Cengiz Duran Atiş
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Cengiz Duran Atiş has a total of 104 co-authors. Here are the top co-authors by number of shared publications:
- Okan Karahan
Erciyes University
14 shared publications Okan Karahan
12 shared publications- Serhan Ilkentapar
Civil Engineering Department, Erciyes University, Kayseri, Turkey
11 shared publications - Uğur Durak
Civil Engineering Department Erciyes University Kayseri Turkey
11 shared publications O. Karahan
6 shared publications- Erion Luga
College of Engineering and Technology, American University of the Middle East, Egaila 54200, Kuwait
5 shared publications
Latest Publications
- Open Access
Residual Mechanical Performance and Mass Loss of Heat-Cured NaOH-Activated Fly Ash/Slag and Portland Cement Mortars After Exposure to Elevated Temperatures
This study compares the residual mechanical performance and mass loss of NaOH-activated Fly Ash (FA), Ground Granulated Blast Furnace Slag (GGBFS) and FA/GGBFS mortars with those of CEM I 42.5R and CEM I 52.5R mortars after exposure to 300, 600 and 900 °C. The alkali-activated mortars were heat-cured at 100 °C for 3 days, whereas the Ordinary Portland Cement (OPC) mortars were water-cured for 28 days, to compare the residual performance of the materials produced under their respective curing regimes. After 900 °C, the GGBFS mortar retained 43.4 MPa in compression (57.5%) and 2.88 MPa in flexure (44.9%), against 6.4–9.1 MPa (11.7–14.6%) and 1.29–1.40 MPa (12.8–16.3%) for the OPC mortars, both differences being statistically significant for each OPC mortar. The FA/GGBFS mortar (33.9 MPa, 50.9% in compression) exceeded the OPC mortars only in mean value; the differences were not statistically significant. GGBFS showed the highest mass loss (7.83% at 900 °C). In a correlation analysis, mass loss mirrored strength loss in the OPC mortars (R2 = 0.92–0.98) but not in the alkali-activated ones (R2 ≤ 0.11), showing that mass loss alone was not a consistent indicator of thermal damage across binder systems. The results indicate that the GGBFS-based NaOH-activated mortar is a promising alternative to OPC for precast building elements that must retain residual load-bearing capacity after high-temperature exposure.
Open AccessResidual Mechanical Performance and Mass Loss of Heat-Cured NaOH-Activated Fly Ash/Slag and Portland Cement Mortars After Exposure to Elevated Temperatures
This study compares the residual mechanical performance and mass loss of NaOH-activated Fly Ash (FA), Ground Granulated Blast Furnace Slag (GGBFS) and FA/GGBFS mortars with those of CEM I 42.5R and CEM I 52.5R mortars after exposure to 300, 600 and 900 °C. The alkali-activated mortars were heat-cured at 100 °C for 3 days, whereas the Ordinary Portland Cement (OPC) mortars were water-cured for 28 days, to compare the residual performance of the materials produced under their respective curing regimes. After 900 °C, the GGBFS mortar retained 43.4 MPa in compression (57.5%) and 2.88 MPa in flexure (44.9%), against 6.4–9.1 MPa (11.7–14.6%) and 1.29–1.40 MPa (12.8–16.3%) for the OPC mortars, both differences being statistically significant for each OPC mortar. The FA/GGBFS mortar (33.9 MPa, 50.9% in compression) exceeded the OPC mortars only in mean value; the differences were not statistically significant. GGBFS showed the highest mass loss (7.83% at 900 °C). In a correlation analysis, mass loss mirrored strength loss in the OPC mortars (R2 = 0.92–0.98) but not in the alkali-activated ones (R2 ≤ 0.11), showing that mass loss alone was not a consistent indicator of thermal damage across binder systems. The results indicate that the GGBFS-based NaOH-activated mortar is a promising alternative to OPC for precast building elements that must retain residual load-bearing capacity after high-temperature exposure.
