ECErdem Coleri

Erdem Coleri

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Erdem Coleri has a total of 26 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Aggregate Retention Performance and Bleeding Susceptibility of Reclaimed Asphalt Pavement Modified Chip Seals: A Laboratory Investigation

    by Servan Baran, Mayank Sukhija, Erdem Coleri

    Chip seal construction has received increased attention recently because of rising construction costs and reduced funding for new asphalt pavement projects. The cost and carbon footprint of chip seal applications can be reduced using reclaimed asphalt pavement (RAP). In this paper, the suitability of RAP material for chip seal applications was evaluated through laboratory experiments. Aggregate retention performance and bleeding susceptibility of chip seal samples were investigated using two different aggregate sources and emulsion types. The gradation of the collected aggregates was matched with RAP aggregates using sieving and batching. Modified sweep, Vialit, and pull-off tests were conducted to determine the aggregate retention performance of RAP-modified chip seal samples. To evaluate the effect of RAP on bleeding susceptibility, a Hamburg wheel tracker (HWT) device with a rubber wheel was used. Macrotexture values were measured at specific HWT passes using a laser texture scanner, and the number of passes until chip seal failure was iterated. According to the results, the aggregate retention performance of RAP was found to be comparable with that of natural aggregates when a binder with an appropriate charge was used. RAP material showed higher aggregate retention with the cationic binder compared to the anionic binder. The bleeding test results indicated that RAP is more susceptible to bleeding. Overall, laboratory test results showed that RAP can be a good alternative to virgin aggregate and may reduce the need for virgin binders used in chip seal construction.


  • Developing methods and strategies to reduce the impact of rumble strips (RS) on pavement performance

    by Joshua Weaver, Vipul Chitnis, Erdem Coleri

    Despite numerous research studies inspecting the safety benefits of centreline and shoulder rumble strips (RS) on pavements, there has been limited exploration into the impact on pavement durability due to the installation of RS. The RS milling process creates micro-cracks in the pavement structure that could propagate to macro cracks over time with freeze and thaw, moisture damage, and traffic loading, thereby decreasing the lifespan of the pavements. The primary objective of this study was to develop testing procedures for RS samples as well as analysis methods to determine the impact of potential controlling factors such as permeability and resulting moisture damage; freeze–thaw; the presence of microcracks; surface layer sealants (chip seal); RS size, depth, type, and RS location in relation to the longitudinal construction joint. The flexural beam fatigue test suggests that sinusoidal rumble strips had 38% increased fatigue cracking resistance. Moreover, the sinusoidal rumble strip resulted in 41% improved cracking and structural performance in the Hamburg Wheel Tracking Test (HWTT) tests. Also, the rutting performance of sinusoidal rumble strips was similar to the control section without rumble strips. In addition, 0% moisture infiltration was observed in sinusoidal rumble strip specimens.


  • Impact of Emulsion Type, Application Rate, and Adverse Construction Conditions on Tack Coat Performance

    by Blaine M. Wruck, Erdem Coleri, Shashwath Sreedhar, Vikas Kumar

    The tack coat is a bonding agent applied between new and existing asphalt pavement layers. Roadway construction operations inherently introduce adverse conditions, such as dust on the pavement surface and nonuniform coverage (streaking), which can compromise tack coat bond quality. Climatic conditions such as heavy rainfall also create issues late in the construction season. Newly developed engineered tack coat emulsions, which utilize stiff asphalt binders and polymer modifiers, are purported to improve interlayer bonding characteristics and reduce the propensity of early fatigue cracking and pavement failure. This study evaluates engineered tack coats against conventionally used tack coats in a laboratory setting to identify their benefits when subjected to different pavement surface types, application rates, and commonly experienced adverse roadway construction conditions. Monotonic direct shear testing was employed to characterize interlayer bonding using two response parameters, interlayer shear strength and interlayer bond energy. This study advances the knowledge of engineered tack coat performance under real-world conditions and also employs a laboratory sample preparation methodology that is representative of pavement construction in the field.


  • Quantifying In Situ Tack Coat Performance Using the TackBond Tester for Quality Control

    by Blaine M. Wruck, Erdem Coleri, Richard Villarreal, Vikas Kumar, James Batti

    In light of the various quality assurance (QA) issues pertaining to tack coats that occur during construction, there is a need for a means of verifying interlayer bond quality in situ. Despite the immense use of tack coat as a constituent in paving, there are no construction specifications with provisions for the quantification of tack coat bond quality in laboratory or field settings. In this study, a construction QA process for tack coat bond performance was proposed. A novel field tack coat bond strength test device, TackBond, was developed and used for this purpose. The performance of engineered (new tack coat technologies that are tracking less) and conventional tack coats was also evaluated in the laboratory and the field using the developed TackBond test system. The TackBond device was improved in this study by adding features that render it more practical, portable, accurate, and better suited for a variety of pavement surface conditions. Engineered tack coat performance was compared with that of tack coats used conventionally on both milled and overlay surface types. The suitability of the TackBond Test device for capturing the true response of each tack coat was first evaluated by comparing results from TackBond laboratory tests with monotonic direct shear tests (DST) on laboratory-produced samples. Strong correlations between the two test types were achieved. Results of field and laboratory TackBond tests showed that the in situ QA control process developed in this study could be effectively used to improve the in situ tack coat bond performance.

