Duran Atiş
Department of Civil Engineering, Erciyes University, Kayseri 38039, Turkey
4 shared publications - Levent Bostanci
Building Insulation Technologies Programme, School of Advanced Vocational Studies, Istanbul Beykent University, 34520 Istanbul, Turkey
3 shared publications - A. Mehmet Haksever
Associate Professor, Dept. of Civil Engineering, Faculty of Engineering, Istanbul Univ., Avcilar, Istanbul, Turkey
1 shared publication - Abdurrahman Güner
Professor, Dept. of Civil Engineering, Istanbul Univ., Istanbul 34320, Turkey
1 shared publication - Asadullah Zaki
İstanbul Üniversitesi-Cerrahpaşa
1 shared publication
Latest Publications
- Open Access
Effect of Rice Husk Ash Addition on Durability Properties of Mortars
Prismatic mortar specimens with dimensions of 40 × 40 × 160 mm were produced in accordance with TS EN 196-1:2016 using rice husk ash (RHA) as a partial cement replacement at levels ranging from 0% to 15%. The specimens were exposed to aggressive seawater and 7% NaCl environments and evaluated through compressive strength, flexural strength, ultrasonic pulse velocity (UPV), water absorption, carbonation, capillary water absorption, and thermal conductivity tests. The highest compressive strength values were generally obtained at RHA replacement levels of 8–10%, depending on the exposure condition and curing period. In the 7% NaCl environment, most RHA-incorporated mixtures exhibited higher flexural strength than the control mixture, with the highest values generally observed at replacement levels between 6% and 10%. UPV results indicated that the incorporation of RHA did not significantly impair the internal quality of the mortars. Water absorption, capillary water absorption, and carbonation depth generally increased with increasing RHA content, particularly at replacement levels of 10–15%. No carbonation depth was observed in the control specimens, whereas the highest carbonation depths were measured in the 15% RHA mixtures. Thermal conductivity decreased with increasing RHA content, with the lowest values obtained at the highest replacement levels. Overall, the results indicate that RHA replacement levels of approximately 8–10% provide a favorable balance between mechanical performance, durability-related properties, and thermal insulation performance under aggressive chloride-rich exposure conditions.
Open AccessEffect of Rice Husk Ash Addition on Durability Properties of Mortars
Prismatic mortar specimens with dimensions of 40 × 40 × 160 mm were produced in accordance with TS EN 196-1:2016 using rice husk ash (RHA) as a partial cement replacement at levels ranging from 0% to 15%. The specimens were exposed to aggressive seawater and 7% NaCl environments and evaluated through compressive strength, flexural strength, ultrasonic pulse velocity (UPV), water absorption, carbonation, capillary water absorption, and thermal conductivity tests. The highest compressive strength values were generally obtained at RHA replacement levels of 8–10%, depending on the exposure condition and curing period. In the 7% NaCl environment, most RHA-incorporated mixtures exhibited higher flexural strength than the control mixture, with the highest values generally observed at replacement levels between 6% and 10%. UPV results indicated that the incorporation of RHA did not significantly impair the internal quality of the mortars. Water absorption, capillary water absorption, and carbonation depth generally increased with increasing RHA content, particularly at replacement levels of 10–15%. No carbonation depth was observed in the control specimens, whereas the highest carbonation depths were measured in the 15% RHA mixtures. Thermal conductivity decreased with increasing RHA content, with the lowest values obtained at the highest replacement levels. Overall, the results indicate that RHA replacement levels of approximately 8–10% provide a favorable balance between mechanical performance, durability-related properties, and thermal insulation performance under aggressive chloride-rich exposure conditions.
- Open Access
- 1 January 2022
- Published by Pontificia Universidad Catolica de Chile in Revista de la construcción
- Vol. 21 (2) , 368-386
Effect of aerogel/silica fume under curing methods on properties of cement-based mortars
In this study, the mechanical, thermal and porosity properties of mortar samples containing aerogel and silica fume under different curing conditions were investigated. For this purpose, 0%, 0.25% and 0.50% by weight of silica aerogel as a cement additive and 10% silica fume as an industrial waste material were incorporated in the cement mixtures. The prepared mortar samples were exposed to curing process in water, the wetting-drying effect and MgSO4 effect for 16 weeks. The highest thermal conductivity reduction of 31.2% was obtained from the water curing sample with silica fume addition at an aerogel content of 0.25%. Maximum compressive and flexural strengths were determined respectively from samples with silica fume addition at an aerogel content 0.50% as 74.5 MPa and no aerogel content as 11.3 MPa by wetting-drying curing. However, the lowest thermal conductivity coefficient was measured as 1.458 W/mK from the sample at an 0.25% aerogel content containing silica fume which completed the curing process under the influence of MgSO4 with a highest compressive strength increase by 24.6%.