- Open Access
Hemp Fiber and Expanded Perlite-Incorporated Lightweight Inorganic Polymer Mortars: Mechanical, Thermal Insulation, High-Temperature Resistance, Microstructural Characteristics, and Life Cycle Assessment
In this study, lightweight geopolymer mortars with low environmental impact, high thermal insulation performance, and strong resistance to elevated temperatures were developed. Fly ash, expanded perlite, and bio-based hemp fibers were employed as the binder, aggregate, and reinforcement, respectively. Hemp fibers were prepared in lengths of 1, 2, and 3 cm and incorporated into the mixtures at dosages of 0.50%, 0.75%, and 1.00% by weight of binder. Sodium hydroxide was used as the activator, and specimens were heat-cured at 90 °C for 24–48–72 h. The workability, unit weight, UPV, flexural, and compressive strength of the geopolymer mortars were determined. In addition, thermal conductivity, high-temperature resistance, microstructural characteristics, and environmental impacts of selected mixtures were evaluated. The results demonstrated that lightweight geopolymer mortars could be successfully produced using expanded perlite aggregate and that hemp fibers significantly enhanced mechanical performance up to 48% at one day. Moreover, fiber reinforcement improved thermal insulation capability by up to 5.5% and high-temperature resistance. FESEM, EDX, elemental mapping, and XRD analyses supported the mechanical and physical findings through detailed microstructural evidence. Furthermore, LCA results revealed that fiber incorporation improved the environmental performance of geopolymer mortars, resulting in approximately a 21% reduction in global warming potential compared with the reference mixture.
Open AccessHemp Fiber and Expanded Perlite-Incorporated Lightweight Inorganic Polymer Mortars: Mechanical, Thermal Insulation, High-Temperature Resistance, Microstructural Characteristics, and Life Cycle Assessment
In this study, lightweight geopolymer mortars with low environmental impact, high thermal insulation performance, and strong resistance to elevated temperatures were developed. Fly ash, expanded perlite, and bio-based hemp fibers were employed as the binder, aggregate, and reinforcement, respectively. Hemp fibers were prepared in lengths of 1, 2, and 3 cm and incorporated into the mixtures at dosages of 0.50%, 0.75%, and 1.00% by weight of binder. Sodium hydroxide was used as the activator, and specimens were heat-cured at 90 °C for 24–48–72 h. The workability, unit weight, UPV, flexural, and compressive strength of the geopolymer mortars were determined. In addition, thermal conductivity, high-temperature resistance, microstructural characteristics, and environmental impacts of selected mixtures were evaluated. The results demonstrated that lightweight geopolymer mortars could be successfully produced using expanded perlite aggregate and that hemp fibers significantly enhanced mechanical performance up to 48% at one day. Moreover, fiber reinforcement improved thermal insulation capability by up to 5.5% and high-temperature resistance. FESEM, EDX, elemental mapping, and XRD analyses supported the mechanical and physical findings through detailed microstructural evidence. Furthermore, LCA results revealed that fiber incorporation improved the environmental performance of geopolymer mortars, resulting in approximately a 21% reduction in global warming potential compared with the reference mixture.
- Open Access
Alkali-Activated Binders as Sustainable Alternatives to Portland Cement and Their Resistance to Saline Water
Alkali-activated binders have emerged as promising alternatives to Ordinary Portland Cement (OPC) due to their sustainability features and potential advantages. This study evaluates the durability properties of heat-cured fly ash (FA) and ground granulated blast-furnace slag (GGBFS) geopolymer mortars activated with sodium hydroxide, which were subjected to wet–dry cycling in saline environments. Three series of FA, a FA/GGBFS blend, and GGBFS mortars previously optimized on a compressive strength basis were investigated and compared against two control OPC mixes. Performance indicators such as the water absorption, porosity, flexural strength, and compressive strength were analyzed. The results demonstrate that geopolymer mortars have significantly reduced water absorption and porosity with increasing wet–dry cycles. The compressive strength of the FA/GGBFS mortars also increased from 66.5 MPa (untreated) to 87.9 MPa over 45 cycles. The flexural strength remained stable or improved slightly across all geopolymer mortars. The control OPC specimens experienced significant deterioration, with compressive strength in CEM I 42.5R dropping from 51.8 to 17.1 MPa. These findings highlight the superior durability of geopolymer mortars under harsh saline conditions, demonstrating their potential as a resilient alternative for coastal and marine structures.