  • Development of a Balanced Mix Design Method in Oregon to Improve Long-Term Pavement Performance

    by Shashwath Sreedhar, Erdem Coleri, Ihsan Ali Obaid, Vikas Kumar

    Most state Departments of Transportation (DOTs) and asphalt contractors do not think that commonly used asphalt mixture properties, such as voids in mineral aggregate (VMA), voids filled with asphalt (VFA), and dust-to-binder ratio, reflect the long-term performance of asphalt mixtures. In addition, there are several new additives, polymers, rubbers, and high-quality binder types incorporated into asphalt mixtures today. Volumetric mixture design methods are not capable of capturing the benefits of using all these new technologies on asphalt mixture performance. Furthermore, the interaction of virgin binders with reclaimed asphalt pavement (RAP) mixtures with high binder replacement contents and the level of RAP binder blending into the asphalt mixture are still not well understood. Because of all these complications related to the more complex structure of asphalt mixtures, simple volumetric evaluations to determine the optimum binder content may not result in reliable asphalt mixture designs. Two volumetrically identical mixtures may provide completely different rutting and cracking performance according to laboratory tests. For all these reasons, in this study performance tests for rutting and cracking are incorporated into current asphalt mixture design methods to make it possible to validate or revise the optimum binder content determined by the volumetric mix design method (the only method currently used for asphalt mix design).


  • Performance of Waterproofing Membranes to Protect Concrete Bridge Decks

    by Matthew A. Haynes, Erdem Coleri, Ihsan Obaid

    The installation of waterproofing membranes on concrete bridge decks is a commonly used strategy to prevent water on the roadway surface from penetrating into the deck and to reduce the load and freeze–thaw related damage to the bridge deck. Typically, an asphalt layer is paved over the waterproofing membrane to prevent damage from heavy vehicles. The early failure of asphalt pavement overlays on concrete bridge decks with waterproofing membranes has been recognized as a significant issue by several transportation agencies. Potential reasons for the failure of the asphalt overlay were thought to be poor adhesion between the waterproofing membrane and the asphalt wearing course, and the material properties of the asphalt layer. By determining the most effective waterproofing methods and strategies, this research will serve to decrease repair and replacement costs, and increase the service life of asphalt overlays on concrete bridge decks. The main goals of this study are to provide the industry and transportation agencies with better insight into the failure mechanisms of asphalt overlays on concrete bridge decks and to establish field and laboratory experiments to evaluate the performance of these overlays. From the results of this study, a poured waterproofing membrane was recommended as an ideal membrane for use on concrete bridge decks because of its ease of installation, complete impermeability, and high bond strengths between the concrete deck, membrane layers, and asphalt overlay.


  • Open Access

    Investigation of Tack Coat Bond Damage Mechanism in Asphalt Surfaced Pavements under Dynamic Truck Loads

    by Mostafa Estaji, Erdem Coleri, Blaine Wruck

    Bonding created by the tack coat allows the pavement system to carry heavy truck loads as a monolithic structure and improves the structural integrity. In Oregon and throughout the U.S.A., CSS-1H is the most commonly used tack coat type. However, field observations have revealed that new engineered tack coats, although more expensive, outperform the conventional types in relation to shear resistance. In this study, the impact of these new engineered emulsions on in-situ bond performance was quantified by laboratory testing and numerical modeling. Bonding damage performance of all tack coats was experimentally determined by using direct shear tests. Full-scale moving truck load models were developed and calibrated using the load-displacement parameters obtained from the laboratory shear tests. The impact of adverse construction conditions, such as dust, rain, and tack coat coverage, on tack coat bond damage under heavy truck loads was determined. It was concluded that the presence of dust had relatively the lowest contribution to shear damage. Rain during construction had the highest impact on the damage behavior and tack coat application on a wet surface increases the potential for damage by 20.1%. A 50% coverage of tack coat during construction resulted in 12.8% higher damage levels compared with 100% tack coat coverage of the surface area. Moving load models for heavy trucks caused 2.44 times more bonding damage at the bonded interface compared with the damage created by smaller trucks (F450).