- 1 January 2022
- Published by Pontificia Universidad Catolica de Chile in Revista de la construcción
- Vol. 21 (2) , 368-386
Open AccessEffect of aerogel/silica fume under curing methods on properties of cement-based mortars
In this study, the mechanical, thermal and porosity properties of mortar samples containing aerogel and silica fume under different curing conditions were investigated. For this purpose, 0%, 0.25% and 0.50% by weight of silica aerogel as a cement additive and 10% silica fume as an industrial waste material were incorporated in the cement mixtures. The prepared mortar samples were exposed to curing process in water, the wetting-drying effect and MgSO4 effect for 16 weeks. The highest thermal conductivity reduction of 31.2% was obtained from the water curing sample with silica fume addition at an aerogel content of 0.25%. Maximum compressive and flexural strengths were determined respectively from samples with silica fume addition at an aerogel content 0.50% as 74.5 MPa and no aerogel content as 11.3 MPa by wetting-drying curing. However, the lowest thermal conductivity coefficient was measured as 1.458 W/mK from the sample at an 0.25% aerogel content containing silica fume which completed the curing process under the influence of MgSO4 with a highest compressive strength increase by 24.6%.
- 30 September 2020
- Published by ALKU Fen Bilimleri Dergisi, Alanya Alaaddin Keykubat University in ALKÜ Fen Bilimleri Dergisi
- Vol. 2 (2) , 54-61
Pirinç Kabuğu Külü Katkılı Harçların Dayanım Ve Dayanıklılık Özelliklerin Araştırılması
Bu çalışmada, tarımsal atık malzemesi olan Pirinç kabuğu külü, çimento yerine ağırlıkça %0, %2, 4%, 6%, 8%, 10%, ve %15 oranlarda kullanılarak toplam 7 farklı bileşime sahip harç numunesi üretilmiştir. Üretilen harç numuneleri üzerinde 28, 56 ve 90 günlük kür süreleri sonunda basınç dayanımı tespitinin yanında 56 günlük kür sonunda donma-çözülme ve ultrasonik hız tayini deneyleri de yapılmıştır. Çalışmada kullanılan bütün karışımlarda Su/Bağlayıcı oranı 0.50 oranında sabit tutulmuştur. Üretilen harç numunelerine ait sonuçlar değerlendirildiğinde %8 Pirinç kabuğu külü ikameli harçların daha yüksek dayanım ve dayanıklılık sonuçları verdiği tespit edilmiştir.
- 30 September 2020
- Published by ALKU Fen Bilimleri Dergisi, Alanya Alaaddin Keykubat University in ALKÜ Fen Bilimleri Dergisi
- Vol. 2 (2) , 54-61
Pirinç Kabuğu Külü Katkılı Harçların Dayanım Ve Dayanıklılık Özelliklerin Araştırılması
Bu çalışmada, tarımsal atık malzemesi olan Pirinç kabuğu külü, çimento yerine ağırlıkça %0, %2, 4%, 6%, 8%, 10%, ve %15 oranlarda kullanılarak toplam 7 farklı bileşime sahip harç numunesi üretilmiştir. Üretilen harç numuneleri üzerinde 28, 56 ve 90 günlük kür süreleri sonunda basınç dayanımı tespitinin yanında 56 günlük kür sonunda donma-çözülme ve ultrasonik hız tayini deneyleri de yapılmıştır. Çalışmada kullanılan bütün karışımlarda Su/Bağlayıcı oranı 0.50 oranında sabit tutulmuştur. Üretilen harç numunelerine ait sonuçlar değerlendirildiğinde %8 Pirinç kabuğu külü ikameli harçların daha yüksek dayanım ve dayanıklılık sonuçları verdiği tespit edilmiştir.