Open AccessAlkali-Activated Binders as Sustainable Alternatives to Portland Cement and Their Resistance to Saline Water
Alkali-activated binders have emerged as promising alternatives to Ordinary Portland Cement (OPC) due to their sustainability features and potential advantages. This study evaluates the durability properties of heat-cured fly ash (FA) and ground granulated blast-furnace slag (GGBFS) geopolymer mortars activated with sodium hydroxide, which were subjected to wet–dry cycling in saline environments. Three series of FA, a FA/GGBFS blend, and GGBFS mortars previously optimized on a compressive strength basis were investigated and compared against two control OPC mixes. Performance indicators such as the water absorption, porosity, flexural strength, and compressive strength were analyzed. The results demonstrate that geopolymer mortars have significantly reduced water absorption and porosity with increasing wet–dry cycles. The compressive strength of the FA/GGBFS mortars also increased from 66.5 MPa (untreated) to 87.9 MPa over 45 cycles. The flexural strength remained stable or improved slightly across all geopolymer mortars. The control OPC specimens experienced significant deterioration, with compressive strength in CEM I 42.5R dropping from 51.8 to 17.1 MPa. These findings highlight the superior durability of geopolymer mortars under harsh saline conditions, demonstrating their potential as a resilient alternative for coastal and marine structures.
- Open Access
- 29 February 2024
- Published by Turkish Journal of Engineering in Turkish Journal of Engineering
- Vol. 8 (3) , 436-446
A novel strategy to avoid local optimum: Army-inspired genetic algorithm (AIGA)
Objective functions of which an analytical solution is very difficult or time-consuming are solved using stochastic optimization algorithms. Those optimization algorithms compute an approximate solution for objective functions. For a specific search space, the objective function might have one or more local optima along with the global optimum. When a comparison is made among the algorithms, one optimization algorithm could be more effective than others in finding a solution for certain objective functions. The most important factors affecting the success of optimization algorithms are the greatness of search space and the complexity of the objective function. Reaching the global optimum in huge search spaces is very difficult. In complex objective functions that have many local optima or where the differences between global optimum and local optima are very small, the probability of trapping into the local optimum is high. Existing optimization algorithms could be improved using the search space scanned more successfully to give a better performance. To achieve this aim, we present a novel algorithm, called Army-Inspired Genetic Algorithm (AIGA), which is inspired from military movement. The presented algorithm, apart from other optimization algorithms, searches global optima effectively by dividing the entire search area into territories instead of searching in one piece. Thus, the probability of getting trapped in a local optimum reduces and the probability of finding the global optimum increases. The presented algorithm was tested on well-known benchmark problems. The results shows that AIGA is more efficient algorithm in finding the global optimum than traditional algorithms.
- 29 February 2024
- Published by Turkish Journal of Engineering in Turkish Journal of Engineering
- Vol. 8 (3) , 436-446
Open AccessA novel strategy to avoid local optimum: Army-inspired genetic algorithm (AIGA)
Objective functions of which an analytical solution is very difficult or time-consuming are solved using stochastic optimization algorithms. Those optimization algorithms compute an approximate solution for objective functions. For a specific search space, the objective function might have one or more local optima along with the global optimum. When a comparison is made among the algorithms, one optimization algorithm could be more effective than others in finding a solution for certain objective functions. The most important factors affecting the success of optimization algorithms are the greatness of search space and the complexity of the objective function. Reaching the global optimum in huge search spaces is very difficult. In complex objective functions that have many local optima or where the differences between global optimum and local optima are very small, the probability of trapping into the local optimum is high. Existing optimization algorithms could be improved using the search space scanned more successfully to give a better performance. To achieve this aim, we present a novel algorithm, called Army-Inspired Genetic Algorithm (AIGA), which is inspired from military movement. The presented algorithm, apart from other optimization algorithms, searches global optima effectively by dividing the entire search area into territories instead of searching in one piece. Thus, the probability of getting trapped in a local optimum reduces and the probability of finding the global optimum increases. The presented algorithm was tested on well-known benchmark problems. The results shows that AIGA is more efficient algorithm in finding the global optimum than traditional algorithms.
- 20 November 2023
- Published by Elsevier in Construction and Building Materials
- Vol. 409
Reaction kinetics and properties of pumice-based geopolymer systems cured at room temperature
- 20 November 2023
- Published by Elsevier in Construction and Building Materials
- Vol. 409
Reaction kinetics and properties of pumice-based geopolymer systems cured at room temperature
- Open Access
- 31 January 2023
- Published by Duzce Universitesi Bilim ve Teknoloji Dergisi in Düzce Üniversitesi Bilim ve Teknoloji Dergisi
- Vol. 11 (1) , 288-301
Geri Dönüştürülmüş Atık EPS'nin Yüksek Dayanımlı Hafif Şap Üretiminde Kullanımının Araştırılması
Bu çalışmada, atık genleştirilmiş polistiren (EPS) agregası dere kumu ile yer değiştirerek yüksek dayanımlı hafif şap harçları üretilmiştir. Kaplama ve tesviye amacı ile kullanılan şap harçlarında, atık EPS kullanarak harçların birim hacim ağırlığının azaltılması, ısıl performanslarının arttırılması hedeflenmiştir. Bu amaçla, bir grup geleneksel şap harcı ve beş grup atık EPS içeren, 400 kg/m³ -500 kg/m³ arasında değişen çimento dozajlarına sahip hafif şap harcı hazırlanmıştır. Atık EPS agregaları, dere agregası ile hacimce %0, %20, %40, %60, %80 ve %100 oranında yer değiştirilmiştir. Geleneksel ve hafif şap harçlarının yayılma çapı, birim ağırlık, su emme oranı, görünür boşluk oranı, kılcal su emme, basınç ve eğilme dayanımı, aşınmaya karşı direnç ve ısıl iletkenlik performansı ölçülmüştür. Atık EPS içeren harçların birim hacim ağırlıkları 750 kg/m³ –1950 kg/m³ arasında belirlenerek hafif ağırlıklı şap harcı elde edilmiştir. Ayrıca geleneksel şap harcının ısıl iletkenlik katsayısı 0,6617 W.m/K’dan tamamen atık EPS ikamesi ile 0,2553 W.m/K’ya düşerek %61 daha düşük ısıl iletkenlik elde edilmiştir. Deneysel sonuçlar atık EPS agregasının yer değişim oranına bağlı olarak 6,1 MPa-43,4 MPa aralığında hem orta dayanımlı hem de taşıyıcı hafif beton sınıfında hafif şap harçlarının elde edilebildiğini ortaya koymuştur. Harçlardaki birim ağırlığın düşmesi, yapı ağırlığının azalmasına ve ısıl yalıtım özelliğinin iyileşmesine katkı sunmaktadır. Böylece deprem yükü, yalıtım özellikleri ve atık EPS’nin geri dönüşümü açısından sürdürülebilir hafif şap harcı elde edilmiştir.
- 31 January 2023
- Published by Duzce Universitesi Bilim ve Teknoloji Dergisi in Düzce Üniversitesi Bilim ve Teknoloji Dergisi
- Vol. 11 (1) , 288-301
Open AccessGeri Dönüştürülmüş Atık EPS'nin Yüksek Dayanımlı Hafif Şap Üretiminde Kullanımının Araştırılması
Bu çalışmada, atık genleştirilmiş polistiren (EPS) agregası dere kumu ile yer değiştirerek yüksek dayanımlı hafif şap harçları üretilmiştir. Kaplama ve tesviye amacı ile kullanılan şap harçlarında, atık EPS kullanarak harçların birim hacim ağırlığının azaltılması, ısıl performanslarının arttırılması hedeflenmiştir. Bu amaçla, bir grup geleneksel şap harcı ve beş grup atık EPS içeren, 400 kg/m³ -500 kg/m³ arasında değişen çimento dozajlarına sahip hafif şap harcı hazırlanmıştır. Atık EPS agregaları, dere agregası ile hacimce %0, %20, %40, %60, %80 ve %100 oranında yer değiştirilmiştir. Geleneksel ve hafif şap harçlarının yayılma çapı, birim ağırlık, su emme oranı, görünür boşluk oranı, kılcal su emme, basınç ve eğilme dayanımı, aşınmaya karşı direnç ve ısıl iletkenlik performansı ölçülmüştür. Atık EPS içeren harçların birim hacim ağırlıkları 750 kg/m³ –1950 kg/m³ arasında belirlenerek hafif ağırlıklı şap harcı elde edilmiştir. Ayrıca geleneksel şap harcının ısıl iletkenlik katsayısı 0,6617 W.m/K’dan tamamen atık EPS ikamesi ile 0,2553 W.m/K’ya düşerek %61 daha düşük ısıl iletkenlik elde edilmiştir. Deneysel sonuçlar atık EPS agregasının yer değişim oranına bağlı olarak 6,1 MPa-43,4 MPa aralığında hem orta dayanımlı hem de taşıyıcı hafif beton sınıfında hafif şap harçlarının elde edilebildiğini ortaya koymuştur. Harçlardaki birim ağırlığın düşmesi, yapı ağırlığının azalmasına ve ısıl yalıtım özelliğinin iyileşmesine katkı sunmaktadır. Böylece deprem yükü, yalıtım özellikleri ve atık EPS’nin geri dönüşümü açısından sürdürülebilir hafif şap harcı elde edilmiştir.