- Open Access
- 1 January 2018
- Published by Wiley in Advances in Civil Engineering
- Vol. 2018 (1)
Mechanical Properties and Thermal Conductivity of Aerogel‐Incorporated Alkali‐Activated Slag Mortars
Compressive strength, thermal conductivity coefficient, and porosimetric properties of alkali‐activated slag (AAS) mortars containing silica aerogel were investigated experimentally in this study. For this purpose, slag mortar mixtures at 0.75% and 1.0% aerogel content ratios were prepared, and these mortar mixtures were activated with lithium carbonate (Li2CO3) at 0.03% and 1.50% dosage rates. Mortar samples were exposed to curing process in water for 2, 7, and 28 days, and the samples, which completed the curing stage, were subjected to the compressive strength test. The porosimetry test and the thermal conductivity coefficient measurement were carried out following the compressive strength test on 28‐day samples. The varying aerogel content rate in the mixtures and the effects of the dosage of Li2CO3 on the gel, capillary, and macropore distributions, and the effect of changing porosimetric properties on compressive strength and thermal conductivity coefficient were analyzed in detail. Experimental studies have shown that AAS mortars including an optimum 0.75% aerogel content rate and 0.03% Li2CO3 activation provided a compressive strength of 34.1 MPa and a thermal conductivity coefficient of 1.32 W/mK. Aerogel addition provides a partial compressive strength increase at 7‐ and 28‐day samples while it also causes maximum strength loss of 5.0% at 2‐day samples.
- 1 January 2018
- Published by Wiley in Advances in Civil Engineering
- Vol. 2018 (1)
Open AccessMechanical Properties and Thermal Conductivity of Aerogel‐Incorporated Alkali‐Activated Slag Mortars
Compressive strength, thermal conductivity coefficient, and porosimetric properties of alkali‐activated slag (AAS) mortars containing silica aerogel were investigated experimentally in this study. For this purpose, slag mortar mixtures at 0.75% and 1.0% aerogel content ratios were prepared, and these mortar mixtures were activated with lithium carbonate (Li2CO3) at 0.03% and 1.50% dosage rates. Mortar samples were exposed to curing process in water for 2, 7, and 28 days, and the samples, which completed the curing stage, were subjected to the compressive strength test. The porosimetry test and the thermal conductivity coefficient measurement were carried out following the compressive strength test on 28‐day samples. The varying aerogel content rate in the mixtures and the effects of the dosage of Li2CO3 on the gel, capillary, and macropore distributions, and the effect of changing porosimetric properties on compressive strength and thermal conductivity coefficient were analyzed in detail. Experimental studies have shown that AAS mortars including an optimum 0.75% aerogel content rate and 0.03% Li2CO3 activation provided a compressive strength of 34.1 MPa and a thermal conductivity coefficient of 1.32 W/mK. Aerogel addition provides a partial compressive strength increase at 7‐ and 28‐day samples while it also causes maximum strength loss of 5.0% at 2‐day samples.
- Open Access
- 31 August 2017
- Published by Pontificia Universidad Catolica de Chile in Revista de la construcción
- Vol. 16 (2) , 355-360
Effect of silica fume and solid borax waste on compressive strength of fired briquettes
- 31 August 2017
- Published by Pontificia Universidad Catolica de Chile in Revista de la construcción
- Vol. 16 (2) , 355-360
Open AccessEffect of silica fume and solid borax waste on compressive strength of fired briquettes
- Open Access
- 5 May 2017
- Published by Pontificia Universidad Catolica de Chile in Revista de la construcción
- Vol. 16 (1) , 167-173
Investigation of mechanical properties of mortars with carbon fiber using multi slice computed tomography
DOI: 10.7764/RDLC.16.1.167 Carbon fibers (CFs) in the cement mortars are used in order to improve characteristics properties of the composite materials such as mechanical properties. Moreover, the uniformity of fiber dispersion is significant aspect for improvement of the composites. Computed Tomography (CT) imaging is a fully nondestructive technique to view features in the interior of opaque solid objects to obtain digital information on their properties. In this study, firstly, flexural test was conducted were investigated for 4×4×16 cm samples incorporated with carbon fiber at 2- and 7-days curing. Secondly, the images that were obtained by using multi-slice CT technique. Finally, the compressive strength properties of the mortars mixed with carbon fiber were discussed. According to the test results, the dispersion and orientation of CFs in the samples have a remarkable impact on mechanical properties of the composites.