- Open Access
- 1 January 2023
- Published by Pontificia Universidad Catolica de Chile in Revista de la construcción
- Vol. 22 (3) , 581-596
Recycling waste expanded polystyrene as aggregate in produc-tion of lightweight screed mortar
The potential use of waste-expanded polystyrene (EPS) beads in the production of lightweight screed mortar (LSM) was investigated. LSM specimens were produced by replacing waste EPS with normal weight aggregate at 20%, 40%, 60%, 80%, and 100% proportions by volume. Workability, unit weight, capillarity, flexural and compressive strength, abrasion resistance, drying shrinkage, and thermal conductivity of the LSMs were determined. Waste EPS replacement by the normal weight aggregate reduced the abrasion resistance and strength properties of LSMs. Waste EPS also caused the LSMs to have lower unit weight and thermal conductivity, significantly. It was concluded that substitution of waste EPS by normal weight aggregate up to 60% can be proposed for adequate strength and heat-insulating properties of LSMs. LSM produced with 60% waste EPS (M60) has 16.3 MPa 28th-day compressive strength with 0.4562 W/m.K thermal conductivity and 1.35 g/cm3 unit weight. Moreover, the recovery of waste EPS contributes to both reducing environmental pollution and storage problems.
- 1 January 2023
- Published by Pontificia Universidad Catolica de Chile in Revista de la construcción
- Vol. 22 (3) , 581-596
Open AccessRecycling waste expanded polystyrene as aggregate in produc-tion of lightweight screed mortar
The potential use of waste-expanded polystyrene (EPS) beads in the production of lightweight screed mortar (LSM) was investigated. LSM specimens were produced by replacing waste EPS with normal weight aggregate at 20%, 40%, 60%, 80%, and 100% proportions by volume. Workability, unit weight, capillarity, flexural and compressive strength, abrasion resistance, drying shrinkage, and thermal conductivity of the LSMs were determined. Waste EPS replacement by the normal weight aggregate reduced the abrasion resistance and strength properties of LSMs. Waste EPS also caused the LSMs to have lower unit weight and thermal conductivity, significantly. It was concluded that substitution of waste EPS by normal weight aggregate up to 60% can be proposed for adequate strength and heat-insulating properties of LSMs. LSM produced with 60% waste EPS (M60) has 16.3 MPa 28th-day compressive strength with 0.4562 W/m.K thermal conductivity and 1.35 g/cm3 unit weight. Moreover, the recovery of waste EPS contributes to both reducing environmental pollution and storage problems.
- Open Access
- 1 January 2023
- Published by Pontificia Universidad Catolica de Chile in Revista de la construcción
- Vol. 22 (2) , 419-430
Synergistic effect of waste glass powder and fly ash on some properties of mortar and notably suppressing alkali-silica reaction
In this study the mitigation influence of incorporating waste glass powder (G) and class F fly ash (F) in mortar as partial cement replacement on the alkali-silica reaction (ASR) between reactive aggregate and alkali contents of cement were investigated. Waste G and F replaced cement separately and together on mass basis at 10%, 20%, and 30%. The unit weight (28 days), water absorption, porosity, compressive, and flexural strength tests were conducted at 28- and 90-day water curing time on 40×40×160 mm prismatic hardened samples and flow table test on fresh mortar. There was a slight reduction of the unit weight, an increased workability, and decreased water absorption and porosity; a little reduction of the compressive strength and flexural strength were seen after the tests. In addition, the expansions of mortar were measured up to 90 days. When 14 days expansions were considered according to ASTM C1260, addition of waste G and F separately reduced the expansion that occurred due to ASR. However, the mixture containing 15% waste G and 15% F together (GF-30) exhibited the lowest expansion in the order of 0.02% which was far lower than 0.10%. The higher replacement ratio of waste G and F together and separately caused lower expansion in mortar.
- 1 January 2023
- Published by Pontificia Universidad Catolica de Chile in Revista de la construcción
- Vol. 22 (2) , 419-430
Open AccessSynergistic effect of waste glass powder and fly ash on some properties of mortar and notably suppressing alkali-silica reaction
In this study the mitigation influence of incorporating waste glass powder (G) and class F fly ash (F) in mortar as partial cement replacement on the alkali-silica reaction (ASR) between reactive aggregate and alkali contents of cement were investigated. Waste G and F replaced cement separately and together on mass basis at 10%, 20%, and 30%. The unit weight (28 days), water absorption, porosity, compressive, and flexural strength tests were conducted at 28- and 90-day water curing time on 40×40×160 mm prismatic hardened samples and flow table test on fresh mortar. There was a slight reduction of the unit weight, an increased workability, and decreased water absorption and porosity; a little reduction of the compressive strength and flexural strength were seen after the tests. In addition, the expansions of mortar were measured up to 90 days. When 14 days expansions were considered according to ASTM C1260, addition of waste G and F separately reduced the expansion that occurred due to ASR. However, the mixture containing 15% waste G and 15% F together (GF-30) exhibited the lowest expansion in the order of 0.02% which was far lower than 0.10%. The higher replacement ratio of waste G and F together and separately caused lower expansion in mortar.
- 31 December 2022
- Published by Echo Academic Publishing in Environmental Research and Technology
- Vol. 5 (4) , 289-295
Comparison of Mechanical and Physical Properties of Screed with and without Expanded Polystyrene (EPS) Particles
In this study, in order to observe the mechanical and physical properties of ordinary screed, sandy-lightweight screed and lightweight screed samples, expanded polystyrene (EPS) was used as fine aggregate and lightweight screed systems were produced by replacing sand at 100%, 50% and 0%. Samples of cement dosages of 250, 300, 350 kg/m3 were produced for lightweight screeds, sandy-lightweight screeds and ordinary screeds. Unit weight, water absorption capacity, flexural strength, compressive strength, fire resistance, abrasion and thermal conductivity tests were performed on the produced screed systems. As a result of the research, it was determined that as EPS ratio increases in screed system; unit weights decreased, water absorption rates increased. Besides, the flexural and compressive strengths, fire and abrasion resistance are also decreased. However, it was observed that the thermal conductivity coefficient reduced with the increment of EPS particles in the screed. In normal, sandy-lightweight and lightweight screeds, it was determined that as the cement dosage increased; the unit weights, flexural and compressive strengths, fire and abrasion resistance increased, water absorption capacity and the thermal conductivity coefficient decreased.
- 31 December 2022
- Published by Echo Academic Publishing in Environmental Research and Technology
- Vol. 5 (4) , 289-295
Comparison of Mechanical and Physical Properties of Screed with and without Expanded Polystyrene (EPS) Particles
In this study, in order to observe the mechanical and physical properties of ordinary screed, sandy-lightweight screed and lightweight screed samples, expanded polystyrene (EPS) was used as fine aggregate and lightweight screed systems were produced by replacing sand at 100%, 50% and 0%. Samples of cement dosages of 250, 300, 350 kg/m3 were produced for lightweight screeds, sandy-lightweight screeds and ordinary screeds. Unit weight, water absorption capacity, flexural strength, compressive strength, fire resistance, abrasion and thermal conductivity tests were performed on the produced screed systems. As a result of the research, it was determined that as EPS ratio increases in screed system; unit weights decreased, water absorption rates increased. Besides, the flexural and compressive strengths, fire and abrasion resistance are also decreased. However, it was observed that the thermal conductivity coefficient reduced with the increment of EPS particles in the screed. In normal, sandy-lightweight and lightweight screeds, it was determined that as the cement dosage increased; the unit weights, flexural and compressive strengths, fire and abrasion resistance increased, water absorption capacity and the thermal conductivity coefficient decreased.