- 5 May 2017
- Published by Pontificia Universidad Catolica de Chile in Revista de la construcción
- Vol. 16 (1) , 167-173
Open AccessInvestigation of mechanical properties of mortars with carbon fiber using multi slice computed tomography
DOI: 10.7764/RDLC.16.1.167 Carbon fibers (CFs) in the cement mortars are used in order to improve characteristics properties of the composite materials such as mechanical properties. Moreover, the uniformity of fiber dispersion is significant aspect for improvement of the composites. Computed Tomography (CT) imaging is a fully nondestructive technique to view features in the interior of opaque solid objects to obtain digital information on their properties. In this study, firstly, flexural test was conducted were investigated for 4×4×16 cm samples incorporated with carbon fiber at 2- and 7-days curing. Secondly, the images that were obtained by using multi-slice CT technique. Finally, the compressive strength properties of the mortars mixed with carbon fiber were discussed. According to the test results, the dispersion and orientation of CFs in the samples have a remarkable impact on mechanical properties of the composites.
- 3 March 2017
- Published by Springer Nature in Mechanics of Composite Materials
- Vol. 53 (1) , 123-130
Analysis of Cement-Based Pastes Mixed with Waste Tire Rubber
- 3 March 2017
- Published by Springer Nature in Mechanics of Composite Materials
- Vol. 53 (1) , 123-130
Analysis of Cement-Based Pastes Mixed with Waste Tire Rubber
- 1 October 2016
- Published by Elsevier in Construction and Building Materials
- Vol. 123, 727-733
Characterization of ground slag and borax waste and their effects on the compressive strength of briquettes
- 1 October 2016
- Published by Elsevier in Construction and Building Materials
- Vol. 123, 727-733
Characterization of ground slag and borax waste and their effects on the compressive strength of briquettes
- 1 October 2016
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 28 (10)
Assessment of the Material Quality of Damaged Structures after Earthquake in Van, Turkey
Two earthquakes occurred on October 23 and November 9, 2011, in Van, Turkey, with magnitudes (Mw) of 7.2 and 5.6, respectively. The types of the damage and collapse that occurred in both earthquakes necessitate a detailed examination of the load-bearing elements, which essentially comprise the components of RC buildings, in terms of their material quality. For this purpose, the compressive strengths, X-ray diffraction (XRD), and scanning electron microscopy with X-ray microanalysis (SEM/EDS) were performed on concrete samples collected from the collapsed buildings, with a view to understand the role of the materials in the devastation caused by the earthquakes. Visual observations and the results of the tests showed that there were not only construction and manufacturing failures, but also the strength of the concrete was a crucial factor that contributed to the damage and collapse of the buildings. In addition to these conclusions, results obtained from XRD and SEM-EDS showed that compressive str...
- 1 October 2016
- Published by American Society of Civil Engineers (ASCE) in Journal of Materials in Civil Engineering
- Vol. 28 (10)
Assessment of the Material Quality of Damaged Structures after Earthquake in Van, Turkey
Two earthquakes occurred on October 23 and November 9, 2011, in Van, Turkey, with magnitudes (Mw) of 7.2 and 5.6, respectively. The types of the damage and collapse that occurred in both earthquakes necessitate a detailed examination of the load-bearing elements, which essentially comprise the components of RC buildings, in terms of their material quality. For this purpose, the compressive strengths, X-ray diffraction (XRD), and scanning electron microscopy with X-ray microanalysis (SEM/EDS) were performed on concrete samples collected from the collapsed buildings, with a view to understand the role of the materials in the devastation caused by the earthquakes. Visual observations and the results of the tests showed that there were not only construction and manufacturing failures, but also the strength of the concrete was a crucial factor that contributed to the damage and collapse of the buildings. In addition to these conclusions, results obtained from XRD and SEM-EDS showed that compressive str...
- 1 January 2014
- Published by IACSIT Press in International Journal of Engineering and Technology
- Vol. 6 (1) , 5-8
Utilization of Waste Asphalt as an Additive in Mortars
- 1 January 2014
- Published by IACSIT Press in International Journal of Engineering and Technology
- Vol. 6 (1) , 5-8
Utilization of Waste Asphalt as an Additive in Mortars